SIST EN ISO 14246:2022
(Main)Gas cylinders - Cylinder valves - Manufacturing tests and examinations (ISO 14246:2022)
Gas cylinders - Cylinder valves - Manufacturing tests and examinations (ISO 14246:2022)
This document specifies the procedures and acceptance criteria for manufacturing tests and
examinations (sometimes called "initial inspection and tests") of valves designed and type tested in
accordance with ISO 10297.
This document is applicable to:
a) cylinder valves intended to be fitted to refillable transportable gas cylinders;
b) main valves (excluding ball valves) for cylinder bundles;
c) cylinder valves or main valves with integrated pressure regulator (VIPR);
d) valves for pressure drums and tubes.
NOTE Where there is no risk of ambiguity, cylinder valves, main valves, VIPR and valves for pressure drums
and tubes are addressed with the collective term “valves” within this document.
The principles of these manufacturing tests and examinations can be beneficially applied to cylinder
valves type tested to national or International Standards other than ISO 10297.
Gasflaschen - Flaschenventile - Herstellungsprüfungen und untersuchungen (ISO 14246:2022)
Dieses Dokument legt die Verfahren und Annahmekriterien für Herstellungsprüfungen und untersuchungen (manchmal als „erstmalige Prüfung“ bezeichnet) für Ventile fest, die nach ISO 10297 ausgelegt und baumustergeprüft wurden.
Dieses Dokument gilt für
a) Flaschenventile für wiederbefüllbare ortsbewegliche Gasflaschen,
b) Hauptabsperrventile (ausgenommen Kugelhähne) für Flaschenbündel,
c) Flaschenventile oder Hauptabsperrventile mit integriertem Druckregler (VIPR, en: valve with integrated pressure regulator), und
d) Ventile für Druckfässer und rohre.
ANMERKUNG Sofern keine Gefahr der Mehrdeutigkeit besteht, werden Flaschenventile, Hauptabsperrventile, VIPR und Ventile für Druckfässer und rohre in diesem Dokument zusammengefasst mit dem Begriff „Ventile“ bezeichnet.
Die Grundsätze dieser Herstellungsprüfungen und untersuchungen können nutzbringend auf Flaschenventile angewendet werden, die nach nationalen oder nach von ISO 10297 abweichenden Internationalen Normen baumustergeprüft wurden.
Bouteilles à gaz - Robinets de bouteilles à gaz - Essais de fabrication et contrôles (ISO 14246:2022)
Le présent document décrit les modes opératoires et les critères d’acceptation applicables aux essais de fabrication et aux contrôles (parfois appelés «inspection initiale et essais») des robinets conçus et soumis à des essais de type conformément à l’ISO 10297.
Le présent document s’applique:
a) aux robinets de bouteilles destinés à être montés sur des bouteilles à gaz transportables et rechargeables;
b) aux vannes principales (à l’exception des robinets à boisseau sphérique) pour cadres de bouteilles;
c) aux robinets de bouteilles ou aux robinets principaux avec détendeur intégré (VIPR);
d) aux robinets de fûts à pression et de tubes.
NOTE Lorsqu’il n’y a pas de risque d’ambiguïté, les robinets de bouteilles, les vannes principales, les VIPR et les robinets de fûts à pression et de tubes sont désignés par le terme générique «robinets» dans le présent document.
Les principes de ces essais de fabrication et de ces contrôles peuvent être appliqués avantageusement à des robinets de bouteilles ayant été soumis à des essais de type conformément à des Normes nationales ou internationales autres que l’ISO 10297.
Plinske jeklenke - Ventili za plinske jeklenke - Preskusi in pregledi med proizvodnjo (ISO 14246:2022)
Ta dokument določa postopke in kriterije sprejemljivosti za preskuse in preglede med proizvodnjo (včasih imenovani »začetni pregledni preskusi«) ventilov, ki so bili načrtovani in tipsko preskušeni v skladu s standardom ISO 10297.
Ta dokument se uporablja za:
a) ventile jeklenk, ki so predvideni za namestitev na ponovno polnljive premične plinske jeklenke;
b) glavne ventile (brez krogelnih ventilov) za sklope jeklenk;
c) ventile za jeklenke ali glavne ventile z vgrajenim regulatorjem tlaka (VIPR);
d) ventile za tlačne valje in cevi.
OPOMBA: Če ne obstaja tveganje dvoumnosti, so ventili za jeklenke, glavni ventili, ventili z vgrajenim regulatorjem tlaka in ventili za tlačne valje in cevi v tem dokumentu imenovani s skupnim izrazom »ventili«.
Načela teh preskusov in pregledov med proizvodnjo je mogoče koristno uporabiti za ventile za jeklenke, ki so bili tipsko preskušeni v skladu z nacionalnim ali mednarodnim standardom, ki ni standard ISO 10297.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 14246:2022
01-september-2022
Nadomešča:
SIST EN ISO 14246:2014
SIST EN ISO 14246:2014/A1:2018
Plinske jeklenke - Ventili za plinske jeklenke - Preskusi in pregledi med
proizvodnjo (ISO 14246:2022)
Gas cylinders - Cylinder valves - Manufacturing tests and examinations (ISO
14246:2022)
Gasflaschen - Flaschenventile - Herstellungsprüfungen und untersuchungen (ISO
14246:2022)
Bouteilles à gaz - Robinets de bouteilles à gaz - Essais de fabrication et contrôles (ISO
14246:2022)
Ta slovenski standard je istoveten z: EN ISO 14246:2022
ICS:
23.020.35 Plinske jeklenke Gas cylinders
23.060.40 Tlačni regulatorji Pressure regulators
SIST EN ISO 14246:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 14246:2022
---------------------- Page: 2 ----------------------
SIST EN ISO 14246:2022
EN ISO 14246
EUROPEAN STANDARD
NORME EUROPÉENNE
February 2022
EUROPÄISCHE NORM
ICS 23.020.35 Supersedes EN ISO 14246:2014, EN ISO
14246:2014/A1:2017
English Version
Gas cylinders - Cylinder valves - Manufacturing tests and
examinations (ISO 14246:2022)
Bouteilles à gaz - Robinets de bouteilles à gaz - Essais Gasflaschen - Flaschenventile - Herstellungsprüfungen
de fabrication et contrôles (ISO 14246:2022) und untersuchungen (ISO 14246:2022)
This European Standard was approved by CEN on 13 February 2022.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 14246:2022 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 14246:2022
EN ISO 14246:2022 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 14246:2022
EN ISO 14246:2022 (E)
European foreword
This document (EN ISO 14246:2022) has been prepared by Technical Committee ISO/TC 58 "Gas
cylinders" in collaboration with Technical Committee CEN/TC 23 “Transportable gas cylinders” the
secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by August 2022, and conflicting national standards shall
be withdrawn at the latest by August 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 14246:2014.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 14246:2022 has been approved by CEN as EN ISO 14246:2022 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 14246:2022
---------------------- Page: 6 ----------------------
SIST EN ISO 14246:2022
INTERNATIONAL ISO
STANDARD 14246
Third edition
2022-02
Gas cylinders — Cylinder valves —
Manufacturing tests and examinations
Bouteilles à gaz — Robinets de bouteilles à gaz — Essais de
fabrication et contrôles
Reference number
ISO 14246:2022(E)
© ISO 2022
---------------------- Page: 7 ----------------------
SIST EN ISO 14246:2022
ISO 14246:2022(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
© ISO 2022 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 14246:2022
ISO 14246:2022(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Cleanliness . 2
5 Manufacturing tests and examinations . 2
5.1 General . 2
5.2 Valve test pressure . . 3
5.3 Tests to be performed on each valve . 3
5.4 Inspections and examinations to be performed on a sample and verification of the
batch documentation . 4
5.5 Procedures to verify materials of construction and components . 5
Annex A (informative) Example of test protocol on each valve . 6
Bibliography . 7
iii
© ISO 2022 – All rights reserved
---------------------- Page: 9 ----------------------
SIST EN ISO 14246:2022
ISO 14246:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO’s adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 58, Gas cylinders, Subcommittee SC 2,
Cylinder fittings, in collaboration with the European Committee for Standardization (CEN) Technical
Committee CEN/TC 23, Transportable gas cylinders, in accordance with the Agreement on technical
cooperation between ISO and CEN (Vienna Agreement).
This third edition cancels and replaces the second edition (ISO 14246:2014), which has been technically
revised. It also incorporates Amendment ISO 14246:2014/Amd 1:2017. The main changes are as follows:
2
— in Clause 4, a maximum level of hydrocarbon contamination of 220 mg/m and a maximum particle
size of 200 µm has been introduced for valves for oxygen and other oxidizing gases for general
purpose applications, and the mandatory reference to ISO 15001 has been changed to an example
for medical applications;
— in 5.2, indent c), the value of the test pressure for specific acetylene valves has been reduced from
37 bar to 35 bar;
— in 5.4, the requirements concerning the verification of the assembly with regard to the use of correct
components and assembly torques have been clarified.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
© ISO 2022 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 14246:2022
ISO 14246:2022(E)
Introduction
This document covers the function of a valve as a closure (defined by the UN Model Regulations).
Additional features of valves (e.g. pressure regulators, residual pressure-retaining devices, non-return
devices and pressure relief devices) might be covered by other standards and/or regulations.
Valves conforming to this document can be expected to perform satisfactorily under normal service
conditions.
This document pays particular attention to manufacturing tests and examinations of valves designed
and type tested in accordance with ISO 10297.
[1]
This document has been written so that it is suitable to be refere
...
SLOVENSKI STANDARD
oSIST prEN ISO 14246:2021
01-junij-2021
Plinske jeklenke - Ventili za plinske jeklenke - Preskusi in pregledi med
proizvodnjo (ISO/DIS 14246:2021)
Gas cylinders - Cylinder valves - Manufacturing tests and examinations (ISO/DIS
14246:2021)
Bouteilles à gaz - Robinets de bouteilles à gaz - Essais de fabrication et contrôles
(ISO/DIS 14246:2021)
Ta slovenski standard je istoveten z: prEN ISO 14246
ICS:
23.020.35 Plinske jeklenke Gas cylinders
23.060.40 Tlačni regulatorji Pressure regulators
oSIST prEN ISO 14246:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 14246:2021
---------------------- Page: 2 ----------------------
oSIST prEN ISO 14246:2021
DRAFT INTERNATIONAL STANDARD
ISO/DIS 14246
ISO/TC 58/SC 2 Secretariat: AFNOR
Voting begins on: Voting terminates on:
2021-04-07 2021-06-30
Gas cylinders — Cylinder valves — Manufacturing tests and
examinations
Bouteilles à gaz — Robinets de bouteilles à gaz — Essais de fabrication et contrôles
ICS: 23.020.35
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 14246:2021(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2021
---------------------- Page: 3 ----------------------
oSIST prEN ISO 14246:2021
ISO/DIS 14246:2021(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2021 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 14246:2021
ISO/DIS 14246:2021(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Cleanliness . 2
5 Manufacturing tests and examinations. 2
5.1 General . 2
5.2 Valve test pressure . 2
5.3 Tests to be performed on each valve . 3
5.4 Inspections and examinations to be performed on a sample and verification of the
batch documentation . 4
5.5 Procedures to verify materials of construction and components . 4
Annex A (informative) Example of test protocol on each valve . 5
Bibliography . 6
© ISO 2021 – All rights reserved iii
---------------------- Page: 5 ----------------------
oSIST prEN ISO 14246:2021
ISO/DIS 14246:2021(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 58, Gas cylinders, Subcommittee SC 2,
Cylinder fittings, in collaboration with the European Committee for Standardization (CEN) Technical
Committee CEN/TC 23, Transportable gas cylinders, in accordance with the Agreement on technical
cooperation between ISO and CEN (Vienna Agreement).
This third edition cancels and replaces the second edition (ISO 14246:2014), which has been technically
revised.
The main changes from ISO 14246:2014 are:
— the integration of the 2017 amendment,
2
— in clause 4, a maximum level of hydrocarbon contamination of 220 mg/m and a maximum particle
size of 200 µm was introduced for valves for oxygen and other oxidizing gases for general purpose
applications and the mandatory reference to ISO 15001 was changed to an example for medical
applications,
— in clause 5.2, indent c), the value of the test pressure for specific acetylene valves has been reduced
from 37 bar to 35 bar,
— in clause 5.4, the requirements concerning the verification of the assembly with regard to the use of
correct components and assembly torques were clarified.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2021 – All rights reserved
---------------------- Page: 6 ----------------------
oSIST prEN ISO 14246:2021
ISO/DIS 14246:2021(E)
Introduction
This document covers the function of a valve as a closure (defined by the UN Model Regulations).
Additional features of valves (e.g. pressure regulators, residual pressure-retaining devices, non-return
devices and pressure relief devices) might be covered by other standards and/or regulations.
Valves complying with this document can be expected to perform satisfactorily under normal service
conditions.
This document pays particular attention to manufacturing tests and examinations of valves designed
and type tested according to ISO 10297.
This document has been written for referencing in the UN Model Regulations [1].
In this document the unit bar is used, due to its universal use in the field of technical gases. It should,
however, be noted that bar is not an SI unit, and that the corresponding SI unit for pressure is Pa
5 5 2
(1 bar = 10 Pa = 10 N/m ).
Pressure values given in this document are given as gauge pressure (pressure exceeding atmospheric
pressure) unless noted otherwise.
© ISO 2021 – All rights reserved v
---------------------- Page: 7 ----------------------
oSIST prEN ISO 14246:2021
---------------------- Page: 8 ----------------------
oSIST prEN ISO 14246:2021
DRAFT INTERNATIONAL STANDARD ISO/DIS 14246:2021(E)
Gas cylinders — Cylinder valves — Manufacturing tests and
examinations
1 Scope
This document describes the procedures and acceptance criteria for manufacturing tests and
examinations (sometimes called initial inspection and tests) of valves designed and type tested
according to ISO 10297.
This documen
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.