SIST EN ISO 407:2023
(Main)Small medical gas cylinders - Pin-index yoke-type valve connections (ISO 407:2023)
Small medical gas cylinders - Pin-index yoke-type valve connections (ISO 407:2023)
This document is applicable to pin-index yoke-type valve connections for medical gas cylinders, with a working pressure up to a maximum of 200 bar or test pressure up to a maximum of 300 bar, or both.
NOTE 1 This type of connection is primarily used for small cylinders (5 l or below).
NOTE 2 In this document the unit bar is used, due to its universal use in the field of technical gases. It should, however, be noted that bar is not an SI unit, and that the corresponding SI unit for pressure is Pa (1 bar = 105 Pa = 105 N/m2).
This document specifies:
— basic dimensions;
— requirements for alternative designs of the yoke-type valve connections;
— dimensions and positions for the holes and pins for the outlet connections.
It also specifies the dimensions and positions for the holes and pins for the outlet connections for gases and gas mixtures.
Kleine Gasflaschen für die medizinische Anwendung - Ventilseitenstutzen mit Anschlussbügel nach dem PIN-Index-System (ISO 407:2023)
Dieses Dokument gilt für Bügelverschlüsse nach dem Pin-Index-System für Gasflaschen für die medizinische Anwendung mit einem maximalen Arbeitsdruck bis 200 bar oder einem maximalen Prüfdruck bis 300 bar oder beidem.
ANMERKUNG 1 Diese Verbindungsart wird hauptsächlich an kleinen Gasflaschen (5 l oder weniger) angewendet.
ANMERKUNG 2 In diesem Dokument wird die Einheit Bar verwendet, da sie im Bereich der technischen Gase universell einsetzbar ist. Es sollte jedoch beachtet werden, dass das Bar keine SI-Einheit ist und dass die entsprechende SI Einheit für den Druck Pa ist (1 bar = 105 Pa = 105 N/m2).
Dieses Dokument legt Folgendes fest:
Grundmaße;
Anforderungen an alternative Auslegungen von Bügelventilverschlüssen;
Maße und Anordnungen der Passlöcher und -stifte für die Anschlussverbindungen.
Es legt auch die Maße und Anordnungen der Passlöcher und -stifte für die Anschlussverbindungen für Gase und Gasgemische fest.
Petites bouteilles à gaz médicaux - Raccords de robinets du type étrier avec ergots de sécurité (ISO 407:2023)
Le présent document s’applique aux raccords de robinet du type étrier avec ergots de sécurité pour bouteilles à gaz médicaux d’une pression de service maximale de 200 bar et/ou d’une pression d’épreuve maximale de 300 bar.
NOTE 1 Ce type de raccord est essentiellement utilisé pour les petites bouteilles (de 5 l ou moins).
NOTE 2 Dans ce document, l’unité de pression utilisée est le bar, en raison de son usage universel dans le domaine des gaz techniques. Il convient cependant de noter que le bar n’est pas une unité du Système international, lequel utilise le Pascal (Pa) (1 bar = 105 Pa = 105 N/m2) pour la pression.
Le présent document spécifie:
— les dimensions de base des raccords;
— les exigences requises des variantes de construction des raccords de robinets du type étrier;
— les dimensions et positions des trous et des ergots des raccords de sortie.
Il spécifie également les dimensions et les positions des trous et des ergots des sorties de raccords pour les gaz et les mélanges de gaz.
Male plinske jeklenke za uporabo v medicini - Ventilski priključni nastavki po sistemu pin-index (ISO 407:2023)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 407:2023
01-september-2023
Male plinske jeklenke za uporabo v medicini - Ventilski priključni nastavki po
sistemu pin-index (ISO 407:2023)
Small medical gas cylinders - Pin-index yoke-type valve connections (ISO 407:2023)
Kleine Gasflaschen für die medizinische Anwendung - Ventilseitenstutzen mit
Anschlussbügel nach dem PIN-Index-System (ISO 407:2023)
Petites bouteilles à gaz médicaux - Raccords de robinets du type étrier avec ergots de
sécurité (ISO 407:2023)
Ta slovenski standard je istoveten z: EN ISO 407:2023
ICS:
11.040.10 Anestezijska, respiratorna in Anaesthetic, respiratory and
reanimacijska oprema reanimation equipment
23.020.35 Plinske jeklenke Gas cylinders
23.060.40 Tlačni regulatorji Pressure regulators
SIST EN ISO 407:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 407:2023
---------------------- Page: 2 ----------------------
SIST EN ISO 407:2023
EN ISO 407
EUROPEAN STANDARD
NORME EUROPÉENNE
August 2023
EUROPÄISCHE NORM
ICS 11.040.10 Supersedes EN ISO 407:2021
English Version
Small medical gas cylinders - Pin-index yoke-type valve
connections (ISO 407:2023)
Petites bouteilles à gaz médicaux - Raccords de Kleine Gasflaschen für die medizinische Anwendung -
robinets du type étrier avec ergots de sécurité (ISO Ventilseitenstutzen mit Anschlussbügel nach dem PIN-
407:2023) Index-System (ISO 407:2023)
This European Standard was approved by CEN on 1 July 2023.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 407:2023 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 407:2023
EN ISO 407:2023 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 407:2023
EN ISO 407:2023 (E)
European foreword
This document (EN ISO 407:2023) has been prepared by Technical Committee ISO/TC 58 "Gas
cylinders" in collaboration with Technical Committee CEN/TC 23 “Transportable gas cylinders” the
secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by February 2024, and conflicting national standards
shall be withdrawn at the latest by February 2024.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 407:2021.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 407:2023 has been approved by CEN as EN ISO 407:2023 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 407:2023
---------------------- Page: 6 ----------------------
SIST EN ISO 407:2023
INTERNATIONAL ISO
STANDARD 407
Fifth edition
2023-07
Small medical gas cylinders — Pin-
index yoke-type valve connections
Petites bouteilles à gaz médicaux — Raccords de robinets du type
étrier avec ergots de sécurité
Reference number
ISO 407:2023(E)
© ISO 2023
---------------------- Page: 7 ----------------------
SIST EN ISO 407:2023
ISO 407:2023(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
© ISO 2023 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 407:2023
ISO 407:2023(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Valve . 1
5 Yoke . 2
6 Basic dimensions . 2
6.1 General . 2
6.2 Pin-index yoke-type valve body . 3
6.3 Single-pin yoke-type valve connection system . 4
6.4 Two-pin yoke-type valve connection system with the pins in a single row . 4
6.5 Two-pin yoke-type valve connection system with the pins in a double row . 5
6.6 Basic dimensions . 5
7 Requirements for alternative designs of yoke-type valve connections .6
7.1 Requirements for the design of the connecting yoke . 6
7.2 Examples of alternative construction for the connecting yoke . 6
8 Dimensions and positions of the holes and pins for yoke-type valve connections .9
8.1 General . 9
8.2 Outlet connection with single-pin system . 9
8.3 Outlet connections with two-pin/single-row system . 10
8.3.1 Outlet connection for oxygen . 10
8.3.2 Outlet connection for oxygen/carbon dioxide mixture (CO ≤ 7 %) . 11
2
8.3.3 Outlet connection for oxygen/helium mixture (He ≤ 80 %) . 11
8.3.4 Outlet connection for ethylene .12
8.3.5 Outlet connection for nitrous oxide (with or without liquid draw-off) .12
8.3.6 Outlet connection for cyclopropane . 13
8.3.7 Outlet connection for helium and for helium/oxygen mixture (O < 20 %) .13
2
8.3.8 Outlet connection for carbon dioxide (with or without liquid draw-off) and
for carbon dioxide/oxygen mixture (CO > 7 %) . 14
2
8.3.9 Outlet connection for medical air . 14
8.3.10 Outlet connection for nitrogen . 15
8.4 Outlet connection with two-pin/double-row system . 15
iii
© ISO 2023 – All rights reserved
---------------------- Page: 9 ----------------------
SIST EN ISO 407:2023
ISO 407:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 58, Gas cylinders, Subcommittee SC 2,
Cylinders fittings, in collaboration with the European Committee for Standardization (CEN) Technical
Committee CEN/TC 23, Transportable gas cylinders, in accordance with the Agreement on technical
cooperation between ISO and CEN (Vienna Agreement).
This fifth edition cancels and replaces the fourth edition (ISO 407:2021) of which it constitutes a minor
revision.
The main changes are as follows:
— correction of Figure 1.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
© ISO 2023 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 407:2023
INTERNATIONAL STANDARD ISO 407:2023(E)
Small medical gas cylinders — Pin-index yoke-type valve
connections
1 Scope
This document is applicable to pin-index yoke-type valve connections for medical gas cylinders, with
a wor
...
SLOVENSKI STANDARD
oSIST prEN ISO 407:2023
01-maj-2023
Male plinske jeklenke za uporabo v medicini - Ventilski priključni nastavki po
sistemu pin-index (ISO/FDIS 407:2023)
Small medical gas cylinders - Pin-index yoke-type valve connections (ISO/FDIS
407:2023)
Kleine Gasflaschen für die medizinische Anwendung - Ventilseitenstutzen mit
Anschlussbügel nach dem PIN-Index-System (ISO/FDIS 407:2023)
Petites bouteilles à gaz médicaux - Raccords de robinets du type étrier avec ergots de
sécurité (ISO/FDIS 407:2023)
Ta slovenski standard je istoveten z: prEN ISO 407
ICS:
11.040.10 Anestezijska, respiratorna in Anaesthetic, respiratory and
reanimacijska oprema reanimation equipment
23.020.35 Plinske jeklenke Gas cylinders
23.060.40 Tlačni regulatorji Pressure regulators
oSIST prEN ISO 407:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 407:2023
---------------------- Page: 2 ----------------------
oSIST prEN ISO 407:2023
FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 407
ISO/TC 58/SC 2
Small medical gas cylinders — Pin-
Secretariat: AFNOR
index yoke-type valve connections
Voting begins on:
2023-03-08
Petites bouteilles à gaz médicaux — Raccords de robinets du type
étrier avec ergots de sécurité
Voting terminates on:
2023-05-31
ISO/CEN PARALLEL PROCESSING
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/FDIS 407:2023(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS. © ISO 2023
---------------------- Page: 3 ----------------------
oSIST prEN ISO 407:2023
ISO/FDIS 407:2023(E)
FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 407
ISO/TC 58/SC 2
Small medical gas cylinders — Pin-
Secretariat: AFNOR
index yoke-type valve connections
Voting begins on:
Petites bouteilles à gaz médicaux — Raccords de robinets du type
étrier avec ergots de sécurité
Voting terminates on:
COPYRIGHT PROTECTED DOCUMENT
© ISO 2023
ISO/CEN PARALLEL PROCESSING
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
RECIPIENTS OF THIS DRAFT ARE INVITED TO
ISO copyright office
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
CP 401 • Ch. de Blandonnet 8
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
CH-1214 Vernier, Geneva
DOCUMENTATION.
Phone: +41 22 749 01 11
IN ADDITION TO THEIR EVALUATION AS
Reference number
Email: copyright@iso.org
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO
ISO/FDIS 407:2023(E)
Website: www.iso.org
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
Published in Switzerland
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN
DARDS TO WHICH REFERENCE MAY BE MADE IN
ii
© ISO 2023 – All rights reserved
NATIONAL REGULATIONS. © ISO 2023
---------------------- Page: 4 ----------------------
oSIST prEN ISO 407:2023
ISO/FDIS 407:2023(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Valve . 1
5 Yoke . 2
6 Basic dimensions . 2
6.1 General . 2
6.2 Pin-index yoke-type valve body . 3
6.3 Single-pin yoke-type valve connection system . 4
6.4 Two-pin yoke-type valve connection system with the pins in a single row . 4
6.5 Two-pin yoke-type valve connection system with the pins in a double row . 5
6.6 Basic dimensions . 5
7 Requirements for alternative designs of yoke-type valve connections .6
7.1 Requirements for the design of the connecting yoke . 6
7.2 Examples of alternative construction for the connecting yoke . 6
8 Dimensions and positions of the holes and pins for yoke-type valve connections .9
8.1 General . 9
8.2 Outlet connection with single-pin system . 9
8.3 Outlet connections with two-pin/single-row system . 10
8.3.1 Outlet connection for oxygen . 10
8.3.2 Outlet connection for oxygen/carbon dioxide mixture (CO ≤ 7 %) . 11
2
8.3.3 Outlet connection for oxygen/helium mixture (He ≤ 80 %) . 11
8.3.4 Outlet connection for ethylene .12
8.3.5 Outlet connection for nitrous oxide (with or without liquid draw-off) .12
8.3.6 Outlet connection for cyclopropane . 13
8.3.7 Outlet connection for helium and for helium/oxygen mixture (O < 20 %) .13
2
8.3.8 Outlet connection for carbon dioxide (with or without liquid draw-off) and
for carbon dioxide/oxygen mixture (CO > 7 %) . 14
2
8.3.9 Outlet connection for medical air . 14
8.3.10 Outlet connection for nitrogen . 15
8.4 Outlet connection with two-pin/double-row system . 15
iii
© ISO 2023 – All rights reserved
---------------------- Page: 5 ----------------------
oSIST prEN ISO 407:2023
ISO/FDIS 407:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 58, Gas cylinders, Subcommittee SC 2,
Cylinders fittings, in collaboration with the European Committee for Standardization (CEN) Technical
Committee CEN/TC 23, Transportable gas cylinders, in accordance with the Agreement on technical
cooperation between ISO and CEN (Vienna Agreement).
This fifth edition cancels and replaces the fourth edition (ISO 407:2021) of which it constitutes a minor
revision.
The main changes are as follows:
— correction of Figure 1.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
© ISO 2023 – All rights reserved
---------------------- Page: 6 ----------------------
oSIST prEN ISO 407:2023
FINAL DRAFT INTERNATIONAL STANDARD ISO/FDIS 407:2023(E)
Small medical gas cylinders — Pin-index yoke-type valve
connections
1 Scope
This document is applicable to pin-index yoke-type valve connections for medical gas cylinders, with
a working pressure up to a maximum of 200 bar or test pressure up to a maximum of 300 bar, or both.
NOTE 1 This type of connection is primarily used for small cylinders (5 l or below).
NOTE 2 In this document the unit bar is used, due to its universal use in the field of technical gases. It should,
5
however, be noted that bar is not an SI unit, and that the corresponding SI unit for pressure is Pa (1 bar = 10 Pa =
5 2
10 N/m ).
This document specifies:
— basic dimensions;
— requirements for alternative designs of the yoke-type valve connections;
— dimensions and positions for the holes and pins for the outlet connections.
It also specifies the dimensions and positions for the holes and pins for the outlet connections for gases
and gas mixtures.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 32, Gas cylinders for medical use — Marking for identification of content
3 Terms and definitions
No terms and definitions are listed in this document.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
—
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.