Digital Enhanced Cordless Telecommunications (DECT) - Common Interface (CI) - Part 2: Physical Layer (PHL)

The present document is one of the parts of the specification of the Digital Enhanced Cordless Telecommunications
(DECT) Common Interface (CI).
The present document specifies the physical channel arrangements. DECT physical channels are radio communication
paths between two radio end points. A radio end point is either part of the fixed infrastructure, a privately owned Fixed
Part (FP), typically a base station, or a Portable Part (PP), typically a handset. The assignment of one or more particular
physical channels to a call is the task of higher layers.
The Physical Layer (PHL) interfaces with the Medium Access Control (MAC) layer, and with the Lower Layer
Management Entity (LLME). On the other side of the PHL is the radio transmission medium which has to be shared
extensively with other DECT users and a wide variety of other radio services. The tasks of the PHL can be grouped into
five categories:
a) to modulate and demodulate radio carriers with a bit stream of a defined rate to create a radio frequency
channel;
b) to acquire and maintain bit and slot synchronization between transmitters and receivers;
c) to transmit or receive a defined number of bits at a requested time and on a particular frequency;
d) to add and remove the synchronization field and the Z-field used for rear end collision detection;
e) to observe the radio environment to report signal strengths.
The present document includes New Generation DECT, a further development of the DECT standard introducing
wideband speech, improved data services, new slot types and other technical enhancements.

Digitalne izboljšane brezvrvične telekomunikacije (DECT) - Skupni vmesnik (CI) - 2. del: Fizična plast (PHL)

Ta dokument je eden od delov specifikacije skupnega vmesnika (CI) za digitalne izboljšane brezvrvične telekomunikacije (DECT). Dokument določa ureditve fizičnega kanala. Fizični kanali digitalnih izboljšanih brezvrvičnih telekomunikacij so poti radijske komunikacije med dvema radijskima končnima točkama. Radijska končna točka je del fiksne strukture, tj. fiksni del (FP) v zasebni lasti – običajno bazna postaja, ali prenosni del (PP) – običajno slušalka. Dodelitev enega ali več določenih fizičnih kanalov klicu je opravilo, ki ga izvajajo višje plasti. Fizična plast (PHL) je povezana s plastjo krmiljenja dostopa do prenosnega medija (MAC) in entiteto upravljanja nižjih plasti (LLME). Na drugi strani fizične plasti je medij za radijski prenos, ki je namenjen obsežni skupni uporabi več uporabnikov digitalnih izboljšanih brezvrvičnih telekomunikacij in različnim radijskim storitvam. Opravila fizične plasti je mogoče združiti v pet kategorij: a) modulacija in demodulacija radijskih nosilcev z bitnim pretokom določene stopnje za ustvarjanje radiofrekvenčnega kanala; b) pridobivanje ter vzdrževanje bitne in režne sinhronizacije med oddajniki ter prejemniki; c) oddajanje ali prejemanje določenega števila bitov ob zahtevanem času in na določeni frekvenci; d) dodajanje in odstranjevanje polja sinhronizacije ter polja Z, ki se uporablja za zaznavanje trka v zadnji del vozila; e) opazovanje radijskega okolja za sporočanje moči signala. Ta dokument vključuje novo generacijo digitalnih izboljšanih brezvrvičnih telekomunikacij, nadaljnji razvoj standarda o digitalnih izboljšanih brezvrvičnih telekomunikacijah, ki uvaja širokopasovni govor, izpopolnjene podatkovne storitve, nove tipe rež in druge tehnične izpopolnitve.

General Information

Status
Published
Public Enquiry End Date
22-Mar-2022
Publication Date
05-Apr-2022
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
04-Apr-2022
Due Date
09-Jun-2022
Completion Date
06-Apr-2022

Buy Standard

Standard
ETSI EN 300 175-2 V2.9.1 (2022-03) - Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI); Part 2: Physical Layer (PHL)
English language
68 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
SIST EN 300 175-2 V2.9.1:2022
English language
68 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
oSIST prEN 300 175-2 V2.8.5:2022
English language
68 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (sample)

ETSI EN 300 175-2 V2.9.1 (2022-03)
EUROPEAN STANDARD
Digital Enhanced Cordless Telecommunications (DECT);
Common Interface (CI);
Part 2: Physical Layer (PHL)
---------------------- Page: 1 ----------------------
2 ETSI EN 300 175-2 V2.9.1 (2022-03)
Reference
REN/DECT-00352
Keywords
DECT, IMT-2000, mobility, radio, TDD, TDMA
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search

The present document may be made available in electronic versions and/or in print. The content of any electronic and/or

print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any

existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI

deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.

Users of the present document should be aware that the document may be subject to revision or change of status.

Information on the current status of this and other ETSI documents is available at

https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx

If you find errors in the present document, please send your comment to one of the following services:

https://portal.etsi.org/People/CommiteeSupportStaff.aspx

If you find a security vulnerability in the present document, please report it through our

Coordinated Vulnerability Disclosure Program:
https://www.etsi.org/standards/coordinated-vulnerability-disclosure
Notice of disclaimer & limitation of liability

The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of

experience to understand and interpret its content in accordance with generally accepted engineering or

other professional standard and applicable regulations.

No recommendation as to products and services or vendors is made or should be implied.

In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.

Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not

limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property

rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages

for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use

of or inability to use the software.
Copyright Notification

No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and

microfilm except as authorized by written permission of ETSI.

The content of the PDF version shall not be modified without the written authorization of ETSI.

The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2022.
All rights reserved.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 300 175-2 V2.9.1 (2022-03)
Contents

Intellectual Property Rights ................................................................................................................................ 7

Foreword ............................................................................................................................................................. 7

Modal verbs terminology .................................................................................................................................... 7

1 Scope ........................................................................................................................................................ 8

2 References ................................................................................................................................................ 8

2.1 Normative references ......................................................................................................................................... 8

2.2 Informative references ........................................................................................................................................ 9

3 Definition of terms, symbols and abbreviations ..................................................................................... 10

3.1 Terms ................................................................................................................................................................ 10

3.2 Symbols ............................................................................................................................................................ 11

3.3 Abbreviations ................................................................................................................................................... 11

4 PHL services .......................................................................................................................................... 12

4.0 General ............................................................................................................................................................. 12

4.1 RF channels (access in frequency) ................................................................................................................... 13

4.1.1 Nominal position of RF carriers ................................................................................................................. 13

4.1.2 Accuracy and stability of RF carriers ......................................................................................................... 14

4.2 Time Division Multiple Access (TDMA) structure (access in time) ................................................................ 14

4.2.1 Frame, full-slot, double-slot, half-slot and variable capacity slot structure (including long slot) ............... 14

4.2.2 Reference timer accuracy and stability ....................................................................................................... 16

4.2.3 RFP transmission jitter................................................................................................................................ 16

4.2.4 PP reference timer synchronization ............................................................................................................ 16

4.2.5 System synchronization .............................................................................................................................. 17

4.2.6 Inter-system synchronization ...................................................................................................................... 17

4.2.7 Reference timer adjustment for synchronization ........................................................................................ 17

4.3 Cells (access in space) ...................................................................................................................................... 17

4.4 Physical packets ............................................................................................................................................... 17

4.4.0 General ........................................................................................................................................................ 17

4.4.1 The short physical packet P00 .................................................................................................................... 18

4.4.2 The basic physical packet P32 .................................................................................................................... 18

4.4.3 The variable capacity physical packet P00j ................................................................................................ 18

4.4.4 The high capacity physical packet P80 ....................................................................................................... 19

4.5 Physical channels ............................................................................................................................................. 19

4.5.0 General ........................................................................................................................................................ 19

4.5.1 Ra (K, L, M, N) notation ............................................................................................................................ 20

4.5.2 The short physical channel R00 (K, L, M, N) ............................................................................................. 20

4.5.3 The basic physical channel R32 (K, L, M, N) ............................................................................................ 21

4.5.4 The variable-rate physical channel R00j (K, L, M, N) ............................................................................... 21

4.5.5 The high capacity physical channel R80 (K, L, M, N) ............................................................................... 22

4.6 Synchronization field S .................................................................................................................................... 23

4.7 D-field .............................................................................................................................................................. 23

4.7.1 Physical packet P00 .................................................................................................................................... 23

4.7.2 Physical packet P32 .................................................................................................................................... 23

4.7.3 Physical packet P00j ................................................................................................................................... 24

4.7.4 Physical packet P80 .................................................................................................................................... 24

4.8 Z-field ............................................................................................................................................................... 24

4.9 Bit pattern during ramping ............................................................................................................................... 25

5 Transmission of physical packets ........................................................................................................... 25

5.1 Definitions ........................................................................................................................................................ 25

5.1.1 End of the physical packet .......................................................................................................................... 25

5.1.2 Transmitted power ...................................................................................................................................... 25

5.1.3 Normal Transmitted Power (NTP) .............................................................................................................. 25

5.2 Transmission burst ........................................................................................................................................... 25

5.2.0 General ........................................................................................................................................................ 25

5.2.1 Transmitter attack time ............................................................................................................................... 25

ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 300 175-2 V2.9.1 (2022-03)

5.2.2 Transmitter release time .............................................................................................................................. 25

5.2.3 Minimum power ......................................................................................................................................... 26

5.2.4 Maximum power ......................................................................................................................................... 26

5.2.5 Maintenance of transmission after packet end ............................................................................................ 26

5.2.6 Transmitter idle power output ..................................................................................................................... 26

5.3 Transmitted power ............................................................................................................................................ 26

5.3.1 Peak power per transceiver ......................................................................................................................... 26

5.3.1.1 PP and RFP with an integral antenna .................................................................................................... 26

5.3.1.2 PP and RFP with external connections for all antennas ........................................................................ 27

5.3.2 Maximum EIRP and number of transceivers .............................................................................................. 27

5.4 RF carrier modulation ...................................................................................................................................... 27

5.4.1 Modulation method ..................................................................................................................................... 27

5.4.2 Definition of "1" and "0" ............................................................................................................................ 27

5.4.3 Deviation limits .......................................................................................................................................... 27

5.5 Unwanted RF power radiation .......................................................................................................................... 28

5.5.1 Emissions due to modulation ...................................................................................................................... 28

5.5.2 Emissions due to transmitter transients ....................................................................................................... 28

5.5.3 Emissions due to intermodulation ............................................................................................................... 28

5.5.4 Spurious emissions when allocated a transmit channel .............................................................................. 28

6 Reception of physical packets ................................................................................................................ 29

6.1 Definitions and conditions for clause 6 ............................................................................................................ 29

6.1.1 Power levels and field strength ................................................................................................................... 29

6.1.2 Test conditions ............................................................................................................................................ 29

6.1.3 Reference DECT radio end point ................................................................................................................ 30

6.2 Radio receiver sensitivity ................................................................................................................................. 30

6.3 Radio receiver reference bit error rate and frame error ratio ............................................................................ 30

6.4 Radio receiver interference performance.......................................................................................................... 30

6.5 Radio receiver blocking .................................................................................................................................... 31

6.5.1 Owing to signals occurring at the same time but on other frequencies ....................................................... 31

6.5.2 Owing to signals occurring at a different time ............................................................................................ 31

6.6 Receiver intermodulation performance ............................................................................................................ 31

6.7 Spurious emissions when not allocated a transmit channel .............................................................................. 32

6.7.1 Out of band ................................................................................................................................................. 32

6.7.2 In the DECT band ....................................................................................................................................... 32

7 Primitives between physical layer and other entities ............................................................................. 32

7.0 General ............................................................................................................................................................. 32

7.1 Medium access control layer (D-SAP) ............................................................................................................. 32

7.1.0 D-SAP general ............................................................................................................................................ 32

7.1.1 PL_TX {req} .............................................................................................................................................. 33

7.1.2 PL_RX {req, cfm} ...................................................................................................................................... 33

7.1.3 PL_FREQ_ADJ {req} ................................................................................................................................ 33

7.2 Management entity (PM-SAP) ......................................................................................................................... 33

7.2.0 PM-SAP general ......................................................................................................................................... 33

7.2.1 PL_ME_SYNC {req, cfm} ......................................................................................................................... 34

7.2.2 PL_ME_SIG_STR {req, cfm} .................................................................................................................... 34

7.2.3 PL_ME_TIME_ADJ {req, cfm} ................................................................................................................. 34

8 PHL procedures ...................................................................................................................................... 34

8.1 Addition of synchronization field and transmission ......................................................................................... 34

8.2 Packet reception and removal of synchronization field .................................................................................... 34

8.3 Measurement of signal strength ........................................................................................................................ 35

8.4 Synchronization pulse detection ....................................................................................................................... 35

8.5 Timing adjustment ............................................................................................................................................ 35

8.6 Frequency adjustment ....................................................................................................................................... 35

9 Management entity procedures related to PHL ...................................................................................... 36

9.1 List of quietest physical channels ..................................................................................................................... 36

9.2 Physical channels with greatest field strength (PP only) .................................................................................. 36

9.3 Extract timing ................................................................................................................................................... 36

Annex A (informative): RF exposure requirements ............................................................................ 37

ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 300 175-2 V2.9.1 (2022-03)

A.0 General ................................................................................................................................................... 37

A.1 Recommendation .................................................................................................................................... 37

A.2 Compliance distances ............................................................................................................................. 37

Annex B (normative): Synchronization port ..................................................................................... 39

B.1 General requirements ............................................................................................................................. 39

B.2 Wired synchronization ports .................................................................................................................. 39

B.2.0 Wired synchronization general ......................................................................................................................... 39

B.2.1 Synchronization signal ..................................................................................................................................... 40

B.3 GPS synchronization .............................................................................................................................. 41

B.3.0 GPS synchronization general ........................................................................................................................... 41

B.3.1 Synchronization signal ..................................................................................................................................... 42

B.3.2 DECT timings derivation from the GPS time................................................................................................... 42

B.3.2.0 Timings derivation general ......................................................................................................................... 42

B.3.2.1 DECT multiframe number synchronization using GPS .............................................................................. 43

B.3.2.2 DECT PSCN synchronization using GPS ................................................................................................... 43

B.4 Guidance for installation ........................................................................................................................ 44

B.4.1 Interconnection cable ....................................................................................................................................... 44

B.4.2 Propagation delay of synchronization signals .................................................................................................. 44

B.4.2.1 Calculation of Propagation delay (informative) .......................................................................................... 44

B.4.2.2 Delay compensation .................................................................................................................................... 45

B.4.3 GPS receiver stability ....................................................................................................................................... 45

Annex C (informative): Prolonged preamble ....................................................................................... 46

C.0 General ................................................................................................................................................... 46

C.1 Bit pattern ............................................................................................................................................... 46

C.2 The power-time template........................................................................................................................ 46

Annex D (normative): 4-level/8-level/16-level/64-level modulation option ..................................... 47

D.0 General ................................................................................................................................................... 47

D.1 The π/2-DBPSK modulation scheme ..................................................................................................... 48

D.1.1 RF carrier modulation ...................................................................................................................................... 48

D.1.1.0 Filter and phase change ............................................................................................................................... 48

D.1.1.1 Modulation accuracy................................................................................................................................... 49

D.1.2 Transmission of physical packets ..................................................................................................................... 49

D.2 The π/4-DQPSK modulation scheme ..................................................................................................... 49

D.2.1 RF carrier modulation ...................................................................................................................................... 49

D.2.1.0 Filter and phase change ............................................................................................................................... 49

D.2.1.1 Modulation accuracy................................................................................................................................... 49

D.2.2 Transmission of physical packets ..................................................................................................................... 49

D.3 The π/8-D8PSK modulation scheme ...................................................................................................... 50

D.3.1 RF carrier modulation ...................................................................................................................................... 50

D.3.1.0 Filter and phase change ............................................................................................................................... 50

D.3.1.1 Modulation accuracy................................................................................................................................... 50

D.3.2 Transmission of physical packets ..................................................................................................................... 50

D.4 The 16-QAM modulation scheme .......................................................................................................... 50

D.4.1 RF carrier modulation ...................................................................................................................................... 50

D.4.1.0 Filter and constellation symbols ................................................................................................................. 50

D.4.1.1 Modulation accuracy................................................................................................................................... 51

D.4.2 Transmission of physical packets ..................................................................................................................... 51

D.5 The 64-QAM modulation scheme .......................................................................................................... 51

D.5.1 RF carrier modulation ...................................................................................................................................... 51

ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 300 175-2 V2.9.1 (2022-03)

D.5.1.0 Filter and constellation symbols ................................................................................................................. 51

D.5.1.1 Modulation accuracy................................................................................................................................... 52

D.5.2 Transmission of physical packets ..................................................................................................................... 53

D.6 Transmission of physical packets ........................................................................................................... 53

D.6.1 Error vector magnitude definition .................................................................................................................... 53

D.6.2 EVM requirement ..........................................................................................................................

...

SLOVENSKI STANDARD
SIST EN 300 175-2 V2.9.1:2022
01-maj-2022

Digitalne izboljšane brezvrvične telekomunikacije (DECT) - Skupni vmesnik (CI) - 2.

del: Fizična plast (PHL)

Digital Enhanced Cordless Telecommunications (DECT) - Common Interface (CI) - Part

2: Physical Layer (PHL)
Ta slovenski standard je istoveten z: ETSI EN 300 175-2 V2.9.1 (2022-03)
ICS:
33.070.30 Digitalne izboljšane Digital Enhanced Cordless
brezvrvične telekomunikacije Telecommunications (DECT)
(DECT)
35.100.10 Fizični sloj Physical layer
SIST EN 300 175-2 V2.9.1:2022 en

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 300 175-2 V2.9.1:2022
---------------------- Page: 2 ----------------------
SIST EN 300 175-2 V2.9.1:2022
ETSI EN 300 175-2 V2.9.1 (2022-03)
EUROPEAN STANDARD
Digital Enhanced Cordless Telecommunications (DECT);
Common Interface (CI);
Part 2: Physical Layer (PHL)
---------------------- Page: 3 ----------------------
SIST EN 300 175-2 V2.9.1:2022
2 ETSI EN 300 175-2 V2.9.1 (2022-03)
Reference
REN/DECT-00352
Keywords
DECT, IMT-2000, mobility, radio, TDD, TDMA
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search

The present document may be made available in electronic versions and/or in print. The content of any electronic and/or

print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any

existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI

deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.

Users of the present document should be aware that the document may be subject to revision or change of status.

Information on the current status of this and other ETSI documents is available at

https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx

If you find errors in the present document, please send your comment to one of the following services:

https://portal.etsi.org/People/CommiteeSupportStaff.aspx

If you find a security vulnerability in the present document, please report it through our

Coordinated Vulnerability Disclosure Program:
https://www.etsi.org/standards/coordinated-vulnerability-disclosure
Notice of disclaimer & limitation of liability

The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of

experience to understand and interpret its content in accordance with generally accepted engineering or

other professional standard and applicable regulations.

No recommendation as to products and services or vendors is made or should be implied.

In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.

Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not

limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property

rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages

for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use

of or inability to use the software.
Copyright Notification

No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and

microfilm except as authorized by written permission of ETSI.

The content of the PDF version shall not be modified without the written authorization of ETSI.

The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2022.
All rights reserved.
ETSI
---------------------- Page: 4 ----------------------
SIST EN 300 175-2 V2.9.1:2022
3 ETSI EN 300 175-2 V2.9.1 (2022-03)
Contents

Intellectual Property Rights ................................................................................................................................ 7

Foreword ............................................................................................................................................................. 7

Modal verbs terminology .................................................................................................................................... 7

1 Scope ........................................................................................................................................................ 8

2 References ................................................................................................................................................ 8

2.1 Normative references ......................................................................................................................................... 8

2.2 Informative references ........................................................................................................................................ 9

3 Definition of terms, symbols and abbreviations ..................................................................................... 10

3.1 Terms ................................................................................................................................................................ 10

3.2 Symbols ............................................................................................................................................................ 11

3.3 Abbreviations ................................................................................................................................................... 11

4 PHL services .......................................................................................................................................... 12

4.0 General ............................................................................................................................................................. 12

4.1 RF channels (access in frequency) ................................................................................................................... 13

4.1.1 Nominal position of RF carriers ................................................................................................................. 13

4.1.2 Accuracy and stability of RF carriers ......................................................................................................... 14

4.2 Time Division Multiple Access (TDMA) structure (access in time) ................................................................ 14

4.2.1 Frame, full-slot, double-slot, half-slot and variable capacity slot structure (including long slot) ............... 14

4.2.2 Reference timer accuracy and stability ....................................................................................................... 16

4.2.3 RFP transmission jitter................................................................................................................................ 16

4.2.4 PP reference timer synchronization ............................................................................................................ 16

4.2.5 System synchronization .............................................................................................................................. 17

4.2.6 Inter-system synchronization ...................................................................................................................... 17

4.2.7 Reference timer adjustment for synchronization ........................................................................................ 17

4.3 Cells (access in space) ...................................................................................................................................... 17

4.4 Physical packets ............................................................................................................................................... 17

4.4.0 General ........................................................................................................................................................ 17

4.4.1 The short physical packet P00 .................................................................................................................... 18

4.4.2 The basic physical packet P32 .................................................................................................................... 18

4.4.3 The variable capacity physical packet P00j ................................................................................................ 18

4.4.4 The high capacity physical packet P80 ....................................................................................................... 19

4.5 Physical channels ............................................................................................................................................. 19

4.5.0 General ........................................................................................................................................................ 19

4.5.1 Ra (K, L, M, N) notation ............................................................................................................................ 20

4.5.2 The short physical channel R00 (K, L, M, N) ............................................................................................. 20

4.5.3 The basic physical channel R32 (K, L, M, N) ............................................................................................ 21

4.5.4 The variable-rate physical channel R00j (K, L, M, N) ............................................................................... 21

4.5.5 The high capacity physical channel R80 (K, L, M, N) ............................................................................... 22

4.6 Synchronization field S .................................................................................................................................... 23

4.7 D-field .............................................................................................................................................................. 23

4.7.1 Physical packet P00 .................................................................................................................................... 23

4.7.2 Physical packet P32 .................................................................................................................................... 23

4.7.3 Physical packet P00j ................................................................................................................................... 24

4.7.4 Physical packet P80 .................................................................................................................................... 24

4.8 Z-field ............................................................................................................................................................... 24

4.9 Bit pattern during ramping ............................................................................................................................... 25

5 Transmission of physical packets ........................................................................................................... 25

5.1 Definitions ........................................................................................................................................................ 25

5.1.1 End of the physical packet .......................................................................................................................... 25

5.1.2 Transmitted power ...................................................................................................................................... 25

5.1.3 Normal Transmitted Power (NTP) .............................................................................................................. 25

5.2 Transmission burst ........................................................................................................................................... 25

5.2.0 General ........................................................................................................................................................ 25

5.2.1 Transmitter attack time ............................................................................................................................... 25

ETSI
---------------------- Page: 5 ----------------------
SIST EN 300 175-2 V2.9.1:2022
4 ETSI EN 300 175-2 V2.9.1 (2022-03)

5.2.2 Transmitter release time .............................................................................................................................. 25

5.2.3 Minimum power ......................................................................................................................................... 26

5.2.4 Maximum power ......................................................................................................................................... 26

5.2.5 Maintenance of transmission after packet end ............................................................................................ 26

5.2.6 Transmitter idle power output ..................................................................................................................... 26

5.3 Transmitted power ............................................................................................................................................ 26

5.3.1 Peak power per transceiver ......................................................................................................................... 26

5.3.1.1 PP and RFP with an integral antenna .................................................................................................... 26

5.3.1.2 PP and RFP with external connections for all antennas ........................................................................ 27

5.3.2 Maximum EIRP and number of transceivers .............................................................................................. 27

5.4 RF carrier modulation ...................................................................................................................................... 27

5.4.1 Modulation method ..................................................................................................................................... 27

5.4.2 Definition of "1" and "0" ............................................................................................................................ 27

5.4.3 Deviation limits .......................................................................................................................................... 27

5.5 Unwanted RF power radiation .......................................................................................................................... 28

5.5.1 Emissions due to modulation ...................................................................................................................... 28

5.5.2 Emissions due to transmitter transients ....................................................................................................... 28

5.5.3 Emissions due to intermodulation ............................................................................................................... 28

5.5.4 Spurious emissions when allocated a transmit channel .............................................................................. 28

6 Reception of physical packets ................................................................................................................ 29

6.1 Definitions and conditions for clause 6 ............................................................................................................ 29

6.1.1 Power levels and field strength ................................................................................................................... 29

6.1.2 Test conditions ............................................................................................................................................ 29

6.1.3 Reference DECT radio end point ................................................................................................................ 30

6.2 Radio receiver sensitivity ................................................................................................................................. 30

6.3 Radio receiver reference bit error rate and frame error ratio ............................................................................ 30

6.4 Radio receiver interference performance.......................................................................................................... 30

6.5 Radio receiver blocking .................................................................................................................................... 31

6.5.1 Owing to signals occurring at the same time but on other frequencies ....................................................... 31

6.5.2 Owing to signals occurring at a different time ............................................................................................ 31

6.6 Receiver intermodulation performance ............................................................................................................ 31

6.7 Spurious emissions when not allocated a transmit channel .............................................................................. 32

6.7.1 Out of band ................................................................................................................................................. 32

6.7.2 In the DECT band ....................................................................................................................................... 32

7 Primitives between physical layer and other entities ............................................................................. 32

7.0 General ............................................................................................................................................................. 32

7.1 Medium access control layer (D-SAP) ............................................................................................................. 32

7.1.0 D-SAP general ............................................................................................................................................ 32

7.1.1 PL_TX {req} .............................................................................................................................................. 33

7.1.2 PL_RX {req, cfm} ...................................................................................................................................... 33

7.1.3 PL_FREQ_ADJ {req} ................................................................................................................................ 33

7.2 Management entity (PM-SAP) ......................................................................................................................... 33

7.2.0 PM-SAP general ......................................................................................................................................... 33

7.2.1 PL_ME_SYNC {req, cfm} ......................................................................................................................... 34

7.2.2 PL_ME_SIG_STR {req, cfm} .................................................................................................................... 34

7.2.3 PL_ME_TIME_ADJ {req, cfm} ................................................................................................................. 34

8 PHL procedures ...................................................................................................................................... 34

8.1 Addition of synchronization field and transmission ......................................................................................... 34

8.2 Packet reception and removal of synchronization field .................................................................................... 34

8.3 Measurement of signal strength ........................................................................................................................ 35

8.4 Synchronization pulse detection ....................................................................................................................... 35

8.5 Timing adjustment ............................................................................................................................................ 35

8.6 Frequency adjustment ....................................................................................................................................... 35

9 Management entity procedures related to PHL ...................................................................................... 36

9.1 List of quietest physical channels ..................................................................................................................... 36

9.2 Physical channels with greatest field strength (PP only) .................................................................................. 36

9.3 Extract timing ................................................................................................................................................... 36

Annex A (informative): RF exposure requirements ............................................................................ 37

ETSI
---------------------- Page: 6 ----------------------
SIST EN 300 175-2 V2.9.1:2022
5 ETSI EN 300 175-2 V2.9.1 (2022-03)

A.0 General ................................................................................................................................................... 37

A.1 Recommendation .................................................................................................................................... 37

A.2 Compliance distances ............................................................................................................................. 37

Annex B (normative): Synchronization port ..................................................................................... 39

B.1 General requirements ............................................................................................................................. 39

B.2 Wired synchronization ports .................................................................................................................. 39

B.2.0 Wired synchronization general ......................................................................................................................... 39

B.2.1 Synchronization signal ..................................................................................................................................... 40

B.3 GPS synchronization .............................................................................................................................. 41

B.3.0 GPS synchronization general ........................................................................................................................... 41

B.3.1 Synchronization signal ..................................................................................................................................... 42

B.3.2 DECT timings derivation from the GPS time................................................................................................... 42

B.3.2.0 Timings derivation general ......................................................................................................................... 42

B.3.2.1 DECT multiframe number synchronization using GPS .............................................................................. 43

B.3.2.2 DECT PSCN synchronization using GPS ................................................................................................... 43

B.4 Guidance for installation ........................................................................................................................ 44

B.4.1 Interconnection cable ....................................................................................................................................... 44

B.4.2 Propagation delay of synchronization signals .................................................................................................. 44

B.4.2.1 Calculation of Propagation delay (informative) .......................................................................................... 44

B.4.2.2 Delay compensation .................................................................................................................................... 45

B.4.3 GPS receiver stability ....................................................................................................................................... 45

Annex C (informative): Prolonged preamble ....................................................................................... 46

C.0 General ................................................................................................................................................... 46

C.1 Bit pattern ............................................................................................................................................... 46

C.2 The power-time template........................................................................................................................ 46

Annex D (normative): 4-level/8-level/16-level/64-level modulation option ..................................... 47

D.0 General ................................................................................................................................................... 47

D.1 The π/2-DBPSK modulation scheme ..................................................................................................... 48

D.1.1 RF carrier modulation ...................................................................................................................................... 48

D.1.1.0 Filter and phase change ............................................................................................................................... 48

D.1.1.1 Modulation accuracy................................................................................................................................... 49

D.1.2 Transmission of physical packets ..................................................................................................................... 49

D.2 The π/4-DQPSK modulation scheme ..................................................................................................... 49

D.2.1 RF carrier modulation ...................................................................................................................................... 49

D.2.1.0 Filter and phase change ............................................................................................................................... 49

D.2.1.1 Modulation accuracy................................................................................................................................... 49

D.2.2 Transmission of physical packets ..................................................................................................................... 49

D.3 The π/8-D8PSK modulation scheme ...................................................................................................... 50

D.3.1 RF carrier modulation ...................................................................................................................................... 50

D.3.1.0 Filter and phase change ............................................................................................................................... 50

D.3.1.1 Modulation accuracy................................................................................................................................... 50

D.3.2 Transmission of physical packets ..................................................................................................................... 50

D.4 The 16-QAM modulation scheme .......................................................................................................... 50

D.4.1 RF carrier modulation ...................................................................................................................................... 50

D.4.1.0 Filter and constellation symbols ................................................................................................................. 50

D.4.1.1 Modulation accuracy................................................................................................................................... 51

D.4.2 Transmission of physical packets ..................................................................................................................... 51

D.5 The 64-QAM modulation scheme .......................................................................................................... 51

D.5.1 RF carrier modulation ...................................................................................................................................... 51

ETSI
---------------------- Page: 7 ----------------------
SIST EN 30
...

SLOVENSKI STANDARD
oSIST prEN 300 175-2 V2.8.5:2022
01-marec-2022

Digitalne izboljšane brezvrvične telekomunikacije (DECT) - Skupni vmesnik (CI) - 2.

del: Fizična plast (PHL)

Digital Enhanced Cordless Telecommunications (DECT) - Common Interface (CI) - Part

2: Physical Layer (PHL)
Ta slovenski standard je istoveten z: ETSI EN 300 175-2 V2.8.5 (2021-12)
ICS:
33.070.30 Digitalne izboljšane Digital Enhanced Cordless
brezvrvične telekomunikacije Telecommunications (DECT)
(DECT)
35.100.10 Fizični sloj Physical layer
oSIST prEN 300 175-2 V2.8.5:2022 en

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 300 175-2 V2.8.5:2022
---------------------- Page: 2 ----------------------
oSIST prEN 300 175-2 V2.8.5:2022
Draft ETSI EN 300 175-2 V2.8.5 (2021-12)
EUROPEAN STANDARD
Digital Enhanced Cordless Telecommunications (DECT);
Common Interface (CI);
Part 2: Physical Layer (PHL)
---------------------- Page: 3 ----------------------
oSIST prEN 300 175-2 V2.8.5:2022
2 Draft ETSI EN 300 175-2 V2.8.5 (2021-12)
Reference
REN/DECT-00352
Keywords
DECT, IMT-2000, mobility, radio, TDD, TDMA
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search

The present document may be made available in electronic versions and/or in print. The content of any electronic and/or

print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any

existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI

deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.

Users of the present document should be aware that the document may be subject to revision or change of status.

Information on the current status of this and other ETSI documents is available at

https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx

If you find errors in the present document, please send your comment to one of the following services:

https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Notice of disclaimer & limitation of liability

The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of

experience to understand and interpret its content in accordance with generally accepted engineering or

other professional standard and applicable regulations.

No recommendation as to products and services or vendors is made or should be implied.

In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.

Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not

limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property

rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages

for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use

of or inability to use the software.
Copyright Notification

No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and

microfilm except as authorized by written permission of ETSI.

The content of the PDF version shall not be modified without the written authorization of ETSI.

The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2021.
All rights reserved.
ETSI
---------------------- Page: 4 ----------------------
oSIST prEN 300 175-2 V2.8.5:2022
3 Draft ETSI EN 300 175-2 V2.8.5 (2021-12)
Contents

Intellectual Property Rights ................................................................................................................................ 7

Foreword ............................................................................................................................................................. 7

Modal verbs terminology .................................................................................................................................... 7

1 Scope ........................................................................................................................................................ 8

2 References ................................................................................................................................................ 8

2.1 Normative references ......................................................................................................................................... 8

2.2 Informative references ........................................................................................................................................ 9

3 Definition of terms, symbols and abbreviations ..................................................................................... 10

3.1 Terms ................................................................................................................................................................ 10

3.2 Symbols ............................................................................................................................................................ 11

3.3 Abbreviations ................................................................................................................................................... 11

4 PHL services .......................................................................................................................................... 12

4.0 General ............................................................................................................................................................. 12

4.1 RF channels (access in frequency) ................................................................................................................... 13

4.1.1 Nominal position of RF carriers ................................................................................................................. 13

4.1.2 Accuracy and stability of RF carriers ......................................................................................................... 14

4.2 Time Division Multiple Access (TDMA) structure (access in time) ................................................................ 14

4.2.1 Frame, full-slot, double-slot, half-slot and variable capacity slot structure (including long slot) ............... 14

4.2.2 Reference timer accuracy and stability ....................................................................................................... 16

4.2.3 RFP transmission jitter................................................................................................................................ 16

4.2.4 PP reference timer synchronization ............................................................................................................ 16

4.2.5 System synchronization .............................................................................................................................. 17

4.2.6 Inter-system synchronization ...................................................................................................................... 17

4.2.7 Reference timer adjustment for synchronization ........................................................................................ 17

4.3 Cells (access in space) ...................................................................................................................................... 17

4.4 Physical packets ............................................................................................................................................... 17

4.4.0 General ........................................................................................................................................................ 17

4.4.1 The short physical packet P00 .................................................................................................................... 18

4.4.2 The basic physical packet P32 .................................................................................................................... 18

4.4.3 The variable capacity physical packet P00j ................................................................................................ 18

4.4.4 The high capacity physical packet P80 ....................................................................................................... 19

4.5 Physical channels ............................................................................................................................................. 19

4.5.0 General ........................................................................................................................................................ 19

4.5.1 Ra (K, L, M, N) notation ............................................................................................................................ 20

4.5.2 The short physical channel R00 (K, L, M, N) ............................................................................................. 20

4.5.3 The basic physical channel R32 (K, L, M, N) ............................................................................................ 21

4.5.4 The variable-rate physical channel R00j (K, L, M, N) ............................................................................... 21

4.5.5 The high capacity physical channel R80 (K, L, M, N) ............................................................................... 22

4.6 Synchronization field S .................................................................................................................................... 23

4.7 D-field .............................................................................................................................................................. 23

4.7.1 Physical packet P00 .................................................................................................................................... 23

4.7.2 Physical packet P32 .................................................................................................................................... 23

4.7.3 Physical packet P00j ................................................................................................................................... 24

4.7.4 Physical packet P80 .................................................................................................................................... 24

4.8 Z-field ............................................................................................................................................................... 24

4.9 Bit pattern during ramping ............................................................................................................................... 25

5 Transmission of physical packets ........................................................................................................... 25

5.1 Definitions ........................................................................................................................................................ 25

5.1.1 End of the physical packet .......................................................................................................................... 25

5.1.2 Transmitted power ...................................................................................................................................... 25

5.1.3 Normal Transmitted Power (NTP) .............................................................................................................. 25

5.2 Transmission burst ........................................................................................................................................... 25

5.2.0 General ........................................................................................................................................................ 25

5.2.1 Transmitter attack time ............................................................................................................................... 25

ETSI
---------------------- Page: 5 ----------------------
oSIST prEN 300 175-2 V2.8.5:2022
4 Draft ETSI EN 300 175-2 V2.8.5 (2021-12)

5.2.2 Transmitter release time .............................................................................................................................. 25

5.2.3 Minimum power ......................................................................................................................................... 26

5.2.4 Maximum power ......................................................................................................................................... 26

5.2.5 Maintenance of transmission after packet end ............................................................................................ 26

5.2.6 Transmitter idle power output ..................................................................................................................... 26

5.3 Transmitted power ............................................................................................................................................ 26

5.3.1 Peak power per transceiver ......................................................................................................................... 26

5.3.1.1 PP and RFP with an integral antenna .................................................................................................... 26

5.3.1.2 PP and RFP with external connections for all antennas ........................................................................ 27

5.3.2 Maximum EIRP and number of transceivers .............................................................................................. 27

5.4 RF carrier modulation ...................................................................................................................................... 27

5.4.1 Modulation method ..................................................................................................................................... 27

5.4.2 Definition of "1" and "0" ............................................................................................................................ 27

5.4.3 Deviation limits .......................................................................................................................................... 27

5.5 Unwanted RF power radiation .......................................................................................................................... 28

5.5.1 Emissions due to modulation ...................................................................................................................... 28

5.5.2 Emissions due to transmitter transients ....................................................................................................... 28

5.5.3 Emissions due to intermodulation ............................................................................................................... 28

5.5.4 Spurious emissions when allocated a transmit channel .............................................................................. 28

6 Reception of physical packets ................................................................................................................ 29

6.1 Definitions and conditions for clause 6 ............................................................................................................ 29

6.1.1 Power levels and field strength ................................................................................................................... 29

6.1.2 Test conditions ............................................................................................................................................ 29

6.1.3 Reference DECT radio end point ................................................................................................................ 30

6.2 Radio receiver sensitivity ................................................................................................................................. 30

6.3 Radio receiver reference bit error rate and frame error ratio ............................................................................ 30

6.4 Radio receiver interference performance.......................................................................................................... 30

6.5 Radio receiver blocking .................................................................................................................................... 31

6.5.1 Owing to signals occurring at the same time but on other frequencies ....................................................... 31

6.5.2 Owing to signals occurring at a different time ............................................................................................ 31

6.6 Receiver intermodulation performance ............................................................................................................ 31

6.7 Spurious emissions when not allocated a transmit channel .............................................................................. 32

6.7.1 Out of band ................................................................................................................................................. 32

6.7.2 In the DECT band ....................................................................................................................................... 32

7 Primitives between physical layer and other entities ............................................................................. 32

7.0 General ............................................................................................................................................................. 32

7.1 Medium access control layer (D-SAP) ............................................................................................................. 32

7.1.0 D-SAP general ............................................................................................................................................ 32

7.1.1 PL_TX {req} .............................................................................................................................................. 33

7.1.2 PL_RX {req, cfm} ...................................................................................................................................... 33

7.1.3 PL_FREQ_ADJ {req} ................................................................................................................................ 33

7.2 Management entity (PM-SAP) ......................................................................................................................... 33

7.2.0 PM-SAP general ......................................................................................................................................... 33

7.2.1 PL_ME_SYNC {req, cfm} ......................................................................................................................... 34

7.2.2 PL_ME_SIG_STR {req, cfm} .................................................................................................................... 34

7.2.3 PL_ME_TIME_ADJ {req, cfm} ................................................................................................................. 34

8 PHL procedures ...................................................................................................................................... 34

8.1 Addition of synchronization field and transmission ......................................................................................... 34

8.2 Packet reception and removal of synchronization field .................................................................................... 34

8.3 Measurement of signal strength ........................................................................................................................ 35

8.4 Synchronization pulse detection ....................................................................................................................... 35

8.5 Timing adjustment ............................................................................................................................................ 35

8.6 Frequency adjustment ....................................................................................................................................... 35

9 Management entity procedures related to PHL ...................................................................................... 36

9.1 List of quietest physical channels ..................................................................................................................... 36

9.2 Physical channels with greatest field strength (PP only) .................................................................................. 36

9.3 Extract timing ................................................................................................................................................... 36

Annex A (informative): RF exposure requirements ............................................................................ 37

ETSI
---------------------- Page: 6 ----------------------
oSIST prEN 300 175-2 V2.8.5:2022
5 Draft ETSI EN 300 175-2 V2.8.5 (2021-12)

A.0 General ................................................................................................................................................... 37

A.1 Recommendation .................................................................................................................................... 37

A.2 Compliance distances ............................................................................................................................. 37

Annex B (normative): Synchronization port ..................................................................................... 39

B.1 General requirements ............................................................................................................................. 39

B.2 Wired synchronization ports .................................................................................................................. 39

B.2.0 Wired synchronization general ......................................................................................................................... 39

B.2.1 Synchronization signal ..................................................................................................................................... 40

B.3 GPS synchronization .............................................................................................................................. 41

B.3.0 GPS synchronization general ........................................................................................................................... 41

B.3.1 Synchronization signal ..................................................................................................................................... 42

B.3.2 DECT timings derivation from the GPS time................................................................................................... 42

B.3.2.0 Timings derivation general ......................................................................................................................... 42

B.3.2.1 DECT multiframe number synchronization using GPS .............................................................................. 43

B.3.2.2 DECT PSCN synchronization using GPS ................................................................................................... 43

B.4 Guidance for installation ........................................................................................................................ 44

B.4.1 Interconnection cable ....................................................................................................................................... 44

B.4.2 Propagation delay of synchronization signals .................................................................................................. 44

B.4.2.1 Calculation of Propagation delay (informative) .......................................................................................... 44

B.4.2.2 Delay compensation .................................................................................................................................... 45

B.4.3 GPS receiver stability ....................................................................................................................................... 45

Annex C (informative): Prolonged preamble ....................................................................................... 46

C.0 General ................................................................................................................................................... 46

C.1 Bit pattern ............................................................................................................................................... 46

C.2 The power-time template........................................................................................................................ 46

Annex D (normative): 4-level/8-level/16-level/64-level modulation option ..................................... 47

D.0 General ................................................................................................................................................... 47

D.1 The π/2-DBPSK modulation scheme ..................................................................................................... 48

D.1.1 RF carrier modulation ...................................................................................................................................... 48

D.1.1.0 Filter and phase change ............................................................................................................................... 48

D.1.1.1 Modulation accuracy................................................................................................................................... 49

D.1.2 Transmission of physical packets ..................................................................................................................... 49

D.2 The π/4-DQPSK modulation scheme ..................................................................................................... 49

D.2.1 RF carrier modulation ...................................................................................................................................... 49

D.2.1.0 Filter and phase change ............................................................................................................................... 49

D.2.1.1 Modulation accuracy................................................................................................................................... 49

D.2.2 Transmission of physical packets ..................................................................................................................... 49

D.3 The π/8-D8PSK modulation scheme ...................................................................................................... 50

D.3.1 RF carrier modulation ...................................................................................................................................... 50

D.3.1.0 Filter and phase change ............................................................................................................................... 50

D.3.1.1 Modulation accuracy................................................................................................................................... 50

D.3.2 Transmission of physical packets ..................................................................................................................... 50

D.4 The 16-QAM modulation scheme .......................................................................................................... 50

D.4.1 RF carrier modulation ...................................................................................................................................... 50

D.4.1.0 Filter and constellation symbols ................................................................................................................. 50

D.4.1.1 Modulation accuracy................................................................................................................................... 51

D.4.2 Transmission of physical packets ..................................................................................................................... 51

D.5 The 64-QAM modulation scheme .......................................................................................................... 51

D.5.1 RF carrier modulation ...................................................................................................................................... 51

ETSI
---------------------- Page: 7 ----------------------
oSIST prEN 300 175-2 V2.8.5:2022
6 Draft ETSI EN 300 175-2 V2.8.5 (2021-12)

D.5.1.0 Filter and constellation symbols ...............................................

...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.