SIST EN 12697-19:2004
(Main)Bituminous mixtures - Test methods for hot mix asphalt - Part 19: Permeability of specimen
Bituminous mixtures - Test methods for hot mix asphalt - Part 19: Permeability of specimen
This European Standard describes a method for determining the vertical and horizontal permeability of cylindrical specimens of bituminous mixtures. The standard applies to specimens cored out of the road, specimens from laboratory made slabs or laboratory specimens pre-pared with a compaction device provided the thickness of the specimen is not less than 2,5 times the nominal maximum particle size of the aggregate in the mixture. The nominal diameter of specimens should be either 100 mm or 150 mm unless the nominal maximum particle size of the aggregate size exceeds 22 mm, when the nominal diameter shall be 150 mm diameter.
Asphalt - Prüfverfahren für Heißasphalt - Teil 19: Durchlässigkeit von Probekörpern
Dieses Dokument legt ein Verfahren zur Bestimmung der vertikalen und horizontalen Durchlässigkeit von zylindrischen Asphalt-Probekörpern fest. Diese Norm gilt für durch Kernbohren aus einer Fahrbahnbefestigung entnommene Probekörper, für Probekörper aus im Laboratorium hergestellten Platten oder für im Laboratorium mit einer Verdichtungsvorrichtung hergestellte Probekörper, sofern die Dicke des Probekörpers nicht geringer als das 2,5fache der maximalen Nennkorngröße der im Gemisch verwendeten Gesteinskörnung ist. Der Nenndurchmesser der Probekörper sollte entweder 100 mm oder 150 mm betragen, es sei denn, die maximale Nennkorngröße der Gesteinskörnung überschreitet 22 mm; in diesem Falle muss der Nenndurchmesser 150 mm betragen.
Mélanges bitumineux - Méthodes d'essai pour mélange hydrocarboné a chaud - Partie 19: Perméabilité des éprouvettes
Le présent document décrit une méthode pour déterminer la perméabilité horizontale et verticale d'éprouvettes cylindriques de mélanges bitumineux. Cette norme s'applique a des carottes prélevées dans la chaussée, des éprouvettes extraites de plaques fabriquées en laboratoire avec une table de compactage telle que l'épaisseur de l'éprouvette ne soit pas moins de 2,5 fois la dimension nominale maximale des granulats du mélange. Il convient que le diametre nominal des éprouvettes soit de 100 mm ou de 150 mm, si la dimension maximale des granulats dépasse 22 mm, le diametre nominal doit etre de 150 mm.
Bitumenske zmesi – Preskusne metode za vroče asfaltne zmesi – 19. del: Prepustnost preskušancev
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Bituminous mixtures - Test methods for hot mix asphalt - Part 19: Permeability of specimenMélanges bitumineux - Méthodes d'essai pour mélange hydrocarboné a chaud - Partie 19: Perméabilité des éprouvettesAsphalt - Prüfverfahren für Heißasphalt - Teil 19: Durchlässigkeit von ProbekörpernTa slovenski standard je istoveten z:EN 12697-19:2004SIST EN 12697-19:2004en93.080.20Materiali za gradnjo cestRoad construction materialsICS:SLOVENSKI
STANDARDSIST EN 12697-19:200401-september-2004
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 12697-19July 2004ICS 93.080.20English versionBituminous mixtures - Test methods for hot mix asphalt - Part19: Permeability of specimenMélanges bitumineux - Méthodes d'essai pour mélangehydrocarboné à chaud - Partie 19: Perméabilité deséprouvettesAsphalt - Prüfverfahren für Heißasphalt - Teil 19:Durchlässigkeit von ProbekörpernThis European Standard was approved by CEN on 24 March 2004.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2004 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 12697-19:2004: E
EN 12697-19:2004 (E) 2 Contents page Foreword.3 1 Scope.6 2 Normative references.6 3 Principle.6 4 Vertical permeability.6 4.1 General.6 4.2 Apparatus for vertical permeability.6 4.3 Procedure.6 4.4 Calculation.8 5 Horizontal permeability.8 5.1 General.8 5.2 Apparatus for horizontal permeability.8 5.3 Procedure.9 5.4 Calculation.10 6 Test report.11 6.1 General.11 6.2 Information on specimen.11 6.3 Information on the test and results.11 7 Precision.11
EN 12697-19:2004 (E) 3 Foreword This document (EN 12697-19:2004) has been prepared by Technical Committee CEN/TC 227 “Road materials”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2005, and conflicting national standards shall be withdrawn at the latest by January 2005. This document is one of a series of standards as listed below: EN 12697-1, Bituminous mixtures — Test methods for hot mix asphalt — Part 1: Soluble binder content. EN 12697-2, Bituminous mixtures — Test methods for hot mix asphalt — Part 2: Determination of particle size distribution. EN 12697-3, Bituminous mixtures — Test methods for hot mix asphalt — Part 3: Bitumen recovery: Rotary evaporator. EN 12697-4, Bituminous mixtures — Test methods for hot mix asphalt — Part 4: Bitumen recovery: Fractionating column. EN 12697-5, Bituminous mixtures — Test methods for hot mix asphalt — Part 5: Determination of the maximum density. EN 12697-6, Bituminous mixtures — Test methods for hot mix asphalt — Part 6: Determination of bulk density of bituminous specimens. EN 12697-7, Bituminous mixtures — Test methods for hot mix asphalt — Part 7: Determination of bulk density of bituminous specimens by gamma rays. EN 12697-8, Bituminous mixtures — Test methods for hot mix asphalt — Part 8: Determination of void characteristics of bituminous specimens. EN 12697-9, Bituminous mixtures — Test methods for hot mix asphalt — Part 9: Determination of the reference density. EN 12697-10, Bituminous mixtures — Test methods for hot mix asphalt — Part 10: Compactability. EN 12697-11, Bituminous mixtures — Test methods for hot mix asphalt — Part 11: Determination of the affinity between aggregate and bitumen. EN 12697-12, Bituminous mixtures — Test methods for hot mix asphalt — Part 12: Determination of the water sensitivity of bituminous specimens. EN 12697-13, Bituminous mixtures — Test methods for hot mix asphalt — Part 13: Temperature measurement. EN 12697-14, Bituminous mixtures — Test methods for hot mix asphalt — Part 14: Water content. EN 12697-15, Bituminous mixtures — Test methods for hot mix asphalt — Part 15: Determination of the segregation sensitivity. EN 12697-16, Bituminous mixtures — Test methods for hot mix asphalt — Part 16: Abrasion by studded tyres.
EN 12697-19:2004 (E) 4 EN 12697-17, Bituminous mixtures — Test methods for hot mix asphalt — Part 17: Particle loss of porous asphalt specimen. EN 12697-18, Bituminous mixtures — Test methods for hot mix asphalt — Part 18: Binder drainage. EN 12697-19, Bituminous mixtures — Test methods for hot mix asphalt — Part 19: Permeability of specimen. EN 12697-20, Bituminous mixtures — Test methods for hot mix asphalt — Part 20: Indentation using cube or Marshall specimens. EN 12697-21, Bituminous mixtures — Test methods for hot mix asphalt — Part 21: Indentation using plate specimens. EN 12697-22, Bituminous mixtures — Test methods for hot mix asphalt — Part 22: Wheel tracking. EN 12697-23, Bituminous mixtures — Test methods for hot mix asphalt — Part 23: Determination of the indirect tensile strength of bituminous specimens. EN 12697-24, Bituminous mixtures — Test methods for hot mix asphalt — Part 24: Resistance to fatigue. prEN 12697-25, Bituminous mixtures — Test methods for hot mix asphalt — Part 25: Cyclic compression test. EN 12697-26, Bituminous mixtures — Test methods for hot mix asphalt — Part 26: Stiffness. EN 12697-27, Bituminous mixtures — Test methods for hot mix asphalt — Part 27: Sampling. EN 12697-28, Bituminous mixtures — Test methods for hot mix asphalt — Part 28: Preparation of samples for determining binder content, water content and grading. EN 12697-29, Bituminous mixtures — Test method for hot mix asphalt — Part 29: Determination of the dimensions of a bituminous specimen. EN 12697-30, Bituminous mixtures — Test methods for hot mix asphalt — Part 30: Specimen preparation, impact compactor. EN 12697-31, Bituminous mixtures — Test methods for hot mix asphalt — Part 31: Specimen preparation by gyratory compactor. EN 12697-32, Bituminous mixtures — Test methods for hot mix asphalt — Part 32: Laboratory compaction of bituminous mixtures by vibratory compactor. EN 12697-33, Bituminous mixtures — Test methods for hot mix asphalt —
Part 33: Specimen prepared by roller compactor. EN 12697-34, Bituminous mixtures — Test methods for hot mix asphalt — Part 34: Marshall test. prEN 12697-35, Bituminous mixtures — Test methods for hot mix asphalt — Part 35: Laboratory mixing. EN 12697-36, Bituminous mixtures — Test methods for hot mix asphalt — Part 36: Determination of the thickness of a bituminous pavement. EN 12697-37, Bituminous mixtures — Test methods for hot mix asphalt — Part 37: Hot sand test for the adhesivity of binder on precoated chippings for HRA. EN 12697-38, Bituminous mixtures — Test methods for hot mix asphalt — Part 38: Common equipment and calibration.
EN 12697-19:2004 (E) 5 prEN 12697-39, Bituminous mixtures — Test methods for hot mix asphalt — Part 39: Binder content by ignition. prEN 12697-40, Bituminous mixtures — Test methods for hot mix asphalt — Part 40: In-situ drainability. prEN 12697-41, Bituminous mixtures — Test methods for hot mix asphalt — Part 41: Resistance to de-icing fluids. prEN 12697-42, Bituminous mixtures — Test methods for hot mix asphalt — Part 42: Amount of foreign matters in reclaimed asphalt. prEN 12697-43, Bituminous mixtures — Test methods for hot mix asphalt — Part 43: Resistance to fuel. No existing European Standard is superseded. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to impleme
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.