EN 12697-19:2004

Bituminous mixtures - Test methods for hot mix asphalt - Part 19: Permeability of specimen

This European Standard describes a method for determining the vertical and horizontal permeability of cylindrical specimens of bituminous mixtures. The standard applies to specimens cored out of the road, specimens from laboratory made slabs or laboratory specimens pre-pared with a compaction device provided the thickness of the specimen is not less than 2,5 times the nominal maximum particle size of the aggregate in the mixture. The nominal diameter of specimens should be either 100 mm or 150 mm unless the nominal maximum particle size of the aggregate size exceeds 22 mm, when the nominal diameter shall be 150 mm diameter.

Asphalt - Prüfverfahren für Heißasphalt - Teil 19: Durchlässigkeit von Probekörpern

Dieses Dokument legt ein Verfahren zur Bestimmung der vertikalen und horizontalen Durchlässigkeit von zylindrischen Asphalt-Probekörpern fest. Diese Norm gilt für durch Kernbohren aus einer Fahrbahnbefestigung entnommene Probekörper, für Probekörper aus im Laboratorium hergestellten Platten oder für im Laboratorium mit einer Verdichtungsvorrichtung hergestellte Probekörper, sofern die Dicke des Probekörpers nicht geringer als das 2,5fache der maximalen Nennkorngröße der im Gemisch verwendeten Gesteinskörnung ist. Der Nenndurchmesser der Probekörper sollte entweder 100 mm oder 150 mm betragen, es sei denn, die maximale Nennkorngröße der Gesteinskörnung überschreitet 22 mm; in diesem Falle muss der Nenndurchmesser 150 mm betragen.

Mélanges bitumineux - Méthodes d'essai pour mélange hydrocarboné à chaud - Partie 19: Perméabilité des éprouvettes

Le présent document décrit une méthode pour déterminer la perméabilité horizontale et verticale d'éprouvettes cylindriques de mélanges bitumineux. Cette norme s'applique à des carottes prélevées dans la chaussée, des éprouvettes extraites de plaques fabriquées en laboratoire avec une table de compactage telle que l'épaisseur de l'éprouvette ne soit pas moins de 2,5 fois la dimension nominale maximale des granulats du mélange. Il convient que le diamètre nominal des éprouvettes soit de 100 mm ou de 150 mm, si la dimension maximale des granulats dépasse 22 mm, le diamètre nominal doit être de 150 mm.

Bitumenske zmesi – Preskusne metode za vroče asfaltne zmesi – 19. del: Prepustnost preskušancev

General Information

• Status: Withdrawn
• Publication Date: 06-Jul-2004
• Withdrawal Date: 03-Jul-2007
• ICS: 93.080.20 - Road construction materials
• Technical Committee: CEN/TC 227 - Road materials
• Drafting Committee: CEN/TC 227/WG 1 - Bituminous mixtures
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 04-Jul-2007
• Completion Date: 04-Jul-2007
• Directive: 305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
• Directive: 89/106/EEC - Construction products
• Ref Project: SIST EN 12697-19:2004 - Bituminous mixtures - Test methods for hot mix asphalt - Part 19: Permeability of specimen

Relations

• Merged Into: EN 12697-19:2004+A1:2007 - Bituminous mixtures - Test methods for hot mix asphalt - Part 19: Permeability of specimen
• Effective Date: 18-Jan-2023

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Bituminous mixtures - Test methods for hot mix asphalt - Part 19: Permeability of specimenMélanges bitumineux - Méthodes d'essai pour mélange hydrocarboné a chaud - Partie 19: Perméabilité des éprouvettesAsphalt - Prüfverfahren für Heißasphalt - Teil 19: Durchlässigkeit von ProbekörpernTa slovenski standard je istoveten z:EN 12697-19:2004SIST EN 12697-19:2004en93.080.20Materiali za gradnjo cestRoad construction materialsICS:SLOVENSKI
STANDARDSIST EN 12697-19:200401-september-2004

EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 12697-19July 2004ICS 93.080.20English versionBituminous mixtures - Test methods for hot mix asphalt - Part19: Permeability of specimenMélanges bitumineux - Méthodes d'essai pour mélangehydrocarboné à chaud - Partie 19: Perméabilité deséprouvettesAsphalt - Prüfverfahren für Heißasphalt - Teil 19:Durchlässigkeit von ProbekörpernThis European Standard was approved by CEN on 24 March 2004.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2004 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 12697-19:2004: E

Part 33: Specimen prepared by roller compactor. EN 12697-34, Bituminous mixtures — Test methods for hot mix asphalt — Part 34: Marshall test. prEN 12697-35, Bituminous mixtures — Test methods for hot mix asphalt — Part 35: Laboratory mixing. EN 12697-36, Bituminous mixtures — Test methods for hot mix asphalt — Part 36: Determination of the thickness of a bituminous pavement. EN 12697-37, Bituminous mixtures — Test methods for hot mix asphalt — Part 37: Hot sand test for the adhesivity of binder on precoated chippings for HRA. EN 12697-38, Bituminous mixtures — Test methods for hot mix asphalt — Part 38: Common equipment and calibration.
...