SIST EN 1315:2010
(Main)Dimensional classification of round timber
Dimensional classification of round timber
This European Standard specifies a dimensional classification for round timber (softwood and hardwood) for which the intended use is not known.
Dimensions-Sortierung von Rundholz
Diese Europäische Norm legt die allgemeine Sortierung nach Maßen von Rundholz (Nadel- und Laubholz) fest, bei dem die beabsichtigte Verwendung nicht bekannt ist.
Classement dimensionnel des bois ronds
La présente norme européenne spécifie un classement dimensionnel pour les bois ronds (bois résineux et bois feuillus) pour lesquels on ne connaît pas l’utilisation finale.
Razvrščanje po izmerah za okrogli les
Ta evropski standard določa razvrščanje po izmerah za okrogli les (mehki in trdi les), katerega namen uporabe ni znan.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Dimensions-Sortierung von RundholzClassement dimensionnel des bois rondsDimensional classification of round timber79.040Les, hlodovina in žagan lesWood, sawlogs and sawn timberICS:Ta slovenski standard je istoveten z:EN 1315:2010SIST EN 1315:2010en,fr,de01-april-2010SIST EN 1315:2010SLOVENSKI
STANDARDSIST EN 1315-2:20001DGRPHãþD
SIST EN 1315:2010
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 1315
January 2010 ICS 79.040 Supersedes EN 1315-1:1997, EN 1315-2:1997English Version
Dimensional classification of round timber
Classement dimensionnel des bois ronds
Dimensions-Sortierung von Rundholz This European Standard was approved by CEN on 18 December 2009.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1315:2010: ESIST EN 1315:2010
EN 1315:2010 (E) 2 Contents Page Foreword .31 Scope .42 Normative references .43 Terms and definitions .44 Dimensional classification .4 SIST EN 1315:2010
EN 1315:2010 (E) 3 Foreword This document (EN 1315:2010) has been prepared by Technical Committee CEN/TC 175 “Round and sawn timber”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 2010, and conflicting national standards shall be withdrawn at the latest by July 2010. Attention is drawn to the possibility that some of the elements
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.