SIST EN 300 019-2-0 V2.2.1:2022

• Abstract:

  The present document specifies the test severities and methods for verification of the required resistibility for equipment ; which is to be stored, transported and used in the environments which characteristics are defined in ETSI ; EN 300 019-1 [2]. ; The purpose of the present document is to provide a general overview of ETSI EN 300 019-2 [3]. ; ETSI TR 100 035 [i.1] should be used in conjunction with ETSI EN 300 019 multi-parts deliverable [2] and [3]. It gives ; an introduction to the main concepts of environmental engineering, the purpose and use of environmental classes and ; the corresponding test philosophy.

• Status: Published
• Public Enquiry End Date: 30-Dec-2021
• Publication Date: 04-Sep-2022
• ICS: 19.040 - Environmental testing
• ICS: 33.050.01 - Telecommunication terminal equipment in general
• Technical Committee: SPN - Services and Protocols for Networks
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 22-Aug-2022
• Due Date: 27-Oct-2022
• Completion Date: 05-Sep-2022
• Ref Project: ETSI EN 300 019-2-0 V2.2.1 (2022-08) - Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 2: Specification of environmental tests; Sub-part 0: Introduction

Overview

SIST EN 300 019-2-0 V2.2.1:2022 is a Slovenian adoption of the European Standard developed by ETSI for environmental engineering in telecommunications. Titled "Environmental Engineering (EE) - Environmental conditions and environmental tests for telecommunications equipment - Part 2: Specification of environmental tests - Sub-part 0: Introduction," this document provides a broad introduction and general overview of the test requirements and methodologies for telecommunications equipment during its lifecycle-encompassing storage, transportation, and in-use conditions, as defined in ETSI EN 300 019-1.

The document outlines the intent and structure of the full ETSI EN 300 019-2 series and serves as a guide to understanding the relevant principles, environmental classifications, and test philosophies essential for verifying equipment resistibility to environmental influences.

Key Topics

• Environmental Classes: Introduction to environmental classes relevant to telecommunications equipment, based on diverse operational scenarios, such as storage, transportation, and deployment in different environments.
• Test Severities and Methods: Explanation of test severities and the criteria for testing that align with the environmental classes from ETSI EN 300 019-1.
• Test Philosophy: Guidance on the purpose and application of environmental tests, focusing on verification of performance criteria without simulating actual product lifetime or reliability.
• States of Test Item: Description of testing both in the "in-use" state (equipment in operational condition) and "not in-use" state (during storage and transport, possibly in packaging).
• Selection and Creation of Test Programmes: Consideration criteria for selecting relevant tests, customizing severities, and combining different test conditions based on product or environmental risk.
• Performance Criteria and Verification: Outlines requirements for assessing equipment before, during, and after tests to ensure compliance with performance benchmarks specified in related product standards.

Applications

The standard is widely used in the telecommunications industry for:

• Product Development and Qualification: Ensuring telecommunications equipment-such as base stations, network hardware, or terminals-can withstand environmental stresses encountered during storage, transportation, and operation.
• Quality Assurance and Procurement: Providing verifiable benchmarks that manufacturers and buyers can use to specify, test, and validate equipment for specific deployment conditions.
• Regulatory Compliance: Facilitating the demonstration of compliance with national and European regulatory frameworks related to environmental endurance and product safety.
• Risk Management: Enabling design engineers, test engineers, and procurement professionals to minimize failures in field operation by identifying and verifying environmental resistibility as part of the product’s lifecycle.
• Test Planning in Laboratories: Serving as foundational documentation for constructing test programs that are harmonized with the latest European and international testing methodologies.

Related Standards

• ETSI EN 300 019-1 (all sub-parts): Defines the environmental classes and conditions for telecommunications equipment as the prerequisite to test specifications.
• ETSI EN 300 019-2 (all sub-parts): Details the specific test procedures, severities, and methods for verifying resistibility of equipment against environmental classes.
• ETSI TR 100 035: Offers additional guidance and terminology related to environmental engineering.
• IEC 60068-2 series: Basis for most environmental testing methods and procedures cited in telecommunications equipment standards.
• IEC 60721-2-4: Provides further context on natural environmental conditions (e.g., solar radiation and temperature) affecting telecommunications equipment.

SIST EN 300 019-2-0 V2.2.1:2022 is a crucial introduction for engineers and professionals involved in environmental testing, equipment specification, and lifecycle management of telecommunications products, aligning Slovenian practice with pan-European and international standards for environmental performance and reliability.

Draft ETSI EN 300 019-2-0 V2.1.6 (2021-10)

EUROPEAN STANDARD
Environmental Engineering (EE);
Environmental conditions and environmental tests for
telecommunications equipment;
Part 2: Specification of environmental tests;
Sub-part 0: Introduction
2 Draft ETSI EN 300 019-2-0 V2.1.6 (2021-10)
Reference
REN/EE-017010
Keywords
environment, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: [phone]  Fax: [phone]
Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.
Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2021.
All rights reserved.
ETSI
3 Draft ETSI EN 300 019-2-0 V2.1.6 (2021-10)
Contents
Intellectual Property Rights . 4
Foreword . 4
Modal verbs terminology . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 6
3 Definition of terms, symbols and abbreviations . 7
3.1 Terms . 7
3.2 Symbols . 7
3.3 Abbreviations . 7
4 General . 7
5 Users guide . 8
5.1 Test specifications and the states of test item . 8
5.1.0 General . 8
5.1.1 In-use tests . 8
5.1.2 Not in-use tests . 9
5.2 Selection of tests and test severities . 9
6 Topics on making a test programme . 9
6.0 General . 9
6.1 Environmental resistibility requirements . 9
6.2 Test programme . 10
6.3 Verification. 10
Annex A (informative): Change History . 12
History . 13
ETSI
4 Draft ETSI EN 300 019-2-0 V2.1.6 (2021-10)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The declarations
pertaining to these essential IPRs, if any, are publicly available for ETSI members and non-members, and can be
found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to
ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the
ETSI Web server (https://ipr.etsi.org/).
Pursuant to the ETSI Directives including the ETSI IPR Policy, no investigation regarding the essentiality of IPRs,
including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not
referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become,
essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its

Members. 3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and of the 3GPP
Organizational Partners. oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and of the ®
oneM2M Partners. GSM and the GSM logo are trademarks registered and owned by the GSM Association.
Foreword
This draft European Standard (EN) has been produced by ETSI Technical Committee Environmental Engineering (EE),
and is now submitted for the combined Public Enquiry and Vote phase of the ETSI standards EN Approval Procedure.
The present document is part 2, sub-part 0 of a multi-part deliverable covering environmental conditions and
environmental tests for telecommunications equipment, as identified below:
Part 1: "Classification of environmental conditions";
Part 2: "Specification of environmental tests";
Sub-part 0: "Introduction";
Sub-part 1: "Storage";
Sub-part 2: "Transportation";
Sub-part 3: "Stationary use at weatherprotected locations";
Sub-part 4: "Stationary use at non-weatherprotected locations";
Sub-part 5: "Ground vehicle installations";
Sub-part 6: "Ship environments";
Sub-part 7: "Portable and non-stationary use";
Sub-part 8: "Stationary use at underground locations".
Part 1 specifies different standardized environmental classes covering climatic, biological, chemically and mechanically
active substances, and mechanical conditions during storage, transportation and in use.
Part 2 specifies the test severities, test methods and performance criteria for the different environmental classes.
ETSI
5 Draft ETSI EN 300 019-2-0 V2.1.6 (2021-10)

Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 6 months after doa

Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.

ETSI
6 Draft ETSI EN 300 019-2-0 V2.1.6 (2021-10)
1 Scope
The present document specifies the test severities and methods for verification of the required resistibility for equipment
which is to be stored, transported and used in the environments which characteristics are defined in ETSI
EN 300 019-1 [2].
The purpose of the present document is to provide a general overview of ETSI EN 300 019-2 [3].
ETSI TR 100 035 [i.1] should be used in conjunction with ETSI EN 300 019 multi-parts deliverable. It gives an
introduction to the main concepts of environmental engineering, the purpose and use of environmental classes and the
corresponding test philosophy.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
[1] ETSI EN 300 019-1-0: " Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 1-0: Classification of environmental
conditions; Introduction".
[2] ETSI EN 300 019-1 (all sub-parts): "Environmental Engineering (EE); Environmental conditions
and environmental tests for telecommunications equipment; Part 1: Classification of
environmental conditions".
[3] ETSI EN 300 019-2 (all sub-parts): "Environmental Engineering (EE); Environmental conditions
and environmental tests for telecommunications equipment; Part 2: Specification of environmental
tests".
[4] Void.
[5] IEC 60068-2 series: "Environmental testing".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarante
...

Final draft ETSI EN 300 019-2-0 V2.2.0 (2022-06)

EUROPEAN STANDARD
Environmental Engineering (EE);
Environmental conditions and environmental tests for
telecommunications equipment;
Part 2: Specification of environmental tests;
Sub-part 0: Introduction
2 Final draft ETSI EN 300 019-2-0 V2.2.0 (2022-06)

Reference
REN/EE-017010
Keywords
environment, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: [phone]  Fax: [phone]

Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
If you find a security vulnerability in the present document, please report it through our
Coordinated Vulnerability Disclosure Program:
https://www.etsi.org/standards/coordinated-vulnerability-disclosure
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.

Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2022.
All rights reserved.
ETSI
3 Final draft ETSI EN 300 019-2-0 V2.2.0 (2022-06)
Contents
Intellectual Property Rights . 4
Foreword . 4
Modal verbs terminology . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 6
3 Definition of terms, symbols and abbreviations . 7
3.1 Terms . 7
3.2 Symbols . 7
3.3 Abbreviations . 7
4 General . 7
5 Users guide . 8
5.1 Test specifications and the states of test item . 8
5.1.0 General . 8
5.1.1 In-use tests . 8
5.1.2 Not in-use tests . 9
5.2 Selection of tests and test severities . 9
6 Topics on making a test programme . 9
6.0 General . 9
6.1 Environmental resistibility requirements . 9
6.2 Test programme . 10
6.3 Verification. 11
Annex A (informative): Change History . 12
History . 13

ETSI
4 Final draft ETSI EN 300 019-2-0 V2.2.0 (2022-06)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The declarations
pertaining to these essential IPRs, if any, are publicly available for ETSI members and non-members, and can be
found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to
ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the
ETSI Web server (https://ipr.etsi.org/).
Pursuant to the ETSI Directives including the ETSI IPR Policy, no investigation regarding the essentiality of IPRs,
including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not
referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become,
essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its

Members. 3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and of the 3GPP
Organizational Partners. oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and of the ®
oneM2M Partners. GSM and the GSM logo are trademarks registered and owned by the GSM Association.
Foreword
This final draft European Standard (EN) has been produced by ETSI Technical Committee Environmental Engineering
(EE), and is now submitted for the Vote phase of the ETSI standards EN Approval Procedure.
The present document is part 2, sub-part 0 of a multi-part deliverable covering environmental conditions and
environmental tests for telecommunications equipment, as identified below:
Part 1: "Classification of environmental conditions";
Part 2: "Specification of environmental tests";
Sub-part 0: "Introduction";
Sub-part 1: "Storage";
Sub-part 2: "Transportation";
Sub-part 3: "Stationary use at weatherprotected locations";
Sub-part 4: "Stationary use at non-weatherprotected locations";
Sub-part 5: "Ground vehicle installations";
Sub-part 6: "Ship environments";
Sub-part 7: "Portable and non-stationary use";
Sub-part 8: "Stationary use at underground locations".
Part 1 specifies different standardized environmental classes covering climatic, biological, chemically and mechanically
active substances, and mechanical conditions during storage, transportation and in use.
Part 2 specifies the test severities, test methods and performance criteria for the different environmental classes.
ETSI
5 Final draft ETSI EN 300 019-2-0 V2.2.0 (2022-06)

Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 6 months after doa

Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.

ETSI
6 Final draft ETSI EN 300 019-2-0 V2.2.0 (2022-06)
1 Scope
The present document specifies the test severities and methods for verification of the required resistibility for equipment
which is to be stored, transported and used in the environments which characteristics are defined in ETSI
EN 300 019-1 [2].
The purpose of the present document is to provide a general overview of ETSI EN 300 019-2 [3].
ETSI TR 100 035 [i.1] should be used in conjunction with ETSI EN 300 019 multi-parts deliverable [2] and [3]. It gives
an introduction to the main concepts of environmental engineering, the purpose and use of environmental classes and
the corresponding test philosophy.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] ETSI EN 300 019-1-0: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 1-0: Classification of environmental
conditions; Introduction".
[2] ETSI EN 300 019-1 (all sub-parts): "Environmental Engineering (EE); Environmental conditions
and environmental tests for telecommunications equipment; Part 1: Classification of
environmental conditions".
[3] ETSI EN 300 019-2 (all sub-parts): "Environmental Engineering (EE); Environmental conditions
and environmental tests for telecommunications equipment; Part 2: Specification of environmental
tests".
[4] Void.
[5] IEC 60068-2 series: "Environmental testing".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] ETSI TR 100 035: "Environmental Engineering (EE); Environmental engineering; Guidance and
terminology".
ETS
...

EUROPEAN STANDARD
Environmental Engineering (EE);
Environmental conditions and environmental tests for
telecommunications equipment;
Part 2: Specification of environmental tests;
Sub-part 0: Introduction
2 ETSI EN 300 019-2-0 V2.2.1 (2022-08)

Reference
REN/EE-017010
Keywords
environment, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: [phone]  Fax: [phone]

Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
If you find a security vulnerability in the present document, please report it through our
Coordinated Vulnerability Disclosure Program:
https://www.etsi.org/standards/coordinated-vulnerability-disclosure
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.

Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2022.
All rights reserved.
ETSI
3 ETSI EN 300 019-2-0 V2.2.1 (2022-08)
Contents
Intellectual Property Rights . 4
Foreword . 4
Modal verbs terminology . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 6
3 Definition of terms, symbols and abbreviations . 7
3.1 Terms . 7
3.2 Symbols . 7
3.3 Abbreviations . 7
4 General . 7
5 Users guide . 8
5.1 Test specifications and the states of test item . 8
5.1.0 General . 8
5.1.1 In-use tests . 8
5.1.2 Not in-use tests . 9
5.2 Selection of tests and test severities . 9
6 Topics on making a test programme . 9
6.0 General . 9
6.1 Environmental resistibility requirements . 9
6.2 Test programme . 10
6.3 Verification. 11
Annex A (informative): Change History . 12
History . 13

ETSI
4 ETSI EN 300 019-2-0 V2.2.1 (2022-08)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The declarations
pertaining to these essential IPRs, if any, are publicly available for ETSI members and non-members, and can be
found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to
ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the
ETSI Web server (https://ipr.etsi.org/).
Pursuant to the ETSI Directives including the ETSI IPR Policy, no investigation regarding the essentiality of IPRs,
including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not
referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become,
essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its

Members. 3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and of the 3GPP
Organizational Partners. oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and of the ®
oneM2M Partners. GSM and the GSM logo are trademarks registered and owned by the GSM Association.
Foreword
This European Standard (EN) has been produced by ETSI Technical Committee Environmental Engineering (EE).
The present document is part 2, sub-part 0 of a multi-part deliverable covering environmental conditions and
environmental tests for telecommunications equipment, as identified below:
Part 1: "Classification of environmental conditions";
Part 2: "Specification of environmental tests";
Sub-part 0: "Introduction";
Sub-part 1: "Storage";
Sub-part 2: "Transportation";
Sub-part 3: "Stationary use at weatherprotected locations";
Sub-part 4: "Stationary use at non-weatherprotected locations";
Sub-part 5: "Ground vehicle installations";
Sub-part 6: "Ship environments";
Sub-part 7: "Portable and non-stationary use";
Sub-part 8: "Stationary use at underground locations".
Part 1 specifies different standardized environmental classes covering climatic, biological, chemically and mechanically
active substances, and mechanical conditions during storage, transportation and in use.
Part 2 specifies the test severities, test methods and performance criteria for the different environmental classes.

ETSI
5 ETSI EN 300 019-2-0 V2.2.1 (2022-08)
National transposition dates
Date of adoption of this EN: 9 August 2022
Date of latest announcement of this EN (doa): 30 November 2022
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 May 2023
Date of withdrawal of any conflicting National Standard (dow): 31 May 2023

Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.

ETSI
6 ETSI EN 300 019-2-0 V2.2.1 (2022-08)
1 Scope
The present document specifies the test severities and methods for verification of the required resistibility for equipment
which is to be stored, transported and used in the environments which characteristics are defined in ETSI
EN 300 019-1 [2].
The purpose of the present document is to provide a general overview of ETSI EN 300 019-2 [3].
ETSI TR 100 035 [i.1] should be used in conjunction with ETSI EN 300 019 multi-parts deliverable [2] and [3]. It gives
an introduction to the main concepts of environmental engineering, the purpose and use of environmental classes and
the corresponding test philosophy.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] ETSI EN 300 019-1-0: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 1-0: Classification of environmental
conditions; Introduction".
[2] ETSI EN 300 019-1 (all sub-parts): "Environmental Engineering (EE); Environmental conditions
and environmental tests for telecommunications equipment; Part 1: Classification of
environmental conditions".
[3] ETSI EN 300 019-2 (all sub-parts): "Environmental Engineering (EE); Environmental conditions
and environmental tests for telecommunications equipment; Part 2: Specification of environmental
tests".
[4] Void.
[5] IEC 60068-2 series: "Environmental testing".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] ETSI TR 100 035: "Environmental Engineering (EE); Environmental engineering; Guidance and
terminology".
ETSI
...

SLOVENSKI STANDARD
01-oktober-2022
Okoljski inženiring (EE) - Okoljski pogoji in preskusi okoljskih vplivov na
telekomunikacijsko opremo - 2. del: Specifikacija preskusov okoljskih vplivov - 0.
poddel: Uvod
Environmental Engineering (EE) - Environmental conditions and environmental tests for
telecommunications equipment - Part 2: Specification of environmental tests - Sub-part
0: Introduction
Ta slovenski standard je istoveten z: ETSI EN 300 019-2-0 V2.2.1 (2022-08)
ICS:
19.040 Preskušanje v zvezi z Environmental testing
okoljem
33.050.01 Telekomunikacijska Telecommunication terminal
terminalska oprema na equipment in general
splošno
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
Environmental Engineering (EE);
Environmental conditions and environmental tests for
telecommunications equipment;
Part 2: Specification of environmental tests;
Sub-part 0: Introduction
2 ETSI EN 300 019-2-0 V2.2.1 (2022-08)

Reference
REN/EE-017010
Keywords
environment, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: [phone]  Fax: [phone]

Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
If you find a security vulnerability in the present document, please report it through our
Coordinated Vulnerability Disclosure Program:
https://www.etsi.org/standards/coordinated-vulnerability-disclosure
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.

Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2022.
All rights reserved.
ETSI
3 ETSI EN 300 019-2-0 V2.2.1 (2022-08)
Contents
Intellectual Property Rights . 4
Foreword . 4
Modal verbs terminology . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 6
3 Definition of terms, symbols and abbreviations . 7
3.1 Terms . 7
3.2 Symbols . 7
3.3 Abbreviations . 7
4 General . 7
5 Users guide . 8
5.1 Test specifications and the states of test item . 8
5.1.0 General . 8
5.1.1 In-use tests . 8
5.1.2 Not in-use tests . 9
5.2 Selection of tests and test severities . 9
6 Topics on making a test programme . 9
6.0 General . 9
6.1 Environmental resistibility requirements . 9
6.2 Test programme . 10
6.3 Verification. 11
Annex A (informative): Change History . 12
History . 13

ETSI
4 ETSI EN 300 019-2-0 V2.2.1 (2022-08)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The declarations
pertaining to these essential IPRs, if any, are publicly available for ETSI members and non-members, and can be
found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to
ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the
ETSI Web server (https://ipr.etsi.org/).
Pursuant to the ETSI Directives including the ETSI IPR Policy, no investigation regarding the essentiality of IPRs,
including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not
referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become,
essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its

Members. 3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and of the 3GPP
Organizational Partners. oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and of the ®
oneM2M Partners. GSM and the GSM logo are trademarks registered and owned by the GSM Association.
Foreword
This European Standard (EN) has been produced by ETSI Technical Committee Environmental Engineering (EE).
The present document is part 2, sub-part 0 of a multi-part deliverable covering environmental conditions and
environmental tests for telecommunications equipment, as identified below:
Part 1: "Classification of environmental conditions";
Part 2: "Specification of environmental tests";
Sub-part 0: "Introduction";
Sub-part 1: "Storage";
Sub-part 2: "Transportation";
Sub-part 3: "Stationary use at weatherprotected locations";
Sub-part 4: "Stationary use at non-weatherprotected locations";
Sub-part 5: "Ground vehicle installations";
Sub-part 6: "Ship environments";
Sub-part 7: "Portable and non-stationary use";
Sub-part 8: "Stationary use at underground locations".
Part 1 specifies different standardized environmental classes covering climatic, biological, chemically and mechanically
active substances, and mechanical conditions during storage, transportation and in use.
Part 2 specifies the test severities, test methods and performance criteria for the different environmental classes.

ETSI
5 ETSI EN 300 019-2-0 V2.2.1 (2022-08)
National transposition dates
Date of adoption of this EN: 9 August 2022
Date of latest announcement of this EN (doa): 30 November 2022
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 May 2023
Date of withdrawal of any conflicting National Standard (dow): 31 May 2023

Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.

ETSI
6 ETSI EN 300 019-2-0 V2.2.1 (2022-08)
1 Scope
The present document specifies the test severities and methods for verification of the required resistibility for equipment
which is to be stored, transported and used in the environments which characteristics are defined in ETSI
EN 300 019-1 [2].
The purpose of the present document is to provide a general overview of ETSI EN 300 019-2 [3].
ETSI TR 100 035 [i.1] should be used in conjunction with ETSI EN 300 019 multi-parts deliverable [2] and [3]. It gives
an introduction to the main concepts of environmental engineering, the purpose and use of environmental classes and
the corresponding test philosophy.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] ETSI EN 300 019-1-0: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 1-0: Classification of environmental
conditions; Introduction".
[2] ETSI EN 300 019-1 (all sub-parts): "Environmental Engineering (EE); Environmental conditions
and environmental tests for telecommunications equipment; Part 1: Classification of
environmental conditions".
[3] ETSI EN 300 019-2 (all sub-parts): "Environmental Engineering (EE); Environmental conditions
and environmental tests for telecommunications equipment; Part 2: Specification of environmental
tests".
[4] Void.
[5] IEC 60068-2 series: "Environmental testing".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While an
...