SIST EN 13170:2013+A1:2015/oprA2:2018
(Amendment)Thermal insulation products for buildings - Factory made products of expanded cork (ICB) - Specification
Thermal insulation products for buildings - Factory made products of expanded cork (ICB) - Specification
DOW = DAV + 21 months
Wärmedämmstoffe für Gebäude - Werkmäßig hergestellte Produkte aus expandiertem Kork (ICB) - Spezifikation
Produits isolants thermiques pour le bâtiment - Produits manufacturés en liège expansé (ICB) - Spécification
Toplotnoizolacijski proizvodi za stavbe - Proizvodi iz ekspandirane plute (ICB) - Specifikacija
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 13170:2013+A1:2015/oprA2:2018
01-november-2018
Toplotnoizolacijski proizvodi za stavbe - Proizvodi iz ekspandirane plute (ICB) -
Specifikacija
Thermal insulation products for buildings - Factory made products of expanded cork
(ICB) - Specification
Wärmedämmstoffe für Gebäude - Werkmäßig hergestellte Produkte aus expandiertem
Kork (ICB) - Spezifikation
Produits isolants thermiques pour le bâtiment - Produits manufacturés en liège expansé
(ICB) - Spécification
Ta slovenski standard je istoveten z: EN 13170:2012+A1:2015/prA2
ICS:
91.100.60 0DWHULDOL]DWRSORWQRLQ Thermal and sound insulating
]YRþQRL]RODFLMR materials
SIST EN en,fr,de
13170:2013+A1:2015/oprA2:2018
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 13170:2013+A1:2015/oprA2:2018
---------------------- Page: 2 ----------------------
SIST EN 13170:2013+A1:2015/oprA2:2018
DRAFT
EUROPEAN STANDARD
EN 13170:2012+A1:2015
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA2
September 2018
ICS 91.100.60
English Version
Thermal insulation products for buildings - Factory made
products of expanded cork (ICB) - Specification
Produits isolants thermiques pour le bâtiment - Wärmedämmstoffe für Gebäude - Werkmäßig
Produits manufacturés en liège expansé (ICB) - hergestellte Produkte aus expandiertem Kork (ICB) -
Spécification Spezifikation
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 88.
This draft amendment A2, if approved, will modify the European Standard EN 13170:2012+A1:2015. If this draft becomes an
amendment, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for
inclusion of this amendment into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13170:2012+A1:2015/prA2:2018 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 13170:2013+A1:2015/oprA2:2018
EN 13170:2012+A1:2015/prA2:2018 (E)
Contents Page
European foreword . 3
1 Modification to the European foreword . 4
2 Modification to the Scope . 4
3 Modification to Clause 2, Normative references . 4
4 Modification to Clause 3, Terms, definitions, symbols, units and abbreviated terms . 5
5 Modification to Clause 4, Requirements . 5
6 Modification to 4.2.9, Apparent density . 5
7 Modification to 4.3.3, Compressive stress or compressive strength . 5
8 Modification to 4.3.4 , Tensile strength perpendicular to faces . 6
9 Modification to 4.3.7, Short term water absorption . 6
10 Modification to 4.3.13, Release of dangerous substances . 6
11 Modification to 4.3.15, Continuous glowing combustion . 7
12 Modification to 5.3.2, Thermal resistance and thermal conductivity . 7
13 Modification to Clause 6, Designation code . 9
14 Modification to Clause 7, Type testing (TT) and factory production control (FPC) . 10
15 Modification to Annex ZA, Clauses of this European Standard addressing the
provisions of the EU Construction Products Regulation . 11
2
---------------------- Page: 4 ----------------------
SIST EN 13170:2013+A1:2015/oprA2:2018
EN 13170:2012+A1:2015/prA2:2018 (E)
European foreword
This document (EN 13170:2012+A1:2015/prA2:2018) has been prepared by Technical Committee
CEN/TC 88 “Thermal insulating materials and products”, the secretariat of which is held by DIN.
This document is currently submitted to the CEN Enquiry.
This document has been prepared under a standardization request given to CEN by the European
Commission and the European Free Trade Association.
For relationship with EU Regulation, see informative Annex ZA which is an integral part of this
document.
3
---------------------- Page: 5 ----------------------
SIST EN 13170:2013+A1:2015/oprA2:2018
EN 13170:2012+A1:2015/prA2:2018 (E)
1 Modification to the European foreword
In the fifth paragraph, delete ", and supports essential requirements of EU Directive(s)."
Delete the ninth paragraph (list of changes) and replace the tenth and eleventh paragraph with the
following:
"Amendment A2 modifies EN 13170:2012 and its A1 amendment. This amendment introduces or
corrects:
a) Modified the clause "Apparent density” (4.2.9);
b) Modified the clause "Compressive stress or compressive strength” (4.3.3);
c) Modified the clause "Tensile strength perpendicular to faces” (4.3.4);
d) Modified the clause "Short term water absorption” (4.3.7);
e) Introduced the clause "Continuous smouldering";
f) Modified the clause "Release of Dangerous substance";
g) Modified the definition for "class F" in the clause "reaction to fire";
h) Editorial modifications in different parts of the text and linked to the above modification;
i) Modifications to be in line with the CPR, e.g. PTD replaced by TT ;
j) Modified the Annex ZA.".
In the fourteenth paragraph, add the following standard to the end of the list of standards:
"EN 16069, Thermal insulation products for buildings — Factory made products of polyethylene foam
(PEF) — Specification"
2 Modification to the Scope
Replace the first sentence with:
"This European Standard specifies the characteristics for factory made products of expanded cork,
which are used for the thermal insulation of buildings.".
Replace the third paragraph with:
"This standard describes product characteristics and includes procedures for testing, assessment and
verification of constancy of performance (AVCP), marking and labelling.".
3 Modification to Clause 2, Normative references
Add the following references:
"EN 16516, Construction products — Assessment of release of dangerous substances — Determination of
emissions into indoor air
EN 16733:2016, Reaction to fire tests for building products — Determination of a building product's
propensity to undergo continuous smouldering".
4
---------------------- Page: 6 ----------------------
SIST EN 13170:2013+A1:2015/oprA2:2018
EN 13170:2012+A1:2015/prA2:2018 (E)
4 Modification to Clause 3, Terms, definitions, symbols, units and abbreviated
terms
Delete the terms and definition for "3.1.4 level" and "3.1.5 class" and modify the numbers of the remaining
terms accordingly.
Add the following symbols:
"
S–NoS is the Continuous Smouldering declaration (NoS means no Smouldering and S means
Smouldering)
ANP Smouldering assessment not possible
".
Delete the following abbreviated terms:
PTD is Product Type Determination (previously named ITT for Initial Type Test)
VCP is Verification of Constancy of Performance (previously named evaluation of conformity)
Add the following abbreviated term:
"
TT is Type Testing
".
5 Modification to Clause 4, Requirements
In the title, replace “Requirements” with”Characteristics”.
6 Modification to 4.2.9, Apparent density
Replace the text in the clause with the following:
"Apparent density, ρ , shall be determined in accordance with EN 1602. The product shall be protected
a
from rain during storage.".
7 Modification to 4.3.3, Compressive stress or compressive strength
Replace Table 6 with the following:
"Table 6 — Levels for compressive stress at 10 % deformation
Requirement
Level
kPa
CS(10)90 ≥ 90
CS(10)100 ≥ 100
CS(10)110 ≥ 110
CS(10)120 ≥ 120
CS(10)150 ≥ 150
CS(10)200 ≥ 200
CS(10)220 ≥ 220
CS(10)250 ≥ 250
5
---------------------- Page: 7 ----------------------
SIST EN 13170:2013+A1:2015/oprA2:2018
EN 13170:2012+A1:2015/prA2:2018 (E)
".
8 Modification to 4.3.4 , Tensile strength perpendicular to faces
Replace Table 7 with the following:
"Table 7 — Levels for tensile strength perpendicular to faces
Requirement
Level
kPa
TR30 ≥ 30
TR40 ≥ 40
TR50 ≥ 50
TR60 ≥ 60
TR70 ≥ 70
TR80 ≥ 80
".
9 Modification to 4.3.7, Short term water absorption
Replace the table with the following:
"
Level Requirement
2
kg/m
WS0,2 ≤ 0,2
WS0,3 ≤ 0,3
WS0,4 ≤ 0,4
WS0,5 ≤ 0,5
".
10 Modification to 4.3.13, Release of dangerous substances
Replace the text in the clause with the following:
1)
"If the release of dangerous substances into indoor air is tested, this shall be done according to
EN 16516.
NOTE An informative database covering European and national provisions on dangerous substances is
available at the Construction web site on EUROPA accessed through: http://ec.europa.eu/growth/tools-databases/cp-
ds.".
1) See for reference the LCI list of the European Commission "Agreed EU-LCI values"
(http://ec.europa.eu/growth/sectors/construction/eu-lci/values_en).
6
---------------------- Page: 8 ----------------------
SIST EN 13170:2013+A1:2015/oprA2:2018
EN 13170:2012+A1:2015/prA2:2018 (E)
11 Modification to 4.3.15, Continuous glowing combustion
Replace the current title of the clause with: "Propensity to undergo continuous smouldering".
Replace the text in the clause with the following:
"When declared the propensity to undergo continuous smouldering of expanded cork shall be tested
according to EN 16733. The following conditions and parameters shall be considered within the tests:
— density according to EN 1602;
— thickness to be determined by test according EN 823.
The test is intended for naked core products. Any facings or coatings are removed when preparing the
test specimen
The tests shall be done without consideration of the intended end-use conditions. If the paragraph 6.2.5
of EN 16733 applies, a permanent contact between the pieces shall be assured.
The results of tests considering the aforementioned parameters in fully are also valid for products:
— with equal or lower density up to a tested density of 115 kg/m³;
— if tested density is higher than 115 kg/m³, can be applicable to lower density if additionally tested
with a density of 100 kg/m³ (± 15 %);
— with lower thickness and also with higher thickness when 100 mm thick specimens were tested;
— with any facings or coatings or suchlike;
— for any end-use conditions.
If the test according to Clause 11 of EN 16733:2016 has been passed, declare: “the product does not
show propensity for continuous smouldering combustion”. If the test according to Clause 11 of
EN 16733:2016 has been failed, declare: “the product shows propensity for continuous smouldering
combustion”. If the assessment was not possible according to Clause 11 of EN 16733:2016, declare:
“assessment of the propensity for continuous smouldering combustion is not possible”.
If a Designation code is given, the following abbreviations shall be used:
— the product does not show propensity for continuous smouldering combustion: NoS
— the product shows propensity for continuous smouldering combustion: S
— the assessment of the propensity for continuous smouldering combustion is not possible: ANP".
12 Modification to 5.3.2, Thermal resistance and thermal conductivity
Replace Table 9 with the following:
7
---------------------- Page: 9 ----------------------
SIST EN 13170:2013+A1:2015/oprA2:2018
EN 13170:2012+A1:2015/prA2:2018 (E)
"Table 9 — Test methods, test specimens and conditions
Dimensions in millimetres
Clause Test Test specimen Minimum Specific
method length and number of conditions
a
width measurements
to get one test
result
No Title
4.2.1 Thermal EN 12667 See EN 12667 1 —
resistance — or EN 12939
EN 12939
thermal conductivity
4.2.2 Length and width EN 822 Full-size 3 —
4.2.3 Thickness EN 823 Full-size 3 Method B.2
pressure of
(250 ± 5) Pa
4.2.4 Squareness EN 824 Full-size 3 —
4.2.5 Flatness EN 825 Full-size 3 —
4.2.6 Reaction to fire of See EN 13501-1 and EN 15715 See Clause 5 of
the product as
EN 15715:2009
placed on the
market
4.2.8 Moisture content EN 12105 200 × 200 or 5 —
300 × 300 or
500 × 500
4.2.9 Apparent density EN 1602 Full size board 5 —
4.2.10 Bending strength EN 12089 150 × (5 × d ) Method B
5
N
4.3.2 Dimensional EN 1604 200 × 200 3 —
stability under
specified conditions
4.3.3 Compressive stress EN 826 100 × 100 3 —
at 10 % deformation
4.3.4 Tensile strength EN 1607 100 × 100 or 5 —
perpendicular to 200 × 200
faces
4.3.5 Point load EN 12430 300 × 300 3 —
4.3.6 Compressive creep EN 1606 100 × 100 3 —
4.3.7 Short term water EN 1609 200 × 200 3 Method A
absorption
4.3.8 b
Water vapour EN 12086 100 × 100 3
transmission
4.3.9 Dynamic stiffness EN 29052-1 200 × 200 3 —
8
---------------------- Page: 10 ----------------------
SIST EN 13170:2013+A1:2015/oprA2:2018
EN 13170:2012+A1:2015/prA2:2018 (E)
Clause Test Test specimen Minimum Specific
method length and number of conditions
a
width measurements
to get one test
result
No Title
4.3.10 Thickness, d Classes
L EN 12431
T1 and T2
Thickness, d
B
200 × 200 3
Long term thickness EN 1606 Level CP2
reduction
2
4.3.11 Sound absorption EN ISO 354 Minimum 10 m 1 To be reported
4.3.12 Air flow resistivity EN 29053 Apparatus 3 Method A
4.3.13 Release of
dangerous EN 16516 See EN 16516 See EN 16516 See EN 16516
substances
4.3.14 Reaction to fire of See EN 13501-1 and EN 15715 See Clause 6 of
the product in
EN 15715:2009
standardized
assemblies
simulating end-use
applications
4.3.15 Continuous glowing
combustion - EN 16733 see EN 16733 see EN 16733 see EN 16733
smoulde
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.