SIST EN ISO 10366-1:2003
(Main)Plastics - Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 10366-1:2002)
Plastics - Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 10366-1:2002)
1.1 ISO 10366-1:2002 establishes a system of designation for methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials, which may be used as the basis for specifications.
1.2 The types of MABS plastic are differentiated from each other by a classification system based on appropriate levels of the designatory properties
Vicat softening temperature
melt volume-flow rate
Charpy notched impact strength
tensile modulus
and on information about composition, intended application and/or method of processing, important properties, additives, colorants, fillers and reinforcing materials.
1.3 This part of ISO 10366 is applicable to all methyl methacrylate-acrylonitrile-butadiene-styrene materials consisting of a continuous phase based mainly on copolymers of styrene (and/or alkyl-substituted styrene), acrylonitrile and methyl methacrylate and a dispersed elastomeric phase based mainly on polybutadiene.
It applies to MABS materials ready for normal use in the form of powder, granules or pellets, unmodified or modified by colorants, additives, fillers, etc.
Kunststoffe - Methylmethacrylat-Acrylnitril-Butadien-Styrol (MABS)-Formmassen - Teil 1: Bezeichnungssystem und Basis für Spezifikationen (ISO 10366-1:2002)
1.1 In diesem Teil von ISO 10366 wird ein Bezeichnungssystem für thermoplastische Methylmethacrylat-Acrylnitril-Butadien-Styrol (MABS)-Formmassen festgelegt, das als Grundlage für Spezifikationen dienen kann.
1.2 MABS-Formmasse-Typen werden mit Hilfe eines Einteilungssytems voneinander unterschieden, das auf geeigneten Wertebereichen der kennzeichnenden Eigenschaften:
a) Vicat-Erweichungstemperatur,
b) Schmelze-Volumenfließrate,
c) Charpy-Kerbschlagzähigkeit,
d) Zug-Modul
und auf Informationen über Zusammensetzung, vorgesehene Anwendung und/oder Verarbeitungsverfahren, wichtige Eigenschaften, Additive, Farbstoffe, Füll- und Verstärkungsstoffe beruht.
1.3 Dieser Teil von ISO 10366 ist anwendbar auf alle Methylmethacrylat-Acrylnitril-Butadien-Styrol-Formmassen mit einer kontinuierlichen Phase vorwiegend auf der Basis von Polymeren des Styrols (und/oder alkylsubstituierten Styrols), Acrylnitrils und Methylmethacrylats und einer dispersen elastomeren Phase auf der Basis von Butadien.
Er gilt für gebrauchsfertige MABS-Formmassen in Form von Pulver, Granulaten oder Pellets, nicht modifiziert oder modifiziert mit Farbstoffen, Additiven, Füllstoffen usw.
1.4 Es soll nicht unterstellt werden, dass Formmassen mit gleicher Bezeichnung notwendigerweise auch Gleiches leisten. Dieser Teil von ISO 10366 enthält keine technischen Daten, Leistungsangaben oder Verarbeitungsbedingungen, die notwendig sein können, um eine Formmasse für eine spezielle Anwendung und/oder ein bestimmtes Verarbeitungsverfahren zu spezifizieren.
Wenn solche zusätzlichen Eigenschaften gefragt sind, müssen sie, soweit möglich, mit Hilfe der in Teil 2 dieser Norm festgelegten Prüfverfahren bestimmt werden.
1.5 Um eine thermoplastische Formmasse für eine bestimmte Anwendung zu spezifizieren oder eine reproduzierbare Verarbeitung sicherzustellen, dürfen zusätzliche Anforderungen im Daten-Block 5 festgelegt werden (siehe 3.1).
Plastiques - Méthylméthacrylate-acrylonitrile-butadiene-styrene (MABS) pour moulage et extrusion - Partie 1: Systeme de désignation et base de spécifications (ISO 10366-1:2002)
L'ISO 10366:2002 établit un système de désignation des matériaux thermoplastiques méthacrylate de méthyle-acrylonitrile-butadiène-styrène (MABS) qui peut être utilisé comme base pour les spécifications.
Les types de plastiques MABS sont différenciés les uns des autres par un système de classification basé sur des niveaux appropriés des propriétés de désignation
température de ramollissement Vicat
indice de fluidité à chaud
résistance au choc Charpy
module de traction
et des informations concernant la composition, l'application prévue et/ou la méthode de mise en oeuvre, les propriétés importantes, les additifs, les colorants, les matériaux de charge et de renfort.
L'ISO 10366:2002 est applicable à tous les copolymères transparents de méthacrylate de méthyle-acrylonitrile-butadiène-styrène comprenant une phase continue composée de copolymères du styrène (et/ou d'un styrène avec substitution par des groupements alkyles), de l'acrylonitrile, du polyméthacrylate de méthyle et une phase élastomère dispersée à base de butadiène.
Elle s'applique aux matériaux MABS prêts à l'emploi sous forme de poudres, de grains ou de granulés, et à des matériaux non modifiés ou modifiés par des colorants, des additifs, des charges etc.
Polimerni materiali - Materiali za oblikovanje in ekstrudiranje na osnovi metilmetakrilat-akrilonitril-butadien-stirena (MABS) - 1. del: Sistem označevanja in podlage za specifikacije (ISO 10366-1:2002)
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Kunststoffe - Methylmethacrylat-Acrylnitril-Butadien-Styrol (MABS)-Formmassen - Teil 1: Bezeichnungssystem und Basis für Spezifikationen (ISO 10366-1:2002)Plastiques - Méthylméthacrylate-acrylonitrile-butadiene-styrene (MABS) pour moulage et extrusion - Partie 1: Systeme de désignation et base de spécifications (ISO 10366-1:2002)Plastics - Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 10366-1:2002)83.080.20PlastomeriThermoplastic materialsICS:Ta slovenski standard je istoveten z:EN ISO 10366-1:2002SIST EN ISO 10366-1:2003en01-maj-2003SIST EN ISO 10366-1:2003SLOVENSKI
STANDARDSIST EN ISO 10366-1:20001DGRPHãþD
SIST EN ISO 10366-1:2003
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN ISO 10366-1October 2002ICS 83.080.20Supersedes EN ISO 10366-1:1999English versionPlastics - Methyl methacrylate-acrylonitrile-butadiene-styrene(MABS) moulding and extrusion materials - Part 1: Designationsystem and basis for specifications (ISO 10366-1:2002)Plastiques - Méthylméthacrylate-acrylonitrile-butadiène-styrène (MABS) pour moulage et extrusion - Partie 1:Système de désignation et base de spécifications (ISO10366-1:2002)Kunststoffe - Methylmethacrylat-Acrylnitril-Butadien-Styrol(MABS)-Formmassen - Teil 1: Bezeichnungssystem undBasis für Spezifikationen (ISO 10366-1:2002)This European Standard was approved by CEN on 25 August 2002.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2002 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN ISO 10366-1:2002 ESIST EN ISO 10366-1:2003
EN ISO 10366-1:2002 (E)2CORRECTED
2002-11-13ForewordThis document (EN ISO 10366-1:2002) has been prepared by Technical Committee ISO/TC 61"Plastics" in collaboration with Technical Committee CEN/TC 249 "Plastics", the secretariat ofwhich is held by IBN.This European Standard shall be given the status of a national standard, either by publication ofan identical text or by endorsement, at the latest by April 2003, and conflicting nationalstandards shall be withdrawn at the latest by April 2003.This document supersedes EN ISO 10366-1:1999.According to the CEN/CENELEC Internal Regulations, the national standards organizations ofthe following countries are bound to implement this European Standard: Austria, Belgium, CzechRepublic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg,Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.Endorsement noticeThe text of ISO 10366-1:2002 has been approved by CEN as EN ISO 10366-1:2002 without anymodifications.NOTE
Normative references to International Standards are listed in Annex ZA (normative).SIST EN ISO 10366-1:2003
EN ISO 10366-1:2002 (E)3Annex ZA(normative)Normative references to international publicationswith their relevant European publicationsThis European Standard incorporates by dated or undated reference, provisions from otherpublications. These normative references are cited at the appropriate places in the text and thepublications are listed hereafter. For dated references, subsequent amendments to or revisions ofany of these publications apply to this European Standard only when incorporated in it byamendment or revision. For undated references the latest edition of the publication referred toapplies (including amendments).NOTE Where an International Publication has been modified by common modifications, indicatedby (mod.), the relevant EN/HD applies.PublicationYearTitleEN/HDYearISO 1043-12001Plastics - Symbols and abbreviated terms -Part 1: Basic polymers and their specialcharacteristicsEN ISO 1043-12001ISO 10366-21994Plastics - Methylmethacrylate/acrylonitrile/butadiene/styrene(MABS) moulding and extrusion materials -Part 2: Preparation of test specimens anddetermination of propertiesEN ISO 10366-21999SIST EN ISO 10366-1:2003
SIST EN ISO 10366-1:2003
Reference numberISO 10366-1:2002(E)© ISO 2002
INTERNATIONAL STANDARD ISO10366-1Second edition2002-10-01Plastics — Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials — Part 1: Designation system and basis for specifications Plastiques — Méthylméthacrylate-acrylonitrile-butadiène-styrène (MABS) pour moulage et extrusion — Partie 1: Système de désignation et base de spécifications
SIST EN ISO 10366-1:2003
ISO 10366-1:2002(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
©
ISO 2002 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
copyright@iso.ch Web
www.iso.ch Printed in Switzerland
ii © ISO 2002 – All rights reserved
SIST EN ISO 10366-1:2003
ISO 10366-1:2002(E) © ISO 2002 – All rights reserved iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this part of ISO 10366 may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 10366-1 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 9, Thermoplastic materials. This second edition cancels and replaces the first edition (ISO 10366-1:1993), which has been technically revised. ISO 10366 consists of the following parts, under the general title Plastics — Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials: — Part 1: Designation system and basis for specifications — Part 2: Preparation of test specimens and determination of properties
SIST EN ISO 10366-1:2003
SIST EN ISO 10366-1:2003
INTERNATIONAL STANDARD ISO 10366-1:2002(E) © ISO 2002 – All rights reserved 1 Plastics — Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials —
Part 1: Designation system and basis for specifications 1 Scope 1.1 This part of ISO 10366 establishes a system of designation for methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials, which may be used as the basis for specifications. 1.2 The types of MABS plastic are differentiated from each other by a classification system based on appropriate levels of the designatory properties a) Vicat softening temperature b) melt volume-flow rate c) Charpy notched impact strength d) tensile modulus and on information about composition, intended application and/or method of processing, important properties, additives, colorants, fillers and reinforcing materials. 1.3 I This part of ISO 10366 is applicable to all methyl methacrylate-acrylonitrile-butadiene-styrene materials consisting of a continuous phase based mainly on copolymers of styrene (and/or an alkyl-substituted styrene), acrylonitrile and methyl methacrylate and a dispersed elastomeric phase based on butadiene. It applies to MABS materials ready for normal use in the form of powder, granules or pellets, unmodified or modified by colorants, additives, fillers, etc. 1.4 It is not intended to imply that materials having the same designation give necessarily the same performance. This part of ISO 10366 does not provide engineering d
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.