SIST EN 17333-5:2020
(Main)Characterization of One Component Foam - Part 5: Insulation
Characterization of One Component Foam - Part 5: Insulation
This document specifies test methods for the evaluation of the insulation properties for moisture curing, self-curing or water drying foams dispensed from single pressurized containers used as an insulating air sealant and adhesive for both building and non-building applications.
This document does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.
The following test method is described:
- Thermal conductivity: This method describes how to determine the long term thermal conductivity of a cured OCF foam, dispensed from a pressurized can, with a sample subjected to accelerated ageing procedure.
Charakterisierung von Einkomponentenschäumen - Teil 5: Dämmung
Dieses Dokument legt Prüfverfahren für die Beurteilung der Dämmeigenschaften von feuchtigkeits-härtenden, selbsthärtenden oder wassertrocknenden Schäumen fest, die aus einzelnen druckbeaufschlagten Behältern abgegeben werden und als dämmender Dichtstoff und Klebstoff sowohl für Bauanwendungen als auch andere Anwendungen verwendet werden.
Dieses Dokument beansprucht nicht, sämtliche mit seiner Anwendung verbundenen Sicherheitsprobleme, soweit diese gegeben sind, zu behandeln. Es liegt in der Verantwortung des Anwenders dieser Norm, angemessene Maßnahmen in Bezug auf den Gesundheits und Arbeitsschutz einzuleiten und die Anwendbarkeit gesetzlicher Anforderungen vor ihrer Anwendung zu ermitteln.
Das folgende Prüfverfahren wird beschrieben:
- Wärmeleitfähigkeit: Dieses Verfahren beschreibt, wie die Langzeit Wärmeleitfähigkeit eines ausgehärteten OCF zu bestimmen ist, der aus einer Druckdose abgegeben wird, wobei eine Probe dem Verfahren der beschleunigten Alterung unterzogen wird.
Caractérisation des mousses monocomposants - Partie 5 : Isolation
Le présent document spécifie des méthodes d’essai permettant d’évaluer les caractéristiques d’isolation des mousses durcissant à l’humidité, des mousses autopolymérisables et des mousses séchant dans l’eau, appliquées à partir de récipients individuels sous pression, utilisées en tant que joint d’étanchéité à l’air et en tant qu’adhésif pour les applications du génie civil et autres.
Le présent document ne prétend pas aborder la totalité des problèmes de sécurité qui pourraient découler de son utilisation. Il est de la responsabilité de l’utilisateur de la présente norme de respecter des pratiques de sécurité et de santé appropriées et de déterminer l’applicabilité des exigences réglementaires avant son utilisation.
La méthode d’essai suivante est décrite :
- conductivité thermique : cette méthode permet de déterminer la conductivité thermique à long terme d’une mousse monocomposant durcie, appliquée à partir d’un récipient individuel sous pression, avec un échantillon soumis à un mode opératoire de vieillissement accéléré.
Karakterizacija enokomponentnih pen - 5. del: Izolacija
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 17333-5:2020
01-junij-2020
Karakterizacija enokomponentnih pen - 5. del: Izolacija
Characterization of One Component Foam - Part 5: Insulation
Charakterisierung von Einkomponentenschäumen - Teil 5: Dämmung
Caractérisation des mousses monocomposants - Partie 5 : Isolation
Ta slovenski standard je istoveten z: EN 17333-5:2020
ICS:
83.180 Lepila Adhesives
SIST EN 17333-5:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 17333-5:2020
---------------------- Page: 2 ----------------------
SIST EN 17333-5:2020
EN 17333-5
EUROPEAN STANDARD
NORME EUROPÉENNE
March 2020
EUROPÄISCHE NORM
ICS 83.180
English Version
Characterisation of one component foam - Part 5:
Insulation
Caractérisation des mousses monocomposants - Partie Charakterisierung von Einkomponentenschäumen -
5 : Isolation Teil 5: Dämmung
This European Standard was approved by CEN on 1 December 2019.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 17333-5:2020 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 17333-5:2020
EN 17333-5:2020 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Test method . 5
4.1 Principle . 5
4.2 Equipment . 5
4.3 Sampling . 5
4.3.1 Conditioning . 5
4.3.2 Standard test pieces preparation . 5
4.3.3 Special test pieces preparation for dimensions above 30 mm thickness . 6
4.4 Test procedure . 7
4.5 Expression of results . 7
4.6 Test report . 8
Bibliography . 9
2
---------------------- Page: 4 ----------------------
SIST EN 17333-5:2020
EN 17333-5:2020 (E)
European foreword
This document (EN 17333-5:2020) has been prepared by Technical Committee CEN/TC 193
“Adhesives”, the secretariat of which is held by UNE.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2020, and conflicting national standards
shall be withdrawn at the latest by September 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document is one of the product European Standards within the framework series of EN 17333 on
Characterisation of one component foam, as follows:
— Part 1: Foam yield characteristics;
— Part 2: Expansion characteristics;
— Part 3: Application;
— Part 4: Mechanical strength;
— Part 5: Insulation (this document).
This document is one of a series of standards that specify test methods for determining the properties
of one component foams (OCFs).
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
3
---------------------- Page: 5 ----------------------
SIST EN 17333-5:2020
EN 17333-5:2020 (E)
1 Scope
This document specifies test methods for the evaluation of the insulation properties for moisture
curing, self-curing activatable or water drying foams dispensed from single pressurised foam
containers.
This document does not purport to address all of the safety concerns, if any, associated with its use. It is
the resp
...
SLOVENSKI STANDARD
oSIST prEN 17333-5:2019
01-januar-2019
Karakterizacija enokomponentnih pen (OCF) - 5. del: Izolacija
Characterization of One Component Foam (OCF) - Part 5: Insulation
Charakterisierung von Einkomponentenschäumen - Teil 5: Dämmung
Caractérisation des mousses monocomposants - Partie 5 : Isolation
Ta slovenski standard je istoveten z: prEN 17333-5
ICS:
83.180 Lepila Adhesives
oSIST prEN 17333-5:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 17333-5:2019
---------------------- Page: 2 ----------------------
oSIST prEN 17333-5:2019
DRAFT
EUROPEAN STANDARD
prEN 17333-5
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2018
ICS 83.180
English Version
Characterization of One Component Foam (OCF) - Part 5:
Insulation
Charakterisierung von Einkomponentenschäumen
(OCF) - Teil 5: Dämmung
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 193.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 17333-5:2018 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 17333-5:2019
prEN 17333-5:2018 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Test method . 4
4.1 Principle . 4
4.2 Equipment . 5
4.3 Sampling . 5
4.3.1 Conditioning . 5
4.3.2 Test pieces preparation . 5
4.4 Test procedure . 6
4.5 Expression of results . 7
4.6 Test report . 7
Bibliography . 8
2
---------------------- Page: 4 ----------------------
oSIST prEN 17333-5:2019
prEN 17333-5:2018 (E)
European foreword
This document (prEN 17333-5:2018) has been prepared by Technical Committee CEN/TC 193
“Adhesives”, the secretariat of which is held by UNE.
This document is currently submitted to the CEN Enquiry.
This document is one of the product European Standards within the framework series of EN 17333 on
Characterization of One Component Foam (OCF), as follows:
— Part 1: Yield
— Part 2: Expansion
— Part 3: Application
— Part 4: Mechanical Strength
— Part 5: Insulation (this document)
This document is one of a series of standards which specify test methods for determining the properties
of one component fo
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.