iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 61330:2001

(Main)

High-voltage/low-voltage prefabricated substations

High-voltage/low-voltage prefabricated substations

Specifies the service conditions, rated characteristics, general structural requirements and test method of prefabricated substations, which are cable connected, for alternating current of primary rated voltages above 1 kV and up to and including 52 kV1, and for a transformer of maximum power 1 600 kVA, for service frequencies up to and including 60 Hz.

Fabrikfertige Stationen für Hochspannung/Niederspannung

Postes préfabriqués haute tension/basse tension

Fixe les conditions de service, les caractéristiques assignées, les exigences structurelles générales, et les méthodes d'essai applicables aux postes préfabriqués qui sont connectés par câble, pour courant alternatif de tensions primaires assignées supérieures à 1 kV et inférieures ou égales à 52 kV1), pour un transformateur de puissance maximale 1600 kVA, pour des fréquences de service inférieures ou égales à 60 Hz.

High-voltage/low-voltage prefabricated substations

General Information

Status
Withdrawn
Publication Date
28-Feb-2001
Withdrawal Date
16-Dec-2009
ICS
29.240.10 - Substations. Surge arresters
Technical Committee
SKA - Switchgear and control gear
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
10-Dec-2009
Due Date
02-Jan-2010
Completion Date
17-Dec-2009
Ref Project
EN 61330:1996 - High-voltage/low-voltage prefabricated substations

Relations

Revised
SIST EN 62271-202:2007 - High-voltage switchgear and controlgear -- Part 202: High voltage/low voltage prefabricated substation
Effective Date
13-May-2010
Replaced By
SIST EN 62271-202:2007 - High-voltage switchgear and controlgear -- Part 202: High voltage/low voltage prefabricated substation
Effective Date
28-Jan-2023
Replaced By
SIST EN 62271-202:2007 - High-voltage switchgear and controlgear -- Part 202: High voltage/low voltage prefabricated substation
Effective Date
07-Jun-2022

Buy Standard

EN 61330:2001EN 61330:2001
PreviousNext
Standard
EN 61330:2001
English language
51 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 61330:2001
01-marec-2001
High-voltage/low-voltage prefabricated substations
High-voltage/low-voltage prefabricated substations
Fabrikfertige Stationen für Hochspannung/Niederspannung
Postes préfabriqués haute tension/basse tension
Ta slovenski standard je istoveten z: EN 61330:1996
ICS:
29.240.10 Transformatorske postaje. Substations. Surge arresters
Prenapetostni odvodniki
SIST EN 61330:2001 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 61330:2001

---------------------- Page: 2 ----------------------

SIST EN 61330:2001

---------------------- Page: 3 ----------------------

SIST EN 61330:2001

---------------------- Page: 4 ----------------------

SIST EN 61330:2001

---------------------- Page: 5 ----------------------

SIST EN 61330:2001

---------------------- Page: 6 ----------------------

SIST EN 61330:2001

---------------------- Page: 7 ----------------------

SIST EN 61330:2001

---------------------- Page: 8 ----------------------

SIST EN 61330:2001

---------------------- Page: 9 ----------------------

SIST EN 61330:2001

---------------------- Page: 10 ----------------------

SIST EN 61330:2001

---------------------- Page: 11 ----------------------

SIST EN 61330:2001

---------------------- Page: 12 ----------------------

SIST EN 61330:2001

---------------------- Page: 13 ----------------------

SIST EN 61330:2001

---------------------- Page: 14 ----------------------

SIST EN 61330:2001

---------------------- Page: 15 ----------------------

SIST EN 61330:2001

---------------------- Page: 16 ----------------------

SIST EN 61330:2001

---------------------- Page: 17 ----------------------

SIST EN 61330:2001

---------------------- Page: 18 ----------------------

SIST EN 61330:2001

---------------------- Page: 19 ----------------------

SIST EN 61330:2001

---------------------- Page: 20 ----------------------

SIST EN 61330:2001

---------------------- Page: 21 ----------------------

SIST EN 61330:2001

---------------------- Page: 22 ----------------------

SIST EN 61330:2001

---------------------- Page: 23 ----------------------

SIST EN 61330:2001

---------------------- Page: 24 ------------
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST IEC 61643-12:2023(Main)
Low-voltage surge protective devices - Part 12: Surge protective devices connected to low-voltage power systems - Selection and application principles (IEC 61643-12:2020)
IEC 61643-12:2020

IEC 61643-12:2020 describes the principles for the selection, operation, location and coordination of SPDs to be connected to 50/60 Hz AC power circuits, and equipment rated up to 1 000 V RMS. These devices contain at least one non-linear component and are intended to limit surge voltages and divert surge currents.
NOTE 1 Additional requirements for special applications are also applicable, If required.
NOTE 2 IEC 60364 and IEC 62305-4 are also applicable.
NOTE 3 This standard deal only with SPDs and not with surge protection components (SPC) integrated inside equipment.
This third edition cancels and replaces the second edition published in 2008. This edition constitutes a technical revision.
NOTE The following differing practice of a less permanent nature exists in the USA: In the USA, SPDs tested to Class I tests are not required. This exception applies to the entire document. This edition includes the following significant technical changes with respect to the previous edition:
a) Scope: Deleted reference to 1 500 V dc
b) Added or revised some definitions
c) Added new clause 4 on Need for protection
d) Added new information on disconnecting devices
e) Revised Characteristics of SPD
f) Revised List of parameters for SPD selection
g) Added new information on Measured Limiting Voltage
e) Added or revised some Annexes

  • Standard
    207 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    433 pages
    English and French language
    sale 15% off
SIST
SIST EN 61643-31:2019/AC:2022(Corrigendum)
Low-voltage surge protective devices - Part 31: Requirements and test methods for SPDs for photovoltaic installations
EN 61643-31:2019/AC:2022-07

IEC Corrected version

  • Corrigendum
    4 pages
    English and French language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 60099-5:2018(Main)
Surge arresters - Part 5: Selection and application recommendations
EN IEC 60099-5:2018

This part of IEC 60099 provides information, guidance, and recommendations for the
selection and application of surge arresters to be used in three-phase systems with nominal
voltages above 1 kV. It applies to gapless metal-oxide surge arresters as defined in
IEC 60099-4, to surge arresters containing both series and parallel gapped structure – rated
52 kV and less as defined in IEC 60099-6 and metal-oxide surge arresters with external series
gap for overhead transmission and distribution lines (EGLA) as defined in IEC 60099-8. In
Annex J, some aspects regarding the old type of SiC gapped arresters are discussed.
Surge arrester residual voltage is a major parameter to which most users have paid a lot of
attention to when selecting the type and rating. Typical maximum residual voltages are given
in Annex F. It is likely, however, that for some systems, or in some countries, the
requirements on system reliability and design are sufficiently uniform, so that the
recommendations of the present standard may lead to the definition of narrow ranges of
arresters. The user of surge arresters will, in that case, not be required to apply the whole
process introduced here to any new installation and the selection of characteristics resulting
from prior practice may be continued.
Annexes H and I present comparisons and calculations between old line discharge
classification and new charge classification.

  • Standard
    193 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 61643-352:2018(Main)
Components for low-voltage surge protection - Part 352: Selection and application principles for telecommunications and signalling network surge isolation transformers (SIT)
EN IEC 61643-352:2018

This part of IEC 61643 covers the application of surge isolation transformers (SITs) that are
used in telecommunication transformer applications with signal levels up to 400 V peak to
peak. These transformers have a high rated impulse voltage with or without screen between
the input and output windings. SITs are components for surge protection and are used to
mitigate the onward propagation of common-mode voltage surges. This document describes
SITs' selection, application principles and related information. This document does not cover
power line communication transformers.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 61643-11:2012/A11:2018(Amendment)
Low-voltage surge protective devices - Part 11: Surge protective devices connected to low-voltage power systems - Requirements and test methods
EN 61643-11:2012/A11:2018

To add an annex for portable SPDs for household and similar use.
This annex will contain the following specific requirements to ensure the requested level of intrinsic safety for such products, i.e. product tests and safety cannot rely on any external means:
- The position of the disconnector(s) : internal, i.e. all tests shall be made and passed without the help of any external means,
- Additional specifications for tests taking into account that line and neutral terminals can be reversed,
- Specific requirements and tests for surge protective components used with such SPDs

  • Addendum – translation
    7 pages
    Slovenian language
    sale 10% off
    e-Library read for
    1 day
  • Amendment
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 60099-8:2018(Main)
Surge arresters - Part 8: Metal-oxide surge arresters with external series gap (EGLA) for overhead transmission and distribution lines of a.c. systems above 1 kV
EN IEC 60099-8:2018

This part of IEC 60099 covers metal-oxide surge arresters with external series gap (externally
gapped line arresters (EGLA)) that are applied on overhead transmission and distribution
lines, only to protect insulator assemblies from lightning-caused flashovers.
This document defines surge arresters to protect the insulator assembly from lightning-caused
over-voltages only. Therefore, and since metal-oxide resistors are not permanently connected
to the line, the following items are not considered for this document:
• switching impulse spark-over voltage;
• residual voltage at steep current and switching current impulse;
• thermal stability;
• long-duration current impulse withstand duty;
• power-frequency voltage versus time characteristics of an arrester;
• disconnector test;
• aging duties by power-frequency voltage.
Considering the particular design concept and the special application on overhead
transmission and distribution lines, some unique requirements and tests are introduced, such
as the verification test for coordination between insulator withstand and EGLA protective
level, the follow current interrupting test, mechanical load tests, etc.
Designs with the EGLA's external series gap installed in parallel to an insulator are not
covered by this document.

  • Standard
    70 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 61643-351:2017(Main)
Components for lowvoltage surge protective devices - Part 351: Performance requirements and test methods for telecommunications and signalling network surge isolation transformers (SIT)
EN 61643-351:2017

Surge isolation transformers (SITs) are used for signal transformer applications with signal
levels up to 400 V peak to peak. SITs are transformers, with or without an internal-winding
screen, with a rated impulse withstand voltage greater than the peak voltage of the expected
common-mode surge environment. SITs are applicable to components for surge protection
against indirect and direct effects of lightning or other transient overvoltage. SITs are used to
mitigate the onward propagation of common-mode voltage surges. This part of IEC 61643
defines test circuits and test methods for determining and verifying the SIT surge parameters.
Preferred performance values for key parameters are given.
This part of IEC 61643 does not cover SIT operation under differential-mode lightning surge
conditions.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TS CLC/TS 61643-22:2016(Main)
Low-voltage surge protective devices - Part 22: Surge protective devices connected to telecommunications and signalling networks - Selection and application principles
CLC/TS 61643-22:2016

IEC 61643-22:2015 describes the principles for the selection, operation, location and coordination of SPDs connected to telecommunication and signalling networks with nominal system voltages up to 1 000 V r.m.s. a.c. and 1 500 V d.c. This standard also addresses SPDs that incorporate protection for signalling lines and power lines in the same enclosure (so called multiservice SPDs). This second edition cancels and replaces the first edition published in 2004. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- Update the use of multiservice SPDs (Article 8);
- Comparison between SPD classification of IEC 61643-11 and IEC 61643-21 (7.3.3);
- Consideration of new transmission systems as PoE (Annex F);
- EMC requirements of SPDs (Annex G);
- Maintenance cycles of SPDs (Annex I).
Keywords: SPD, surge protective devices

  • Technical specification
    68 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60099-4:2014(Main)
Surge arresters - Part 4: Metal-oxide surge arresters without gaps for a.c. systems
EN 60099-4:2014

EN IEC 60099-4 applies to non-linear metal-oxide resistor type surge arresters without spark gaps designed to limit voltage surges on a.c. power circuits with Us above 1 kV.

  • Standard
    172 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60099-9:2014(Main)
Surge arresters - Part 9: Metal-oxide surge arresters without gaps for HVDC converter stations
EN 60099-9:2014

EN IEC 60099-9 applies to non-linear metal-oxide resistor type surge arresters without spark gaps designed to limit overvoltages in HVDC converter stations of two terminal, multiterminal and back-to-back type up to and including an operating voltage of 1 100 kV. The standard applies in general to porcelain-housed and polymer-housed type arresters but also to gas-insulated metal enclosed arresters (GIS-arresters) solely used as d.c. bus and d.c. line/cable arresters. Arresters for voltage source converters are not covered. Arresters applied on the a.c. systems at the converter station and subjected to power-frequency voltage of 50 or 60 Hz principally without harmonics are tested as per IEC 60099-4. The arresters on a.c.-filters are tested according to this standard.

  • Standard
    92 pages
    English language
    sale 10% off
    e-Library read for
    1 day