SIST EN 29775:2000
(Main)Small craft - Remote steering systems for single outboard motors of 15 kW to 40 kW power (ISO 9775:1990)
Small craft - Remote steering systems for single outboard motors of 15 kW to 40 kW power (ISO 9775:1990)
This International Standard specifies requirements and test methods for remote push-pull cable steering systems and their major component items, used for small craft with a single outboard motor of 15 kW to 40 kW power. [Modified by ISO/TC decision]
Kleine Wasserfahrzeuge - Steueranlagen für Einzel-Außenbordmotoren mit einer Leistung von 15 kW bis 40 kW (ISO 9775:1990)
Navires de plaisance - Appareils a gouverner commandés a distance pour moteurs hors-bord uniques de puissance comprise entre 15 kW et 40 kW (ISO 9775:1990)
La présente Norme internationale spécifie les caractéristiques exigées et prescrit les méthodes d'essai des appareils à gouverner commandés à distance, à transmission par câbles va-et-vient («push-pull»), et de leurs principaux éléments constitutifs, installés sur des navires de plaisance à un seul moteur hors-bord dont la puissance est comprise entre 15 kW et 40 kW.
Mala plovila - Daljinski sistemi krmiljenja za enojne izvenkrmne motorje z močjo od 15 kW do 40 kW (ISO 9775:1990)
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Kleine Wasserfahrzeuge - Steueranlagen für Einzel-Außenbordmotoren mit einer Leistung von 15 kW bis 40 kW (ISO 9775:1990)Navires de plaisance - Appareils a gouverner commandés a distance pour moteurs hors-bord uniques de puissance comprise entre 15 kW et 40 kW (ISO 9775:1990)Small craft - Remote steering systems for single outboard motors of 15 kW to 40 kW power (ISO 9775:1990)47.080ýROQLSmall craft47.020.70Navigacijska in krmilna opremaNavigation and control equipmentICS:Ta slovenski standard je istoveten z:EN 29775:1993SIST EN 29775:2000en01-april-2000SIST EN 29775:2000SLOVENSKI
STANDARD
SIST EN 29775:2000
SIST EN 29775:2000
SIST EN 29775:2000
SIST EN 29775:2000
SIST EN 29775:2000
INTERNATIONAL STANDARD First edi tion 1990-12-15 Small traft - Remote steering Systems for Single outboard motors of 15 kW to 40 kW power Navires de plaisance - Appareils 6 gouverner commandes ZI distance pour moteurs hors-hord uniques de puissarice comprise entre 15 kW et 40 kW -- ---- ____-__-- -----.------------ P-e--.-____ Reference number ISO 9775: 199O(E) SIST EN 29775:2000
ISO 9775:1990(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national Standards bodies (ISO member bodies). The work of preparing international Standards is normally carried out through ISO technical committees. Esch member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, govern- mental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an Inter- national Standard requires approval by at least 75 % of the member bodies casting a vote. International Standard ISO 9775 was prepared by Technical Committee ISO/TC 188, Small traft. NOTE 1 This International Standard specifies requirements and test methods for remote steering Systems as cited in clause 1. They are thus more speciaiized requirements than those given in a parallel document, ISO 8848, Smaii traft -- Remote steering Systems. 0 ISO 1990 All rights reserved. No part of this publication may be reproduced or utilized in any form or by any means, electronie or mechanical, including photocopying and microfilm, without Permission in writing from the publisher. International Organization for Standardiz ation Case Postale 56 l CH-121 1 Geneve 20 l Switzerland Printed in Switzerland ii SIST EN 29775:2000
_---- __ - INTERNATIONAL STANDARD ISO 9775:1996(E) Small traft - Remote steering Systems for Single outboard motors of 15 kW to 40 kW power 1 Scope This International Standard specifies requirements and test methods for remote push-pull cable steer- ing Systems and their major component items, used for small traft with a Single outboard motor of 15 kW to 40 kW power. 2 Definitions For the purposes of this International Standard, the following definitions apply. 2.1 steering System: Assembly including all com- ponents necessary to transmit remote manual effort to the outboard motor. 2,2 boat-mounted steering System: System in which an output ram guide tube is secured to the boat. 2.3 motor-mounted steering System: System in which an output ram guide tube is secured to the engine. 2.4 drag link: Device in a motor-mounted steering System by which the linear forte of the output ram is transmitted to the motor steering arm. 2.5 helm: Mechanism, exclusive of a steering- wheel or other means for manual application of controlling forte, by which controlling forte is fed into a steering System cable or other force- transmission means. 2.6 minimum retained System Performance: System capability after test(s) such that at least 90 % of the steering arc normally available each side of the mid-Position may be obtained by exertion of no more than 27 Nm of torque at the helm, through the wheel or other normal control. This criterion does not define steering System per- formante while a boat is underway but is intended to provide quantitative limits for design and test purposes. 3 General requirements 3.1 When steering Systems are factory-installed in the boat, the complete System shall be supplied. In outboard motor-boats, the System shall be supplied complete to the interface point at the ram output end as shown in figure 1. SIST EN 29775:2000
ISO 9775:1990(E) Dimensions in miilimetres 430 (at mid-travel Position) 300 min. C 12,7max. Fiat 10,7min. * L Tube0 15,75 + O,i3 Interface Point --/ \ Coupler nut 7/8-14 UNF-2B thread (optional for boat-mounted Systems) NOTE - Minimum travel : 100 mm each side of mid-travel Position; maximum travel : 115 mm each side of mid-travei Position. Figure 1 3.2 The steering System selected shall be inst;llled and complying with the requiremcnts in 3.5.1 to in accordance with this International Standard. 3.5.3. 3.3 lt shall be specified whether the boat is suit- able for motor-mounted steering Systems, boat- mounted steering Systems or both. If the boat is suitable for boat-mounted steering Systems, it shall also be specified whether weil mounting, transom mounting or both (see figure2) may be used. 3.4 All threaded fasteners use of which affects safe Operation of the steering System shall incorporate locking means. 3.5 Threaded fasteners use of which affects safe Operation of the steering System and which are in- tended to be mounted or adjusted when installing the steering System in the boat, and which may be expected to be disturbed by installation or adjust- ment procedures, shall be locked by a locking de- vice provided with instructions for correct assembly Output ram 3.5.1 Loose lack-washers, fasteners with metallic distorting threads and adhesive at-e prohibited. 3.5.2 Plain, threaded jam nuts are prohibited ex- cept that they may be used to permit adjustment and shall be designed so that total Separation of par-ts or other complete loss of steering will not occur should they loosen. NOTE 2 For assemblies not intended to be disassem- bled for installation, the choice of locking means is within the discretion of the System manufacturer. 3.5.3 A locking device shall be so designed that its presence tan be determined by visual inspection or feel by a layman after installation. 3.6 Connection fittings including quick-disconnect fittings relying upon a spring or springs to maintain the connection shall not be used. SIST EN 29775:2000
ISO 9775:1990(E) Dimensions in millimetres Swivel axis to be 102~$ Square off face of transom (motor weil and transom mounting) Ctrritrnl QV;C +n ho 13 mav ab-*,- JVVIVCI OAl3 CU LJG IL IIIUA. 03uve top of motor mounting face (motor well and transom mounting) NOTE - If the swivel is mounted in the motor weil side fitting, the motor weil shall provide for 380 mm mid-travel Position from the swivel axis to the motor axis. < 7/8--14 UNF-ZB th read; mi Jength 16 on cable support hAn+nr mnn ~n+;nn fgpn nf +hn PI--- ~---I--A CI IG Lidl 1 IfJ UldLKt=l Motor mounting 380 mid-travel Position swivel axis to motor axis Motor axis Al LlbUI” LI\ 15O min. W Articulation l5O min. 380 mid-travel Position swivel axis to motor axis a) Motor weil mounting b) Transom mounting NOTE - Minimum travel : 100 mm each side of mid-travel Position; maximum travel : 115 mm each side of mid-travel Position. Figure 2 - Beat-mounted steering System 4 Qutboard motor requirements 4.1 The steering Stops on the outboard motor shall permit at least 30° of angular movement to either Gde. 4.2 Outboard motors shall meet the applicable di- mensional requirements indicated in figure 3 and figure 4. 4.3 The necessary fittings to attach an outboard motor to the steering output ram shown in figure 1 shall be supplied with the outboard motor. 4.4 The outboard motor shall be designed so that, with any combination of motor turn and tilt, there shall be no damaging interference between the mo- tor-, its accessories, and both the boat-mounted sys- tem installed as shown in figure2 and the motor-mounted System, provided the motor is de- signed for both Systems. Appropriate written infor- mation and installation instructions shall be provided, clearly indicating the type of steering System(s) that should be used. 4.5 Outboard motors shall be designed so that the geometry ensures that a static load of 2200 N, ap- plied at the steering-arm connection Point normal to the steering arm in its normal plane of Operation, throughout the maximum steering arc, will not result in steering output ram loadings greater than those specified in 7.2.1. 4.6 The steering arm of the outboard motor shall be provided with a 3/8-24 UNF thread, or a plain hole of 9,65 mm to 9,9 mm diameter at the connection Point. SIST EN 29775:2000
ISO 9775:199O(E) 5 Seering System requirements Dimensions in millimetres Motor axis 5.1 Motor-mounted steering Systems shall meet the dimensional requirements indicated in figure 1, figure 3 and figure 4. 5.2 Boat-mounted steering Systems for outboard motor installations shall meet the dimensional re- yuirements indicated in figure 1 and figure 2. When a joint as shown in figure 2 is replaced by a uni- versal joint with two movement axes, the axis per- pendicular to the transom face shall be located 0 to 13 mm above the motor clamp bracket horizontal mounting face. The second axis shall be 100 mm to 115 mm from the inner surface of the transom and shall be not more than 28,5 mm from the first axis toward the motor. 5.3 Steering cables shall be marked at the engine end with a steering System length which shall be the length from the steering-wheel shaft centre to the hole centre in the steering output ram at the mid- travel Position. The steering cable shall also be marked by the manufacturer that the maximum power permissible is 40 kW. 5.4 Installation instructions for steering helms shall include recommendations for the maximum diameter and deepest wheel dish (see figure 5) that may be used with the helm. In addition, the maxi- mum diameter and deepest wheel dish information shall be permanently marked on the helm assembly to be visible when the helm is installed with the wheel removed. / 718-14 U.NF-2
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.