iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

oSIST prEN 17670-1:2021

(Main)

Plastics piping systems for non-pressure underground conveyance and storage of non-potable water - Manholes, inspection chambers and road gullies for storm water systems made of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1: Specifications for storm water manholes and inspection chambers)

Plastics piping systems for non-pressure underground conveyance and storage of non-potable water - Manholes, inspection chambers and road gullies for storm water systems made of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1: Specifications for storm water manholes and inspection chambers)

This document specifies the definitions and requirements for unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP), polypropylene with mineral modifier (PP-MD) or polyethylene (PE) storm water manholes and storm water inspection chambers intended for non-pressure use only in storm water systems to a maximum depth of 6 m from ground level to the lowest point of the storm water manhole or inspection chamber.
NOTE 1   Products complying with EN 13598-2 may also be used for storm water systems dependent on the requirement of the storm water system.
Storm water manholes and inspection chambers complying with this document are intended to be used in pedestrian or vehicular traffic areas outside the building structure.
NOTE 2   Products complying with this document can also be used in non-traffic areas.
Storm water manholes and inspection chambers complying with this document are made from a prescribed set of components that are manufactured from unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP), polypropylene with mineral modifier (PP-MD) or polyethylene (PE) and assembled together.
Storm water manholes and inspection chambers complying with this document may be equipped with optional devices (e.g. removable sand or silt bucket, flow regulators, ventilation parts, etc.), however the performance of these optional devices is not covered within the scope of this document.
NOTE 3    Products complying with this standard can be installed in underground applications without additional static calculation.
NOTE 4   The complete Storm water manhole or inspection chamber assembly can also include items which are not covered by this document (for example near surface or surface components).
NOTE 5   Storm water manholes and inspection chambers can be supplied with covers, frame covers and gratings complying with the relevant part of EN 124 [1].
Storm water manhole and inspection chamber components can be manufactured by various methods e.g. extrusion, injection moulding, rotational moulding, low-pressure moulding or fabricated.
NOTE 6   Storm water manholes and inspection chambers can be site assembled from different components, but can also be manufactured as a single unit.
NOTE 7   Storm water manholes and inspection chambers can be subject to national regulations and / or local provisions.

Kunststoff-Rohrleitungssysteme für die drucklose unterirdische Entwässerung und Speicherung für Nicht-Trinkwasser - Einsteigschächte, Kontrollschächte und Straßenabläufe für Regenwasserabflusssysteme aus weichmacherfreiem Polyvinylchlorid (PVC U), Polypropylen (PP) und Polyethylen (PE) - Teil 1: Anforderungen für Regenwasserabfluss-Einsteig- und -Kontrollschächte

Dieses Dokument legt die Begriffe und Anforderungen für Regenwasserabfluss-Einsteig- und  Kontrollschächte aus weichmacherfreiem Polyvinylchlorid (PVC U), Polypropylen (PP), Polypropylen mit mineralischen Additiven (PP MD) und Polyethylen (PE) fest, die ausschließlich für die Verwendung in drucklosen Regenwasserabflusssystemen bis zu einer Tiefe von höchstens 6 m ab Geländeoberkante bis zum tiefsten Punkt des Einsteigschachts oder Kontrollschachts vorgesehen sind.
ANMERKUNG 1   Produkte, die EN 13598 2 entsprechen, können je nach Anforderung des entsprechenden Systems auch in Regenwasserabflusssystemen verwendet werden.
Regenwasserabfluss-Einsteig- und -Kontrollschächte, die diesem Dokument entsprechen, sind für die Verwendung in Bereichen mit Fußgänger  und Fahrzeugverkehr außerhalb von Gebäudestrukturen vorgesehen.
ANMERKUNG 2   Produkte, die diesem Dokument entsprechen, können auch in Bereichen ohne Verkehr verwendet werden.
Regenwasserabfluss-Einsteig- und -Kontrollschächte, die diesem Dokument entsprechen, sind aus einer Reihe vorgeschriebener Bauteile gefertigt, die aus weichmacherfreiem Polyvinylchlorid (PVC U), Polypropylen (PP), Polypropylen mit mineralischen Additiven (PP MD) oder Polyethylen (PE) hergestellt und zusammengebaut sind.
Regenwasserabfluss-Einsteig- und -Kontrollschächte, die diesem Dokument entsprechen, dürfen mit optionalen Vorrichtungen (z. B. entfernbarem Sand  oder Schlammfang, Durchflussregler, Belüftungs-bauteilen usw.) ausgestattet sein; die Leistung dieser optionalen Vorrichtungen ist jedoch nicht vom Anwendungsbereich dieses Dokuments abgedeckt.
ANMERKUNG 3   Produkte, die dieser Norm entsprechen, können ohne zusätzliche statische Berechnung in erdverlegte Anwendungen eingebaut werden.
ANMERKUNG 4   Die vollständige Bauteilkombination des Regenwasserabfluss-Einsteig- oder -Kontrollschachts kann auch Elemente enthalten, die nicht von diesem Dokument abgedeckt werden (z. B. oberflächennahe Bauteile oder Oberflächenbauteile).
ANMERKUNG 5   Regenwasserabfluss-Einsteig- und -Kontrollschächte können mit Abdeckungen, Rahmen-abdeckungen und Rosten geliefert werden, die dem anwendbaren Teil von EN 124 [1] entsprechen.
Bauteile für Regenwasserabfluss-Einsteig- und- Kontrollschächte können mit verschiedenen Verfahren (z. B. Strangpressen, Spritzgießen, Rotationsgießen, Niederdruckgießen) hergestellt oder gefertigt sein.
ANMERKUNG 6   Regenwasserabfluss-Einsteig- und -Kontrollschächte können vor Ort aus verschiedenen Bauteilen montiert oder als einzelne Einheit gefertigt werden.
ANMERKUNG 7   Regenwasserabfluss-Einsteig- und -Kontrollschächte können nationalen Vorschriften und/oder örtlichen Regelungen unterliegen.

Systèmes de canalisations en plastique pour le transport et le stockage souterrains sans pression de l’eau non potable - Regards, boîtes d’inspection et de branchement et bouches d'égout pour les réseaux d’eaux pluviales en poly(chlorure de vinyle) non plastifié (PVC-U), en polypropylène (PP) et en polyéthylène (PE) - Partie 1 : Spécifications relatives aux regards et aux boîtes d’inspection et de branchement pour les eaux pluviales

Le présent document spécifie les définitions et les exigences relatives aux regards et aux boîtes d’inspection et de branchement pour eaux pluviales en poly(chlorure de vinyle) non plastifié (PVC-U), en polypropylène (PP), en polypropylène avec modificateurs minéraux (PP-MD) ou en polyéthylène (PE), destinés uniquement aux réseaux d’eaux pluviales sans pression enterrés jusqu’à une profondeur maximale de 6 m du niveau du sol au point le plus bas du regard ou de la boîte d’inspection et de branchement pour eaux pluviales.
NOTE 1   Les produits conformes à l’EN 13598-2 peuvent aussi être utilisés pour les réseaux d’eaux pluviales en fonction des exigences applicables au réseau concerné.
Les regards et les boîtes d’inspection et de branchement pour eaux pluviales conformes au présent document sont destinés à être utilisés dans les zones de circulation de piétons ou de véhicules à l’extérieur de la structure du bâtiment.
NOTE 2   Les produits conformes au présent document peuvent également être utilisés dans des zones sans circulation.
Les regards et les boîtes d’inspection et de branchement pour eaux pluviales conformes au présent document sont constitués d’un ensemble de composants prescrits qui sont fabriqués en poly(chlorure de vinyle) non plastifié (PVC-U), en polypropylène (PP), en polypropylène avec modificateurs minéraux (PP-MD) ou en polyéthylène (PE) et assemblés.
Les regards et les boîtes d’inspection et de branchement pour eaux pluviales conformes au présent document peuvent être équipés de dispositifs optionnels (par exemple panier décanteur amovible, régulateurs de débit, pièces de ventilation, etc.) ; cependant, les performances de ces dispositifs optionnels ne sont pas couvertes par le domaine d’application du présent document.
NOTE 3   Les produits conformes à la présente norme peuvent être mis en œuvre dans des applications enterrées sans calculs statiques supplémentaires.
NOTE 4   Le montage complet du regard ou de la boîte d’inspection et de branchement pour eaux pluviales peut également inclure des éléments non couverts par le présent document (par exemple, des composants supérieurs ou de surface).
NOTE 5   Les regards et les boîtes d’inspection et de branchement pour eaux pluviales peuvent être fournis avec des tampons, des tampons avec cadre et des grilles conformes à la partie applicable de l’EN 124 [1].
Les composants du regard et de la boîte d’inspection et de branchement pour eaux pluviales peuvent être fabriqués selon diverses méthodes, à savoir : par extrusion, moulage par injection, moulage par rotation, moulage à basse pression ou être façonnés.
NOTE 6   Les regards et les boîtes d’inspection et de branchement pour eaux pluviales peuvent être assemblés sur site à partir de différents éléments, mais ils peuvent également être fabriqués en un seul élément.
NOTE 7   Les regards et les boîtes d’inspection et de branchement pour eaux pluviales peuvent être soumis aux réglementations nationales et/ou aux dispositions locales.

Cevni sistemi iz polimernih materialov, ki delujejo po težnostnem principu in so položeni v zemljo, za transport in shranjevanje vode, ki ni namenjena pitju - Vstopni in revizijski jaški ter cestni odtoki za meteorno vodo iz neplastificiranega poli(vinilklorida) (PVC-U), polipropilena (PP) in polietilena (PE ) - 1. del: Specifikacije za odtoke meteorne vode in revizijske jaške

General Information

Status
Not Published
Public Enquiry End Date
02-Aug-2021
ICS
23.040.20 - Plastics pipes
93.030 - External sewage systems
Technical Committee
PCV - Plastic pipes, fittings and valves
Current Stage
98 - Abandoned project (Adopted Project)
Start Date
23-Apr-2024
Due Date
28-Apr-2024
Completion Date
23-Apr-2024
Ref Project
prEN 17670-1 - Plastics piping systems for non-pressure underground conveyance and storage of non-potable water - Manholes, inspection chambers and road gullies for storm water systems made of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1: Specifications for storm water manholes and inspection chambers)

Buy Standard

prEN 17670-1:2021prEN 17670-1:2021
PreviousNext
Draft
prEN 17670-1:2021
English language
37 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN 17670-1:2021
01-julij-2021
Cevni sistemi iz polimernih materialov, ki delujejo po težnostnem principu in so
položeni v zemljo, za transport in shranjevanje vode, ki ni namenjena pitju -
Vstopni in revizijski jaški ter cestni odtoki za meteorno vodo iz neplastificiranega
poli(vinilklorida) (PVC-U), polipropilena (PP) in polietilena (PE ) - 1. del:
Specifikacije za odtoke meteorne vode in revizijske jaške
Plastics piping systems for non-pressure underground conveyance and storage of non-
potable water - Manholes, inspection chambers and road gullies for storm water systems
made of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene
(PE) - Part 1: Specifications for storm water manholes and inspection chambers)
Kunststoff-Rohrleitungssysteme für die drucklose unterirdische Entwässerung und
Speicherung für Nicht-Trinkwasser - Einsteigschächte, Kontrollschächte und
Straßenabläufe für Regenwasserabflusssysteme aus weichmacherfreiem
Polyvinylchlorid (PVC U), Polypropylen (PP) und Polyethylen (PE) - Teil 1:
Anforderungen für Regenwasserabfluss-Einsteig- und -Kontrollschächte
Systèmes de canalisations en plastique pour le transport et le stockage souterrains sans
pression de l’eau non potable - Regards, boîtes d’inspection et de branchement et
bouches d'égout pour les réseaux d’eaux pluviales en poly(chlorure de vinyle) non
plastifié (PVC-U), en polypropylène (PP) et en polyéthylène (PE) - Partie 1 :
Spécifications relatives aux regards et aux boîtes d’inspection et de branchement pour
les eaux pluviales
Ta slovenski standard je istoveten z: prEN 17670-1
oSIST prEN 17670-1:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 17670-1:2021

---------------------- Page: 2 ----------------------
oSIST prEN 17670-1:2021


DRAFT
EUROPEAN STANDARD
prEN 17670-1
NORME EUROPÉENNE

EUROPÄISCHE NORM

May 2021
ICS 23.040.20; 93.030
English Version

Plastics piping systems for non-pressure underground
conveyance and storage of non-potable water - Manholes,
inspection chambers and road gullies for storm water
systems made of unplasticized poly(vinyl chloride) (PVC-
U), polypropylene (PP) and polyethylene (PE) - Part 1:
Specifications for storm water manholes and inspection
chambers)
Systèmes de canalisations en plastique pour le Kunststoff-Rohrleitungssysteme für die drucklose
transport et le stockage souterrains sans pression de unterirdische Entwässerung und Speicherung für
l'eau non potable - Regards, boîtes d'inspection et de Nicht-Trinkwasser - Einsteigschächte,
branchement et bouches d'égout pour les réseaux Kontrollschächte und Straßenabläufe für
d'eaux pluviales en poly(chlorure de vinyle) non Regenwasserabflusssysteme aus weichmacherfreiem
plastifié (PVC-U), en polypropylène (PP) et en Polyvinylchlorid (PVC U), Polypropylen (PP) und
polyéthylène (PE) - Partie 1 : Spécifications relatives Polyethylen (PE) - Teil 1: Anforderungen für
aux regards et aux boîtes d'inspection et de Regenwasserabfluss-Einsteig- und -Kontrollschächte
branchement pour les eaux pluviales
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 155.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 17670
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 12201-5:2024(Main)
Plastics piping systems for water supply, and for drains and sewers under pressure - Polyethylene (PE) - Part 5: Fitness for purpose of the system
EN 12201-5:2024

This document specifies the characteristics of the fitness for purpose of the assembled piping systems intended for the conveyance of water intended for human consumption, raw water prior to treatment, drainage and sewerage under pressure, vacuum sewer systems, and water for other purposes.
It also specifies the method of preparation of test piece joints, and the tests to be carried out on these joints for assessing the fitness for purpose of the system under normal and extreme conditions.
NOTE 1   For PE components intended for the conveyance of water for human consumption and raw water prior to treatment attention is drawn to the introduction of this document. Components manufactured for water for other purposes are possibly not suitable for water supply for human consumption.
It specifies the test parameters for the test methods referred to in this document.
NOTE 2   This document is intended only to be used by the product manufacturer to assess the performance of components according to prEN 12201 2, prEN 12201 3, or prEN 12201 4 when joined together under normal and extreme conditions. It is not intended for on-site testing of pipe systems.
In conjunction with Parts 1 to 4 of prEN 12201 it is applicable to PE pipes, fittings, valves, their joints and to joints with components of other materials intended to be used under the following conditions:
a)   allowable operating pressure, PFA, up to 25 bar );
b)   an operating temperature of 20 °C as a reference temperature for design purposes;
c)   buried in the ground;
d)   sea outfalls;
e)   laid in water;
f)   above ground, including pipes suspended below bridges.
NOTE 3   For applications operating at constant temperatures greater than 20 °C up to 40 °C, see prEN 12201 1:2021, Annex A.
The EN 12201 series covers a range of allowable operating pressures and gives requirements concerning colours.
NOTE 4   It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national guidance or regulations and installation practices or codes.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 12201-1:2024(Main)
Plastics piping systems for water supply, and for drains and sewers under pressure - Polyethylene (PE) - Part 1: General
EN 12201-1:2024

This document specifies materials and the general aspects of polyethylene (PE) pressure piping systems (mains and service pipes) for buried or above ground applications, intended for the conveyance of water for human consumption, raw water prior to treatment, drains and sewers under pressure, vacuum sewer systems, and water for other purposes, with the exception of industrial application.
NOTE 1   For PE components intended for the conveyance of water intended for human consumption and raw water prior to treatment attention is drawn to Clause 6 of this document. Components manufactured for water for other purposes, drains and sewers, and vacuum systems are possibly not suitable for water supply for human consumption.
NOTE 2   Industrial application is covered by EN ISO 15494 [6].
The intended use includes sea outfalls, laid in water and pipes suspended below bridges.
It also specifies the test parameters for the test methods referred to in this document.
In conjunction with EN 12201-2, EN 12201 3, EN 12201 4 and EN 12201 5, this document is applicable to PE pipes, fittings and valves, their joints and joints with components of PE and other materials intended to be used under the following conditions:
a)   allowable operating pressure, PFA, up to 25 bar  ;
b)   an operating temperature of 20 °C as a reference temperature.
NOTE 3   For applications operating at constant temperatures greater than 20 °C and up to and including 50 °C, see Annex A.
The EN 12201 series covers a range of allowable operating pressures and gives requirements concerning colours.
NOTE 4   It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national guidance or regulations and installation practices or codes.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 12201-3:2024(Main)
Plastics piping systems for water supply, and for drains and sewers under pressure - Polyethylene (PE) - Part 3: Fittings
EN 12201-3:2024

This document specifies the characteristics of fittings made from polyethylene (PE) for buried and above ground applications, intended for the conveyance of water for human consumption, raw water prior to treatment, drainage and sewerage under pressure, vacuum sewer systems, and water for other purposes.
NOTE 1   For PE components intended for the conveyance of water for human consumption and raw water prior to treatment, attention is drawn to 6.6 of this document. Components manufactured for water for other purposes, drainage and sewerage are possibly not suitable for water supply for human consumption.
It also specifies the test parameters for the test methods referred to in this document.
In conjunction with Parts 1, 2, 4 and 5 of EN 12201, it is applicable to PE fittings, their joints and to joints with components of PE and other materials intended to be used under the following conditions:
a)   allowable operating pressure, PFA, up to 25 bar  );
b)   an operating temperature of 20 °C as a reference temperature;
c)   buried in the ground;
d)   sea outfalls;
e)   laid in water;
f)   above ground, including pipes suspended below bridges.
NOTE 2   For applications operating at constant temperature greater than 20 °C and up to 40 °C, see prEN 12201 1:2021, Annex A.
The EN 12201 series covers a range of allowable operating pressures and gives requirements concerning colours.
NOTE 3   It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national guidance or regulations and installation practices or codes.
These fittings can be of the following types:
a)   fusion fittings;
1)   electrofusion fittings;
2)   spigot end fittings (for butt fusion using heated tools and electrofusion socket fusion);
3)   socket fusion fittings (see Annex A);
b)   mechanical fittings;
1)   compression fittings;
2)   flanged fittings;
c)   fabricated fittings (see Annex B).

  • Standard
    43 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 12201-2:2024(Main)
Plastics piping systems for water supply, and for drains and sewers under pressure - Polyethylene (PE) - Part 2: Pipes
EN 12201-2:2024

This document specifies the characteristics of pipes made from polyethylene (PE) for buried and above ground applications, intended for the conveyance of water for human consumption, raw water prior to treatment, drainage and sewerage under pressure, vacuum sewer systems, and water for other purposes.
NOTE 1   For PE components intended for the conveyance of water for human consumption and raw water prior to treatment attention is drawn to 6.3 of this document. Components manufactured for water for general purposes, drainage and sewerage are possibly not suitable for water supply for human consumption.
For use in contaminated soils special consideration is taken for pipes intended for the transport of water intended for human consumption or raw water prior to treatment.
NOTE 2   Pipes constructions including barrier layers are not covered by this document. ISO 21004 provides an alternative solution for use in contaminated soils [9].
It also specifies the test parameters for the test methods referred to in this document.
In conjunction with Part 1 and Parts 3 to 5 of EN 12201, it is applicable to PE pipes, their joints and to joints with components of PE and other materials intended to be used under the following conditions:
a)   allowable operating pressure, PFA, up to 25 bar  );
b)   an operating temperature of 20 °C as a reference temperature;
c)   buried in the ground;
d)   sea outfalls;
e)   laid in water;
f)   above ground, including pipes suspended below bridges.
NOTE 3   For applications operating at constant temperatures greater than 20 °C and up to 40 °C, see prEN 12201-1:2021, Annex A
EN 12201 series covers a range of allowable operating pressures and gives requirements concerning colours.
This document specifies three types of pipe:
—   PE pipes (outside diameter dn) including any identification stripes;
—   PE pipes with co-extruded layers on either or both the outside and/or inside of the pipe (total outside diameter dn) as specified in Annex B, where all layers have the same MRS rating. A coextruded pipe made of a combination of PE 100 and PE 100-RC layers are regarded as PE 100 and marked accordingly.
—   PE pipes (outside diameter dn) with a peelable, contiguous thermoplastics additional layer on the outside of the pipe (‘coated pipe’) as specified in Annex C.
NOTE 4   It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national guidance or regulations and installation practices or codes.
NOTE 5   Assessment of the resistance to slow crack growth of the PE pipe compound used for the manufacture of products to this document is required in accordance with prEN 12201-1:2021, Table 2.

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 12201-4:2024(Main)
Plastics piping systems for water supply, and for drains and sewers under pressure - Polyethylene (PE) - Part 4: Valves for water supply systems
EN 12201-4:2024

This document specifies the characteristics of valves or valve bodies made from polyethylene (PE) for buried and above ground applications, intended for the conveyance of water for human consumption, raw water prior to treatment, drainage and sewerage under pressure, vacuum sewer systems, and water for other purposes.
It is applicable to isolating unidirectional and bi-directional valves with spigot ends or electrofusion sockets intended to be fused with PE pipes or fittings conforming to prEN 12201 2 and prEN 12201 3 respectively.
Valves made from materials other than PE, designed for the supply of water, drainage and sewerage under pressure conforming to the relevant standards can be used in PE piping systems according to EN 12201, provided that they have PE connections for butt fusion or electrofusion ends, including integrated material transition joints, conforming to prEN 12201 3.
NOTE 1   For valves or valve bodies intended for drainage and sewerage under pressure, additional specifications/tests could be necessary according to the requirements of the purchaser, especially for the chemical resistance of the components in contact with the fluids and functioning characteristics.
NOTE 2   For PE components intended for the conveyance of water for human consumption and raw water prior to treatment attention is drawn to 5.4. Components manufactured for water for other purposes are possibly not suitable for water supply for human consumption.
It also specifies the test parameters for the test methods referred to in this document.
NOTE 3   Valves made from material other than polyethylene (PE) designed for the supply of water intended for human consumption to a relevant standard(s) can be used in PE piping systems conforming to EN 12201 when they have relevant PE connection for butt fusion or electrofusion ends (see prEN 12201 3:2021).
In conjunction with Parts 1, 2, 3 and 5 of EN 12201 it is applicable to PE valves, their joints and to joints with components of PE and other materials intended to be used under the following conditions:
a)   allowable operating pressure, PFA, up to 25 bar );
b)   an operating temperature of 20 °C as a reference temperature;
c)   buried in the ground;
d)   sea outfalls;
e)   laid in water;
f)   above ground, including pipes suspended below bridges.
NOTE 4   For applications operating at constant temperature greater than 20 °C and up to 40 °C, see prEN 12201 1:2021, Annex A.
EN 12201 covers a range of allowable operating pressures and gives requirements concerning colours and additives.
NOTE 5   It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national guidance or regulations and installation practices or codes.
This Part of EN 12201 covers valves for pipes with a nominal outside diameter dn ≤ 400 mm.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 17670-2:2024(Main)
Plastics piping systems for non-pressure underground conveyance of surface water - Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 2: Specification for road gullies
EN 17670-2:2023

This document specifies the definitions and requirements for unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP), polypropylene with mineral modifier (PP-MD) or polyethylene (PE) storm water road gullies intended for non-pressure use only in storm water and combined systems installed to a maximum depth of 4 m from ground level to the lowest point of the storm water road gully.
Storm water road gullies complying with this document are intended to be used in pedestrian or vehicular traffic areas outside the building structure.
NOTE 1   Products complying with this document can also be used in non-traffic areas.
NOTE 2   Storm water road gullies may be subject to national regulation which limit the maximum installation depth and / or local provisions. The installer should check for compliance prior to installation.
Storm water road gullies complying with this document are made from a prescribed set of components that are manufactured from unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP), polypropylene with mineral modifier (PP-MD) or polyethylene (PE) and assembled together.
Storm water road gullies complying with this document may be equipped with optional devices (e.g. removable sand or silt bucket, leaf separator etc.), however the performance of these optional devices is not covered within the scope of this document.
Storm water road gully components can be manufactured by various methods e.g. extrusion, injection moulding, rotational moulding, low-pressure moulding, blow moulding, thermoforming or fabricated.
NOTE 3   Products complying with this standard can be installed in underground applications without additional static calculation
NOTE 4   The complete storm water road gully assembly can also include items non-plastic items (near surface or surface components for example) which are not covered by this document.
NOTE 5   The complete storm water road gully assembly can be supplied with covers, frame covers and gratings complying with the relevant part of EN 124 [1] which are not covered by this document. However, reference should be made to this document for geometrical characteristics where applicable.
NOTE 6   Storm water road gullies can be site assembled from different components, but can also be manufactured as a single unit.
-   storm water road gullies with or without sand / silt trap;
-   storm water road gullies with or without water seal preventing odour release;
-   storm water road gullies where the traffic load will or will not be carried by the complete gully (resp. "Direct loaded storm water gullies" or "Indirect loaded storm water gullies").

  • Standard
    49 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 13267:2023(Main)
Thermoplastics piping systems for non-pressure underground drainage and sewerage - Thermoplastics inspection chamber and manhole bases - Test methods for buckling resistance (ISO 13267:2022)
EN ISO 13267:2023

This document specifies methods of test for the resistance of the base of thermoplastics inspection chambers and manholes to external soil and ground-water pressure after installation.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 13268:2023(Main)
Thermoplastics piping systems for non-pressure underground drainage and sewerage - Thermoplastics shafts or risers for inspection chambers and manholes - Determination of ring stiffness (ISO 13268:2022)
EN ISO 13268:2023

This document specifies a test method for assessing the initial (short-term) tangential ring stiffness of riser shafts for thermoplastics inspection chambers or manholes.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 13266:2023(Main)
Thermoplastics piping systems for non-pressure underground drainage and sewerage - Thermoplastics shafts or risers for inspection chambers and manholes - Determination of resistance against surface and traffic loading (ISO 13266:2022)
EN ISO 13266:2023

This document specifies a method of testing the resistance of the upper assembly of inspection chambers and manhole components against surface and traffic loading.
It is not applicable to requirements for testing the cover and frame. Those requirements are specified in EN 124-1 or other standards, depending on the material.
NOTE    Upper assembly components normally include shafts or risers, cones, telescopic adapters and near surface components.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 17176-2:2019+A1:2022(Main)
Plastics piping systems for water supply and for buried and above ground drainage, sewerage and irrigation under pressure - Oriented unplasticized poly(vinyl chloride) (PVC-O) - Part 2: Pipes
EN 17176-2:2019+A1:2022

This part of FprEN 17176 specifies the characteristics of solid-wall pipes made of oriented unplasticized poly(vinyl chloride) (PVC-O) for piping systems intended for water supply and for buried drainage, sewerage, treated waste water and irrigation under pressure or above-ground where protected from direct sunlight. It also specifies the test parameters for the test methods referred to in this document.
In conjunction with FprEN 17176-1 and FprEN 17176-5, it is applicable to oriented PVC-O pipes with or without integral socket intended to be used for the following:
a)   water mains and services lines;
b)   conveyance of water for both outside and inside buildings;
c)   drainage, sewerage and treated waste water under pressure;
d)   irrigation under pressure.
It is applicable to piping systems intended for the supply of water with a maximum allowable operating pressure (PFA) up to and including 25 bar  . The piping system according to this document is intended for the conveyance of cold water up to and including 45 °C and especially in those applications where special performance requirements are needed, such as impact loads and pressure fluctuations.
For temperatures between 25 °C and 45 °C, Figure C.1 of this document applies.
This part of FprEN 17176 specifies a range of pipe sizes and pressure classes and gives a requirement and recommendations concerning colours.
NOTE   It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day