SIST EN 62841-3-10:2016
(Main)Electric Motor-Operated Hand-Held Tools, Transportable Tools and Lawn and Garden Machinery - Safety - Part 3-10: Particular requirements for transportable cut-off machines
Electric Motor-Operated Hand-Held Tools, Transportable Tools and Lawn and Garden Machinery - Safety - Part 3-10: Particular requirements for transportable cut-off machines
Standard applies to transportable cut-off machines intended to cut materials such as metals, concrete and masonry and to be fitted with one abrasive - bonded reinforced wheel of Type 41, or - diamond cut-off wheel with the peripheral gaps, if any, not exceeding 10 mm and with - a rated no-load speed not exceeding a peripheral speed of the wheel of 100 m/s with the maximum wheel diameter and - a wheel diameter range of 250 mm to 410 mm. This standard does not apply to: - transportable mitre saws; - transportable tile saws; - transportable metal saws.
Elektrische motorbetriebene handgeführte Werkzeuge, transportable Werkzeuge und Rasen- und Gartenmaschinen - Sicherheit - Teil 3-10: Besondere Anforderungen für transportable Trennschleifmaschinen
Outils électroportatifs à moteur, outils portables et machines pour jardins et pelouses - Sécurité - Partie 3-10: Exigences particulières pour les tronçonneuses à disque transportables
IEC 62841-3-10:2015 s’applique aux tronçonneuses à disque transportables destinées au découpage de matériaux tels que les métaux, le béton et la maçonnerie, munies d’un disque abrasif du type disque aggloméré renforcé de Type 41, ou disque à tronçonner diamant à rainures périphériques, le cas échéant, ne dépassant pas 10 mm et avec une vitesse assignée à vide ne dépassant pas une vitesse périphérique du disque de 100 m/s avec le diamètre de disque maximal et une plage de diamètres de disque compris entre 250 mm et 410 mm.
La présente norme ne s’applique pas aux: scies à onglets transportables, scies à céramique transportables ou aux scies à métaux transportables.
L’attention des Comités Nationaux est attirée sur le fait que les fabricants d’appareils et les organismes d’essai peuvent avoir besoin d’une période transitoire après la parution d’une nouvelle publication IEC, ou d’une publication amendée ou révisée, pour fabriquer des produits conformes aux nouvelles exigences et pour adapter leurs équipements aux nouveaux essais ou aux essais révisés. Le comité recommande que le contenu de cette publication soit entériné au niveau national au plus tôt 36 mois après la date de publication.
La présente Partie 3-10 doit être utilisée conjointement avec la première édition de l’IEC 62841-1:2014.
Mots clés: outils portables, outils transportables, tronçonneuses à disque transportables
Le contenu du corrigendum de juillet 2016 a été intégré dans ce texte.
Elektromotorna ročna orodja, prenosna orodja ter stroji za trato in vrt - Varnost - 3-10. del: Posebne zahteve za premične rezalnike
Standard se uporablja za prenosne rezalnike za rezanje materialov, kot so kovine, beton in zidovje, na katere se namesti – ojačana abrazivna plošča tipa 41 ali – diamantna rezalna plošča z morebitnimi perifernimi luknjami, ki niso večje do 10 mm, – z nazivno hitrostjo brez obremenitve, ki ne presega periferne hitrosti plošče 100 m/s pri največjem premeru plošče in – razponom premera plošče od 250 mm do 410 mm. Ta standard se ne uporablja za: – prenosne zajeralne žage; – prenosne žage za ploščice; – prenosne žage za kovino.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 62841-3-10:2016
01-marec-2016
1DGRPHãþD
SIST EN 61029-2-10:2010
SIST EN 61029-2-10:2010/A11:2014
(OHNWURPRWRUQDURþQDRURGMDSUHQRVQDRURGMDWHUVWURML]DWUDWRLQYUW9DUQRVW
GHO 3RVHEQH]DKWHYH]DSUHPLþQHUH]DOQLNH
Electric Motor-Operated Hand-Held Tools, Transportable Tools and Lawn and Garden
Machinery - Safety - Part 3-10: Particular requirements for transportable cut-off machines
Ta slovenski standard je istoveten z: EN 62841-3-10:2015
ICS:
25.100.01 Rezalna orodja na splošno Cutting tools in general
25.140.20 (OHNWULþQDRURGMD Electric tools
SIST EN 62841-3-10:2016 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 62841-3-10:2016
---------------------- Page: 2 ----------------------
SIST EN 62841-3-10:2016
EUROPEAN STANDARD EN 62841-3-10
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2015
ICS 25.140.20 Supersedes EN 61029-2-10:2010
English Version
Electric motor-operated hand-held tools, transportable tools and
lawn and garden machinery - Safety - Part 3-10: Particular
requirements for transportable cut-off machines
(IEC 62841-3-10:2015 , modified)
Outils électroportatifs à moteur, outils portables et machines Elektrische motorbetriebene handgeführte Werkzeuge,
pour jardins et pelouses - Sécurité - Partie 3-10: Exigences transportable Werkzeuge und Rasen- und
particulières pour les scies à onglets transportables Gartenmaschinen - Sicherheit - Teil 3-10: Besondere
(IEC 62841-3-10:2015 , modifiée) Anforderungen für transportable Trennschleifmaschinen
(IEC 62841-3-10:2015 , modifiziert)
This European Standard was approved by CENELEC on 2015-10-19. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 62841-3-10:2015 E
---------------------- Page: 3 ----------------------
SIST EN 62841-3-10:2016
EN 62841-3-10:2015 (E)
European foreword
The text of document 116/240/FDIS, future edition 1 of IEC 62841-3-10, prepared by IEC/TC 116 “Safety
of motor-operated electric tools” was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN 62841-3-10:2015.
A draft amendment, which covers common modifications to IEC 62841-3-10:2015, was prepared by
CLC/TC 116 “Safety of motor-operated electric tools” and approved by CENELEC.
The following dates are fixed:
– latest date by which this document has to be implemented (dop) 2016-10-19
at national level by publication of an identical
national standard or by endorsement
– latest date by which the national standards conflicting (dow) 2019-10-19
with this document have to be withdrawn
EN 62841-3-10:2015 supersedes EN 61029-2-10:2010 + A11:2013.
This European Standard is divided into four parts:
Part 1: General requirements which are common to most electric motor operated tools (for the
purpose of this standard referred to simply as tools) which could come within the scope of
this standard;
Part 2, 3 or 4: Requirements for particular types of tools which either supplement or modify the
requirements given in Part 1 to account for the particular hazards and characteristics of
these specific tools.
This Part 3-10 is to be used in conjunction with EN 62841-1:2015.
This Part 3-10 supplements or modifies the corresponding clauses in EN 62841-1:2015, so as to convert
it into the European Standard: Particular requirements for transportable cut-off machines.
Where a particular subclause of Part 1 is not mentioned in this Part 3-10, that subclause applies as far as
relevant. When this standard states "addition", "modification" or "replacement", the relevant text in Part 1
is to be adapted accordingly.
Compliance with the clauses of Part 1 together with this Part 3-10 provides one means of conforming with
the essential health and safety requirements of the Directive concerned.
Warning: Other requirements and other EU Directives can be applicable to the products falling within
the scope of this standard.
This European Standard follows the overall requirements of EN ISO 12100.
The following print types are used:
- requirements; in roman type
- test specifications: in italic type;
- notes: in smaller roman type.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent
rights.
This document has been prepared under a mandate given to CENELEC by the European Commission
and the European Free Trade Association and supports essential requirements of EU Directive(s).
For the relationship with EU Directive(s), see informative Annex ZZ, which is an integral part of this
document.
2
---------------------- Page: 4 ----------------------
SIST EN 62841-3-10:2016
EN 62841-3-10:2015 (E)
Endorsement notice
The text of the International Standard IEC 62841-3-10:2015 was approved by CENELEC as a
European Standard with agreed common modifications.
COMMON MODIFICATIONS
Replace the title of Annex I by the following:
Annex I
(normative)
Measurement of noise and vibration emissions
Add the following annexes:
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1 When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu
This annex from EN 62841-1:2015 is applicable with the following addition:
Publication Year Title EN/HD Year
ISO 603-15 - - -
Bonded abrasive products - Dimensions -
Part 15: Grinding wheels for cutting-off on
stationary or mobile cutting-off machines
ISO 630 Series Structural steels - -
3
---------------------- Page: 5 ----------------------
SIST EN 62841-3-10:2016
EN 62841-3-10:2015 (E)
Annex ZZ
(informative)
Coverage of Essential Requirements of Directive 2006/42/EC
This European Standard has been prepared under a mandate given to CENELEC by the European
Commission and the European Free Trade Association and within its scope the standard covers all
relevant Essential Requirements as given in EU Directive 2006/42/EC (Machinery Directive).
Compliance with this standard provides one means of conformity with the specified essential
requirements of the Directives concerned.
WARNING: Other requirements and other EU Directives may be applicable to the products falling within
the scope of this standard.
4
---------------------- Page: 6 ----------------------
SIST EN 62841-3-10:2016
IEC 62841-3-10
®
Edition 1.0 2015-09
INTERNATIONAL
STANDARD
colour
inside
Electric motor-operated hand-held tools, transportable tools and lawn and
garden machinery – Safety –
Part 3-10: Particular requirements for transportable cut-off machines
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 25.140.20 ISBN 978-2-8322-2912-5
Warning! Make sure that you obtained this publication from an authorized distributor.
® Registered trademark of the International Electrotechnical Commission
---------------------- Page: 7 ----------------------
SIST EN 62841-3-10:2016
– 2 – IEC 62841-3-10:2015 © IEC 2015
CONTENTS
FOREWORD . 4
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 General requirements . 7
5 General conditions for the tests . 7
6 Radiation, toxicity and similar hazards . 8
7 Classification . 8
8 Marking and instructions . 8
9 Protection against access to live parts . 11
10 Starting . 11
11 Input and current . 11
12 Heating . 11
13 Resistance to heat and fire . 11
14 Moisture resistance . 11
15 Resistance to rusting . 11
16 Overload protection of transformers and associated circuits . 11
17 Endurance . 11
18 Abnormal operation . 12
19 Mechanical hazards . 12
20 Mechanical strength . 17
21 Construction . 18
22 Internal wiring . 18
23 Components . 19
24 Supply connection and external flexible cords . 19
25 Terminals for external conductors . 19
26 Provision for earthing . 19
27 Screws and connections . 19
28 Creepage distances, clearances and distances through insulation . 19
Annexes . 26
Annex I (informative) Measurement of noise and vibration emissions . 26
Annex K (normative) Battery tools and battery packs . 27
Bibliography . 28
Figure 101 – Example of a cut-off machine . 20
Figure 102 – Examples of gaps and rake angles . 21
Figure 103 – Wheel guards . 22
Figure 104 – Test probe . 22
Figure 105 – Spark deflection . 23
Figure 106 – Principal designs and dimensions of flanges . 24
Figure 107 – Position of test hole for impact test . 25
---------------------- Page: 8 ----------------------
SIST EN 62841-3-10:2016
IEC 62841-3-10:2015 © IEC 2015 – 3 –
Figure 108 – Wheel guard material strength test . 25
Table 4 – Required performance levels . 12
Table 101 – Flange dimensions . 16
Table 102 – Torques for testing flanges . 17
Table I.101 – Noise test conditions for cut-off machines . 26
---------------------- Page: 9 ----------------------
SIST EN 62841-3-10:2016
– 4 – IEC 62841-3-10:2015 © IEC 2015
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
ELECTRIC MOTOR-OPERATED HAND-HELD TOOLS,
TRANSPORTABLE TOOLS AND LAWN AND GARDEN MACHINERY –
SAFETY –
Part 3-10: Particular requirements for transportable cut-off machines
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 62841-3-10 has been prepared by IEC technical committee 116:
Safety of motor-operated electric tools.
The text of this standard is based on the following documents:
FDIS Report on voting
116/240/FDIS 116/253/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
---------------------- Page: 10 ----------------------
SIST EN 62841-3-10:2016
IEC 62841-3-10:2015 © IEC 2015 – 5 –
This Part 3-10 is to be used in conjunction with the first edition of IEC 62841-1 (2014).
This Part 3-10 supplements or modifies the corresponding clauses in IEC 62841-1, so as to
convert it into the IEC Standard: Particular requirements for transportable cut-off machines.
Where a particular subclause of Part 1 is not mentioned in this Part 3-10, that subclause
applies as far as relevant. Where this standard states “addition”, “modification” or
“replacement”, the relevant text in Part 1 is to be adapted accordingly.
The following print types are used:
– requirements: in roman type;
– test specifications: in italic type;
– notes: in small roman type.
Words in bold in the text are defined in Clause 3. When a definition concerns an adjective,
the adjective and the associated noun are also in bold.
Subclauses, notes and figures which are additional to those in Part 1 are numbered starting
from 101.
A list of all parts of the IEC 62841 series, under the general title: Electric motor-operated
hand-held tools, transportable tools and lawn and garden machinery – Safety, can be found
on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC website under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
A bilingual version of this publication may be issued at a later date.
NOTE The attention of National Committees is drawn to the fact that equipment manufacturers and testing
organizations may need a transitional period following publication of a new, amended or revised IEC publication in
which to make products in accordance with the new requirements and to equip themselves for conducting new or
revised tests.
It is the recommendation of the committee that the content of this publication be adopted for implementation
nationally not earlier than 36 months from the date of publication.
IMPORTANT – The 'colour inside' logo on the cover page of this publication indicates
that it contains colours which are considered to be useful for the correct
understanding of its contents. Users should therefore print this document using a
colour printer.
---------------------- Page: 11 ----------------------
SIST EN 62841-3-10:2016
– 6 – IEC 62841-3-10:2015 © IEC 2015
ELECTRIC MOTOR-OPERATED HAND-HELD TOOLS,
TRANSPORTABLE TOOLS AND LAWN AND GARDEN MACHINERY –
SAFETY –
Part 3-10: Particular requirements for transportable cut-off machines
1 Scope
This clause of Part 1 is applicable, except as follows:
Addition:
This part of IEC 62841 applies to transportable cut-off machines intended to cut materials
such as metals, concrete and masonry and to be fitted with one abrasive
– bonded reinforced wheel of Type 41, or
– diamond cut-off wheel with the peripheral gaps, if any, not exceeding 10 mm
and with
– a rated no-load speed not exceeding a peripheral speed of the wheel of 100 m/s with the
maximum wheel diameter and
– a wheel diameter range of 250 mm to 410 mm.
This standard does not apply to:
– transportable mitre saws;
– transportable tile saws;
– transportable metal saws.
NOTE 101 Transportable mitre saws are covered by IEC 62841-3-9. Transportable tile saws will be covered by a
future part of IEC 62841-3. Transportable metal saws will be covered by a future part of IEC 62841-3.
2 Normative references
This clause of Part 1 is applicable except as follows:
Addition:
ISO 603-15, Bonded abrasive products – Dimensions – Part 15: Grinding wheels for cutting-
off on stationary or mobile cutting-off machines
ISO 630 (all parts), Structural steels
3 Terms and definitions
This clause of Part 1 is applicable, except as follows:
3.101
inner flange
part that contacts and provides support to the back side of the wheel and is located on the
spindle between wheel and tool
---------------------- Page: 12 ----------------------
SIST EN 62841-3-10:2016
IEC 62841-3-10:2015 © IEC 2015 – 7 –
3.102
bonded reinforced wheel
wheel for different applications and of a type in accordance with ISO 603-15
3.103
cut-off machine
tool designed to cut by means of a rotating abrasive cut-off wheel (bonded reinforced or
diamond), where the wheel is fixed on a spindle which is mounted on a cutting unit, the
machine is equipped with a table which supports and positions the workpiece fixed in a vice
and the cutting unit is fitted to an arm which projects over the table from a pivot located at
the table or on part of the frame of the machine
Note 1 to entry: See Figure 101.
3.104
cutting unit
device with an affixed cut-off wheel, capable of generating a cutting action
3.105
D
maximum specified diameter of the wheel
3.106
diamond wheel
wheel made of metal with a continuous or segmented abrasive rim
3.107
fence
device to position the workpiece and absorb the horizontal forces from the wheel during the
cutting process
3.108
outer flange
part that supports the front side of the wheel and secures and clamps the wheel to the spindle
and the inner flange
3.109
rest position
uppermost position of the cutting unit intended by design
3.110
wheel guard
guard which partly encloses the wheel and gives protection to the operator
4 General requirements
This clause of Part 1 is applicable.
5 General conditions for the tests
This clause of Part 1 is applicable, except as follows:
5.17 Addition:
The mass of the tool shall include the wheel guard and the fence.
---------------------- Page: 13 ----------------------
SIST EN 62841-3-10:2016
– 8 – IEC 62841-3-10:2015 © IEC 2015
Further parts such as carrying means that are required in accordance with the user
instructions shall be included in the mass.
6 Radiation, toxicity and similar hazards
This clause of Part 1 is applicable.
7 Classification
This clause of Part 1 is applicable.
8 Marking and instructions
This clause of Part 1 is applicable, except as follows:
8.1 Addition:
Tools shall also be marked with:
– the rated no-load speed of the output spindle.
8.2 Addition:
Tools shall also be marked with the following safety warning:
“ WARNING – Always wear eye protection” or the sign M004 of ISO 7010 or the following
safety sign:
The eye protection symbol may be modified by adding other personal protective equipment
such as ear protection, dust mask, etc.
8.3 Addition:
Tools shall also be marked with additional information as follows:
– the wheel diameter D;
– the direction of rotation of the wheel indicated on the tool by an arrow raised or sunk or by
any other means no less visible and indelible.
8.14.1 Addition:
The additional safety instructions as specified in 8.14.1.101 shall be given. This part may be
printed separately from the “General Power Tool Safety Warnings”.
For all warnings in 8.14.1.101, the term “cutting unit” may be replaced by another
appropriate term at the discretion of the manufacturer.
---------------------- Page: 14 ----------------------
SIST EN 62841-3-10:2016
IEC 62841-3-10:2015 © IEC 2015 – 9 –
8.14.1.101 Safety instructions for cut-off machines
1) Cut-off machine safety warnings
a) Position yourself and bystanders away from the plane of the rotating wheel. The
guard helps to protect the operator from broken wheel fragments and accidental
contact with wheel.
b) Use only bonded reinforced or diamond cut-off wheels for your power tool. Just
because an accessory can be attached to your power tool, it does not assure safe
operation.
NOTE 1 The wording “bonded reinforced” or “diamond” is used as applicable depending on the
designation of the tool.
c) The rated speed of the accessory must be at least equal to the maximum speed
marked on the power tool. Accessories running faster than their rated speed can
break and fly apart.
d) Wheels must be used only for recommended applications. For example: do not
grind with the side of a cut-off wheel. Abrasive cut-off wheels are intended for
peripheral grinding, side forces applied to these wheels may cause them to shatter.
e) Always use undamaged wheel flanges that are of correct diameter for your
selected wheel. Proper wheel flanges support the wheel thus reducing the possibility
of wheel breakage.
f) The outside diameter and the thickness of your accessory must be within the
capacity rating of your power tool. Incorrectly sized accessories cannot be
adequately guarded or controlled.
g) The arbour size of wheels and flanges must properly fit the spindle of the power
tool. Wheels and flanges with arbour holes that do not match the mounting hardware
of the power tool will run out of balance, vibrate excessively and may cause loss of
control.
h) Do not use damaged wheels. Before each use, inspect the wheels for chips and
cracks. If the power tool or wheel is dropped, inspect for damage or install an
undamaged wheel. After inspecting and installing the wheel, position yourself
and bystanders away from the plane of the rotating wheel and run the power tool
at maximum no load speed for one minute. Damaged wheels will normally break
apart during this test time.
i) Wear personal protective equipment. Depending on application, use face shield,
safety goggles or safety glasses. As appropriate, wear dust mask, hearing
protectors, gloves and shop apron capable of stopping small abrasive or
workpiece fragments. The eye protection must be capable of stopping flying debris
generated by various operations. The dust mask or respirator must be capable of
filtrating particles generated by your operation. Prolonged exposure to high intensity
noise may cause hearing loss.
j) Keep bystanders a safe distance away from work area. Anyone entering the work
area must wear personal protective equipment. Fragments of workpiece or of a
broken wheel may fly away and cause injury beyond immediate area of operation.
k) Position the cord clear of the spinning accessory. If you lose control, the cord may
be cut or snagged and your hand or arm may be pulled into the spinning wheel.
l) Regularly clean the power tool’s air vents. The motor’s fan can draw the dust inside
the housing and excessive accumulation of powdered metal may cause electrical
hazards.
m) Do not operate the power tool near flammable materials. Do not operate the
power tool while placed on a combustible surface such as wood. Sparks could
ignite these materials.
n) Do not use accessories that require liquid coolants. Using water or other liquid
coolants may result in electrocution or shoc
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.