iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

oSIST prEN ISO 10896-2:2024

(Main)

Rough-terrain trucks - Safety requirements and verification - Part 2: Slewing trucks (ISO/DIS 10896-2:2024)

Rough-terrain trucks - Safety requirements and verification - Part 2: Slewing trucks (ISO/DIS 10896-2:2024)

ISO 10896-2:2016 specifies general safety requirements for slewing rough-terrain variable-reach trucks (hereafter known as "trucks"), consisting of a lower chassis with a slewing upper structure equipped with a telescopic lifting means (pivoted boom), on which a load handling device (e.g., carriage and fork arms) is typically fitted. Fork arms and other integrated attachments are considered to be parts of the truck.
Other standards, in addition to the relevant provisions of this part of ISO 10896, can apply to the attachments.
ISO 10896-2:2016 is not applicable to the following:
a) rough terrain variable-reach trucks covered by ISO 10896‑1 (non-slewing);
b) industrial variable-reach trucks covered by ISO 3691‑2;
c) mobile cranes;
d) machines designed primarily for earth-moving, such as loaders, even if their buckets are replaced by fork arms (see ISO 20474);
e) trucks designed primarily with variable-length load suspension elements (e.g. chain, ropes) from which the load may swing freely in all directions;
NOTE Additional requirements for trucks intended for freely swinging load applications, their lifting devices and attachments, and personnel/work platform applications on trucks, are being developed by ISO/TC 110/SC4.
f) trucks designed primarily for container handling.
The significant hazards covered by this part of ISO 10896 are listed in Annex A. This part of ISO 10896 does not address hazards that can occur
- during manufacture,
- when handling suspended loads, which may swing freely,
- when lifting personnel,
- when using trucks on public roads,
- when operating in potentially explosive atmospheres, or
- with a battery, LPG or hybrid as the primary power source.

Geländegängige Stapler - Sicherheitstechnische Anforderungen und Verifizierung - Teil 2: Schwenkbare Stapler mit veränderlicher Reichweite (ISO/DIS 10896-2:2024)

Chariots tout-terrain - Exigences de sécurité et vérification - Partie 2: Chariots rotatifs (ISO/DIS 10896-2:2024)

Vozila za talni transport - Terenska vozila - Varnostne zahteve in preverjanje- 2. del: Vozila z vrtljivim mehanizmom (ISO/DIS 10896-2:2024)

General Information

Status
Not Published
Public Enquiry End Date
30-Jul-2024
ICS
53.060 - Industrial trucks
Technical Committee
DTN - Lift and transport appliances
Current Stage
4020 - Public enquire (PE) (Adopted Project)
Start Date
23-May-2024
Due Date
10-Oct-2024
Directive
2006/42/EC - Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast)
2023/1230 - Regulation (EU) 2023/1230 of the European Parliament and of the Council of 14 June 2023 on machinery and repealing Directive 2006/42/EC of the European Parliament and of the Council and Council Directive 73/361/EEC (Text with EEA relevance)
Mandate
M/396 - Mandate to CEN and Cenelec for standardisation in the field of machinery
Ref Project
prEN ISO 10896-2 - Rough-terrain trucks - Safety requirements and verification - Part 2: Slewing trucks (ISO/DIS 10896-2:2024)

Buy Standard

prEN ISO 10896-2:2024prEN ISO 10896-2:2024
PreviousNext
Draft
prEN ISO 10896-2:2024
English language
79 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN ISO 10896-2:2024
01-julij-2024
Vozila za talni transport - Terenska vozila - Varnostne zahteve in preverjanje- 2.
del: Vozila z vrtljivim mehanizmom (ISO/DIS 10896-2:2024)
Rough-terrain trucks - Safety requirements and verification - Part 2: Slewing trucks
(ISO/DIS 10896-2:2024)
Geländegängige Stapler - Sicherheitstechnische Anforderungen und Verifizierung - Teil
2: Schwenkbare Stapler mit veränderlicher Reichweite (ISO/DIS 10896-2:2024)
Chariots tout-terrain - Exigences de sécurité et vérification - Partie 2: Chariots rotatifs
(ISO/DIS 10896-2:2024)
Ta slovenski standard je istoveten z: prEN ISO 10896-2
ICS:
53.060 Industrijski tovornjaki Industrial trucks
oSIST prEN ISO 10896-2:2024 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 10896-2:2024

---------------------- Page: 2 ----------------------
oSIST prEN ISO 10896-2:2024
DRAFT
International
Standard
ISO/DIS 10896-2
ISO/TC 110/SC 4
Rough-terrain trucks — Safety
Secretariat: AFNOR
requirements and verification —
Voting begins on:
Part 2: 2024-05-13
Slewing trucks
Voting terminates on:
2024-08-05
Chariots tout-terrain — Exigences de sécurité et vérifications —
Partie 2: Chariots rotatifs
ICS: 53.060
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Reference number
ISO/DIS 10896-2:2024(en)
© ISO 2024

---------------------- Page: 3 ----------------------
oSIST prEN ISO 10896-2:2024
DRAFT
ISO/DIS 10896-2:2024(en)
International
Standard
ISO/DIS 10896-2
ISO/TC 110/SC 4
Rough-terrain trucks — Safety
Secretariat: AFNOR
requirements and verification —
Voting begins on:
Part 2:
Slewing trucks
Voting terminates on:
Chariots tout-terrain — Exigences de sécurité et vérifications —
Partie 2: Chariots rotatifs
ICS: 53.060
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
COPYRIGHT PROTECTED DOCUMENT
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
© ISO 2024
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
BE CONSIDERED IN THE LIGHT OF THEIR
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
or ISO’s member body in the country of the requester.
NATIONAL REGULATIONS.
ISO copyright office
RECIPIENTS OF THIS DRAFT ARE INVITED
CP 401 • Ch. de Blandonnet 8
TO SUBMIT, WITH THEIR COMMENTS,
CH-1214 Vernier, Geneva
NOTIFICATION OF ANY RELEVANT PATENT
Phone: +41 22 749 01 11
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland Reference number
ISO/DIS 10896-2:2024(en)
© ISO 2024
© ISO 2024 – All rights reserved
ii

---------------------- Page: 4 ----------------------
oSIST prEN ISO 10896-2:2024
ISO/DIS 10896-2:2024(en)
Contents Page
European foreword .vi
Foreword .viii
Introduction .x
1 Scope .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 1755:2024(Main)
Industrial trucks - Safety requirements and verification - Supplementary requirements for operation in potentially explosive atmospheres
EN 1755:2024

This document is applicable to self-propelled and pedestrian propelled manual and semi-manual industrial trucks as defined in ISO 5053-1:2020 including their load handling devices and attachments (hereafter referred to as trucks) intended for use in potentially explosive atmospheres.
NOTE 1   Attachments mounted on the load carrier or on fork arms which are removable by the user are not considered to be a part of the truck.
This document specifies supplementary technical requirements for the prevention of the ignition of an explosive atmosphere of flammable gases, vapours, mists or dusts by industrial trucks of equipment group II and equipment category 2G, 3G, 2D or 3D.
NOTE 2   The relationship between an equipment category (hereafter referred to as category) and the corresponding zone (area classification) is shown in informative Annex B.
This document does not apply to:
-   trucks of equipment group I;
-   trucks of equipment group II, equipment category 1;
-   trucks intended for use in potentially explosive atmospheres with hybrid mixtures;
-   protective systems.
This document does not apply to trucks intended for use in potentially explosive atmospheres of carbon disulfide (CS2), carbon monoxide (CO) and/or ethylene oxide (C2H4O) due to the special properties of these gases.
Technical requirements relating to lithium-ion batteries and fuel cells as energy sources are not given in this document due to their specific hazards.

  • Standard
    54 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 16307-5:2024(Main)
Industrial trucks - Safety requirements and verification - Part 5: Supplementary requirements for pedestrian-propelled trucks
EN 16307-5:2023

This document gives requirements for the types of industrial trucks specified in the scope of EN ISO 3691-5:2015.
This document is intended to be used in conjunction with EN ISO 3691-5:2015.
This document deals with the following significant hazards, hazardous situations or hazardous events relevant, when it is used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer.
These requirements are supplementary to those stated in EN ISO 3691-5:2015 with the addition of requirements for the following hazards:
-   Electromagnetic immunity (external radiation).
This document partially replaces the following requirements of EN ISO 3691-5:2015:
-   Electrical requirements.
This document defines supplementary requirements to EN ISO 3691-5:2015:
-   protection against crushing, shearing and trapping;
-   information for use (instruction handbook and marking);
-   when operating in potentially explosive atmospheres.
This document does not define supplementary requirements to EN ISO 3691-5:2015:
-   Static electricity;
-   Radiation;
-   General principles for the drafting of instructions;
-   Sales literature.
Annex A (informative) contains the list of significant hazards covered by this document.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 3691-3:2017/A1:2023(Amendment)
Industrial trucks - Safety requirements and verification - Part 3: Additional requirements for trucks with elevating operator position and trucks specifically designed to travel with elevated loads - Amendment 1 (ISO 3691-3:2016/Amd 1:2023)
EN ISO 3691-3:2016/A1:2023

2021-07-26 JF: Through decision 429/2021 taken on 2021-07-08, TC decided to decouple the WI from the EU legislation

  • Amendment
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 3691-4:2023(Main)
Industrial trucks - Safety requirements and verification - Part 4: Driverless industrial trucks and their systems (ISO 3691-4:2023)
EN ISO 3691-4:2023

This document specifies safety requirements and the means for their verification for driverless industrial trucks (hereafter referred to as trucks) and their systems.
Examples of driverless industrial trucks (trucks of ISO 5053-1) can also be known as: "automated guided vehicle", "autonomous mobile robot", "bots", "automated guided cart", "tunnel tugger", "under cart", etc.
This document also contains requirements for driverless industrial trucks which are provided with:
— automatic modes which either require operators' action(s) to initiate or enable such automatic operations;
— the capability to transport one or more riders (which are neither considered as drivers nor as operators);
— additional manual modes which allow operators to operate the truck manually; or
— a maintenance mode which allows manual operation of truck functions for maintenance reasons.
It is not applicable to trucks solely guided by mechanical means (rails, guides, etc.) or to remotely controlled trucks, which are not considered to be driverless trucks.
For the purposes of this document, a driverless industrial truck is a powered truck, which is designed to operate automatically. A driverless truck system comprises the control system, which can be part of the truck and/or separate from it, guidance means and power system. Requirements for power sources are not covered in this document.
The condition of the operating zone has a significant effect on the safe operation of the driverless industrial truck. The preparations of the operating zone to eliminate the associated hazards are specified in Annex A.
This document deals with all significant hazards, hazardous situations or hazardous events during all phases of the life of the truck (ISO 12100:2010, 5.4), as listed in Annex B, relevant to the applicable machines when it is used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer.
It does not give requirements for additional hazards that can occur:
— during operation in severe conditions (e.g. extreme climates, freezer applications, strong magnetic fields);
— during operation in nuclear environments;
— from trucks intended to operate in public zones (in particular ISO 13482);
— during operation on a public road;
— during operation in potentially explosive environments;
— during operation in military applications;
— during operation with specific hygienic requirements;
— during operation in ionizing radiation environments;
— during the transportation of (a) person(s) other than (the) intended rider(s);
— when handling loads the nature of which can lead to dangerous situations (e.g. molten metals, acids/bases, radiating materials);
— for rider positions with elevation function higher than 1 200 mm from the floor/ground to the platform floor.
This document does not contain safety requirements for trailer(s) being towed behind a truck.
This document does not contain safety requirements for elevated operator trucks.
This document is not applicable to trucks manufactured before the date of its publication.

  • Standard
    87 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 16307-3:2023(Main)
Industrial trucks - Safety requirements and verification - Part 3 Supplementary requirements for trucks with elevating operator position and trucks specifically designed to travel with elevated loads (additional requirements to EN 16307-1)
EN 16307-3:2023

This document gives requirements for the types of industrial trucks specified in the scope of EN ISO 3691 3:20161.
This document is intended to be used in conjunction with EN ISO 3691-3:2016. These requirements are supplementary to those stated in EN ISO 3691-3:2016.
This document deals with the following significant hazards, hazardous situations or hazardous events relevant when it is used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer:
-   acceleration, deceleration (kinetic energy);
-   machinery mobility.
This document defines supplementary requirements to EN ISO 3691 1:20152, EN ISO 3691-3:2016 and EN 16307 1:2020:
-   brakes operation without guidance system;
-   operator fall protection;
-   information for use (instruction handbook and marking).
Annex A (informative) contains the list of significant hazards covered by this document.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 3691-2:2023(Main)
Industrial trucks - Safety requirements and verification - Part 2: Self-propelled variable-reach trucks (ISO 3691-2:2023)
EN ISO 3691-2:2023

This document gives safety requirements and the means for their verification for self-propelled industrial variable-reach trucks and variable-reach container handlers/reach stackers as defined in ISO 5053‑1 (hereafter referred to as trucks), equipped with forks or integral load-handling devices for normal industrial duties (e.g. fork arms or means, such as spreaders, for handling containers).
This document does not apply to:
—    rough-terrain variable-reach trucks,
—    rough-terrain variable-reach trucks for handling containers,
—    lorry mounted trucks covered by ISO 20297-1,
—    machines designed primarily for earth-moving (e.g. loaders and dozers), even when their buckets and blades are replaced with forks,
—    machines from which the load can swing freely in all directions.
This document is not applicable to trucks manufactured before the date of its publication.
For the purposes of this document, fork arms and integrated attachments are considered to be a part of the truck, whereas attachments/equipment/tools mounted on the load carrier or on the fork arms which are removable by the user are not. Nevertheless, for interchangeable equipment, which is assembled with the truck by the operator in order to change the function of, or attribute a new function to, the truck, this document does provide requirements for:
—    the interface with the truck,
—    protection of the operator in the normal operating position from crushing and shearing hazards,
—    operating and maintenance instructions,
—    load charts,
—    marking,
—    provision for transportation, and,
—    indicator lights for attachments for lifting containers
Any regional requirements additional to the provisions of this document are addressed in EN 16307-2:2023 and ISO/TS 3691‑8.
This document deals with all significant hazards, hazardous situations or hazardous events, as listed in Annex B, with the exception of the following, relevant to the applicable machines when used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer.
It does not establish requirements for hazards that can occur:
—    during construction;
—    when using trucks on public roads;
—    when operating in potentially explosive atmospheres;
—    when lifting persons; or
—    during dismantling, disabling and scrapping.
This document does not provide requirements for:
—    tools, lifting accessories or removeable attachments, which do not change the function or attribute a new function, mounted on the load carrier or fork arms;
—    attachments/equipment mounted on the load carrier or on the fork arms which are removable by the user and which change the function or attribute a new function, except as stated above;
—    the reliability of control systems and performance requirements for safety related parts of control systems; or
—    the requirement for fitting an enclosed cab, whether pressurized or not.

  • Standard
    55 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 16307-2:2023(Main)
Industrial trucks - Safety requirements and verification - Part 2: Supplementary requirements for self-propelled variable-reach trucks
EN 16307-2:2023

This document specifies requirements for the types of industrial trucks specified in the scope of EN ISO 3691-2:2023.
This document is intended to be used in conjunction with EN ISO 3691 2:2023. These requirements are supplementary to those stated in EN ISO 3691-2:2023.
This document deals with the following supplementary requirements and significant hazards, hazardous situations or hazardous events relevant, when it is used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer:
-   electrical requirements;
-   noise emissions;
-   vibration;
-   electromagnetic radiation.
This document specifies supplementary requirements to EN ISO 3691-2:2023:
-   operator's seat;
-   protection against crushing, shearing and trapping;
-   longitudinal stability determination;
-   visibility;
-   information for use (instruction handbook and marking).
Annex A (informative) contains the list of significant hazards covered by this document.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1757:2022(Main)
Safety of industrial trucks - Pedestrian controlled manual platform trucks
EN 1757:2022

8. Scope
1.1   This European Standard applies to pedestrian propelled industrial platform trucks as defined in clause 3.1 with a rated    capacity up to and including 500 kg, hereinafter referred to as "trucks" and designed for general purposes.
1.2   This standard does not apply to:
-   shopping trolleys referred to in EN 1929 Parts 1 to 6 (CEN/TC 291);
-   roll containers referred to in EN 12674 Parts 1 to 4 (CEN/TC 261);
-   trucks that are intended to be towed by powered vehicles, e.g. milk-run-trains/train of trailers/Routenzüge.
1.3   This standard deals with the technical requirements to minimise the hazards listed in clause 4 which can arise during    commissioning, operation and maintenance of trucks when carried out in accordance with the specifications as intended by    the manufacturer.
1.4   This standard does not establish the additional requirements for:
-   operation in severe conditions (e.g. extreme environmental conditions such as: freezer applications, high temperatures,    corrosive environment);
-   operation subject to special rules (e.g. potentially explosive atmospheres);
-   handling of loads the nature of which could lead to dangerous situations (e.g. molten metal, acids/alcalies, radiating    materials, specially brittle loads);
-   hazards occurring during construction, transportation, decommissioning and disposal;
-   direct contact with foodstuffs;
-   operation on gradients or on surfaces other than smooth, level, hard surfaces;
-   trucks designed for special applications : trucks used in hospitals, dinner, trolley;
-   trucks fitted with hinged or sliding doors.
1.5   Other possible limitations of the scope of other standards referred to that also apply to this standard.
1.6   Hazards relevant to visibility and static electricity are not dealt with in this standard.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 3691-6:2022(Main)
Industrial trucks - Safety requirements and verification - Part 6: Burden and personnel carriers (ISO 3691-6:2021)
EN ISO 3691-6:2021

This document gives safety requirements and the means for their verification for self-propelled
carriers designed for carrying burdens without lifting, as defined in ISO 5053-1:2020, and/or personnel
carriers, having three or more wheels, a maximum speed not exceeding 56 km/h and a load capacity
not exceeding 5 000 kg (hereafter referred to as carriers or trucks).
This document is applicable to trucks equipped with a platform (which can be tilting) for the purpose of
carrying materials or with a number of seats for the purpose of transporting passengers.
It is not applicable to:
— vehicles intended primarily for earth-moving or over-the-road hauling;
— driverless trucks;
— pedestrian controlled trucks;
— golf cars;
— tractors with a drawbar pull up to and including 20 000 N equipped with a platform for the purpose
of carrying materials.
This document deals with all significant hazards, hazardous situations or hazardous events, as listed
in Annex A, relevant to the applicable machines when used as intended and under conditions of misuse
which are reasonably foreseeable by the manufacturer.
This document does not deal with hazard due to the risk of break-up during operation.
It does not establish requirements for hazards that can occur when using trucks on public roads or
when operating in potentially explosive atmospheres.
It does not establish requirements to provide fire extinguishers.
Regional requirements, additional to the requirements given in this document, are addressed in
EN 16307-6:2014 and ISO/TS 3691-8:2019.

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 18063-2:2021(Main)
Rough-terrain trucks - Visibility test methods and their verification - Part 2: Slewing trucks (ISO 18063-2: 2021)
EN ISO 18063-2:2021

This standard applies to rough-terrain slewing variable-reach trucks (herein-after referred to as ‘trucks’) as defined in ISO 10896-2 that have a specific seated operator’s position, on the left hand side of the boom, or centre position (excluding operator position on the right side of the boom).
This standard specifies a static test method for determining and evaluating the operator’s visibility on a rectangular 1 m boundary close around the slewing rough-terrain variable-reach truck and on a 12 m visibility test circle. Performance requirements for visibility are specified in this standard.
It applies to trucks for operation on work sites.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day