oSIST prEN ISO 636:2024
(Main)Welding consumables - Rods, wires and deposits for tungsten inert gas welding of non-alloy and fine-grain steels - Classification (ISO/DIS 636:2024)
Welding consumables - Rods, wires and deposits for tungsten inert gas welding of non-alloy and fine-grain steels - Classification (ISO/DIS 636:2024)
ISO 636:2017 specifies requirements for classification of rods and wires in the as-welded condition and in the post-weld heat-treated condition for tungsten inert gas welding of non-alloy and fine-grain steels with a minimum yield strength of up to 500 MPa or a minimum tensile strength of up to 570 MPa.
ISO 636:2017 is a combined specification providing classification utilizing a system based upon the yield strength and the average impact energy of 47 J of all-weld metal or utilizing a system based upon the tensile strength and the average impact energy of 27 J of all-weld metal.
a) Paragraphs and tables which carry the suffix letter "A" are applicable only to rods and wires classified to the system based upon the yield strength and the average impact energy of 47 J of all-weld metal in accordance with this document.
b) Paragraphs and tables which carry the suffix letter "B" are applicable only to rods and wires classified to the system based upon the tensile strength and the average impact energy of 27 J of all-weld metal in accordance with this document.
c) Paragraphs and tables which have neither the suffix letter "A" nor the suffix letter "B" are applicable to all rods and wires classified in accordance with this document.
Schweißzusätze - Stäbe, Drähte und Schweißgut zum Wolfram-Inertgasschweißen von unlegierten Stählen und Feinkornstählen - Einteilung (ISO/DIS 636:2024)
Dieses Dokument legt Anforderungen für die Einteilung von Stäben, Drähten und Schweißgut im Schweißzustand und nach einer Wärmebehandlung (PWHT, en: post-weld heat-treated) für das Wolfram Inertgasschweißen von unlegierten Stählen und Feinkornstählen mit einer Mindeststreckgrenze bis zu 500 MPa oder einer Mindestzugfestigkeit bis zu 570 MPa fest.
Dieses Dokument ist eine kombinierte Spezifikation, die zur Einteilung ein System nutzt, das auf der Streckgrenze und der durchschnittlichen Kerbschlagarbeit des reinen Schweißgutes von 47 J beruht, oder die ein System nutzt, das auf der Zugfestigkeit und der durchschnittlichen Kerbschlagarbeit des reinen Schweißgutes von 27 J beruht.
a) Bestandteile, die den Zusatz „System A“ tragen, sind nur für Stäbe, Drähte und Schweißgut anwendbar, die nach dem System eingeteilt sind, das auf der Streckgrenze und der durchschnittlichen Kerbschlagarbeit des reinen Schweißgutes von 47 J nach diesem Dokument beruht.
b) Bestandteile, die den Zusatz „System B“ tragen, sind nur für Stäbe, Drähte und Schweißgut anwendbar, die nach dem System eingeteilt sind, das auf der Zugfestigkeit und der durchschnittlichen Kerbschlagarbeit des reinen Schweißgutes von 27 J nach diesem Dokument beruht.
c) Bestandteile, die weder „System A“ noch „System B“ als Zusatz tragen, sind für alle nach diesem Dokument eingeteilten Stäbe, Drähte und Schweißgut anwendbar.
Produits consommables pour le soudage - Baguettes, fils et dépôts pour soudage TIG des aciers non alliés et des aciers à grains fins - Classification (ISO/DIS 636:2024)
ISO 636:2017 spécifie les exigences relatives à la classification des baguettes et des fils à l'état brut de soudage et à l'état traité thermiquement après soudage, en soudage TIG (soudage à l'arc sous protection de gaz inerte avec électrode de tungstène) des aciers non alliés et des aciers à grains fins ayant une limite d'élasticité minimale pouvant atteindre 500 MPa ou une résistance à la traction minimale pouvant atteindre 570 MPa.
ISO 636:2017 propose une spécification mixte permettant une classification utilisant un système fondé soit sur la limite d'élasticité et l'énergie de rupture moyenne de 47 J pour le métal fondu hors dilution, soit sur la résistance à la traction et l'énergie de rupture moyenne de 27 J pour le métal fondu hors dilution.
a) Les paragraphes et les tableaux qui portent le suffixe «A» ne sont applicables qu'aux baguettes et fils classifiés d'après le système basé sur la limite d'élasticité et l'énergie de rupture moyenne de 47 J pour le métal fondu hors dilution conformément au présent document.
b) Les paragraphes et les tableaux qui portent le suffixe «B» ne sont applicables qu'aux baguettes et fils classifiés d'après le système basé sur la résistance à la traction et l'énergie de rupture moyenne de 27 J pour le métal fondu hors dilution conformément au présent document.
c) Les paragraphes et les tableaux ne comportant ni le suffixe «A» ni le suffixe «B» sont applicables à toutes les baguettes et à tous les fils classifiés conformément au présent document.
Dodajni in pomožni materiali za varjenje - Palice, žice in čisti vari pri varjenju nelegiranih in drobnozrnatih jekel po postopku TIG - Razvrstitev (ISO/DIS 636:2024)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-april-2024
Dodajni in pomožni materiali za varjenje - Palice, žice in čisti vari pri varjenju
nelegiranih in drobnozrnatih jekel po postopku TIG - Razvrstitev (ISO/DIS
636:2024)
Welding consumables - Rods, wires and deposits for tungsten inert gas welding of non-
alloy and fine-grain steels - Classification (ISO/DIS 636:2024)
Schweißzusätze - Stäbe, Drähte und Schweißgut zum Wolfram-Inertgasschweißen von
unlegierten Stählen und Feinkornstählen - Einteilung (ISO/DIS 636:2024)
Produits consommables pour le soudage - Baguettes, fils et dépôts pour soudage TIG
des aciers non alliés et des aciers à grains fins - Classification (ISO/DIS 636:2024)
Ta slovenski standard je istoveten z: prEN ISO 636
ICS:
25.160.20 Potrošni material pri varjenju Welding consumables
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT
International
Standard
ISO/DIS 636
ISO/TC 44/SC 3
Welding consumables — Rods,
Secretariat: ANSI
wires and deposits for tungsten
Voting begins on:
inert gas welding of non-alloy and
2024-02-19
fine-grain steels — Classification
Voting terminates on:
2024-05-13
Produits consommables pour le soudage — Baguettes et fils pour
dépôts par soudage TIG des aciers non alliés et des aciers à grains
fins — Classification
ICS: 25.160.20
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Reference number
ISO/DIS 636:2024(en)
DRAFT
ISO/DIS 636:2024(en)
International
Standard
ISO/DIS 636
ISO/TC 44/SC 3
Welding consumables — Rods,
Secretariat: ANSI
wires and deposits for tungsten
Voting begins on:
inert gas welding of non-alloy and
fine-grain steels — Classification
Voting terminates on:
Produits consommables pour le soudage — Baguettes et fils pour
dépôts par soudage TIG des aciers non alliés et des aciers à grains
fins — Classification
ICS: 25.160.20
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
© ISO 2024
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
BE CONSIDERED IN THE LIGHT OF THEIR
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
or ISO’s member body in the country of the requester.
NATIONAL REGULATIONS.
ISO copyright office
RECIPIENTS OF THIS DRAFT ARE INVITED
CP 401 • Ch. de Blandonnet 8
TO SUBMIT, WITH THEIR COMMENTS,
CH-1214 Vernier, Geneva
NOTIFICATION OF ANY RELEVANT PATENT
Phone: +41 22 749 01 11
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland Reference number
ISO/DIS 636:2023(en)
ii
ISO/DIS 636:2023(en)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Classification . 2
4.1 General .2
4.1.1 Classification systems .2
5 Symbols and requirements . 2
5.1 Symbol for the product/process .2
5.2 Symbol for strength and elongation of all-weld metal .2
5.3 Symbol for impact properties of all-weld metal .3
5.3.1 A - Classification by yield strength and 47 J impact energy .3
5.3.2 B - Classification by tensile strength and 27 J impact energy .3
5.4 Symbol for the chemical composition of rods or wires .4
6 Mechanical tests . 8
6.1 Preheating and interpass temperatures .8
6.2 Welding conditions and pass sequence .8
6.3 PWHT condition .9
7 Chemical analysis . . 9
8 Rounding procedure . 9
9 Retesting . 9
10 Technical delivery conditions . 10
11 Designation examples . 10
11.1 Example 1 – Classification by yield strength and 47 J impact energy – A .10
11.2 Example 2 – Classification by tensile strength and 27 J impact energy – B .10
11.3 Example 3 - Classification by yield strength and 47 J impact energy – A .11
11.4 Example 4 - Classification by tensile strength and 27 J impact energy – B .11
11.5 Example 4 - Classification by tensile strength and 27 J impact energy – B . 12
Bibliography .13
iii
ISO/DIS 636:2023(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 44, Welding and allied processes, Subcommittee
SC 3, Welding consumables, in collaboration with the European Committee for Standardization (CEN)
Technical Committee CEN/TC 121, Welding and allied processes, in accordance with the Agreement on
technical cooperation between ISO and CEN (Vienna Agreement).
This sixth edition cancels and replaces the fifth edition (ISO 636:2017), which has been technically revised.
The main changes are as follows:
— to be added after DIS ballot
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
Official interpretations of ISO/TC 44 documents, where they exist, are available from this page:
https://committee.iso.org/sites/tc44/home/interpretation.html.
iv
ISO/DIS 636:2023(en)
Introduction
This document provides a classification for the designation of rods and wires in terms of their chemical
composition and, where required, in terms of the yield strength, tensile strength, and elongation of the all-
weld metal. The ratio of yield to tensile strength of weld metal is generally higher than that of parent metal.
Matching weld metal yield strength to parent metal yield strength will not necessarily ensure that the weld
metal tensile strength matches that of the parent material.
Where the application requires matching tensile strengths, selection of consumables is made by reference to
columns 3 and 7 of Table 2.
Of note is that the mechanical properties of all-weld metal test specimens used to classify the rods and wires
vary from those obtained in production joints because of differences in welding procedure such as diameter,
width of weave, welding position, and material composition.
[1]
The classification according to system A is mainly based on EN 1668:1997. The classification according to
system B is mainly based upon standards used around the Pacific Rim.
v
DRAFT International Standard ISO/DIS 636:2023(en)
Welding consumabl
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.