SIST EN 12697-33:2004
(Main)Bituminous mixtures - Test methods for hot mix asphalt - Part 33: Specimen prepared by roller compactor
Bituminous mixtures - Test methods for hot mix asphalt - Part 33: Specimen prepared by roller compactor
This European Standard specifies the methods for compacting parallelepipedic specimens (slabs) of bituminous mixtures, to be used directly for subsequent testing, or from which test specimens are cut. For a given mass of bituminous mixture, the specimens can be prepared either under controlled compaction energy, or until a specified volume and therefore bulk density are obtained. This standard is applicable to bituminous mixtures manufactured in the laboratory or in a mixing plant.
Asphalt - Prüfverfahren für Heißasphalt - Teil 33: Probestückvorbereitung mit einem Walzenverdichtungsgerät
Diese Europäische Norm legt die Verfahren fest für die Verdichtung von planparallelen Probekörpern (Platten) aus Asphalt, die für nachfolgende Prüfungen direkt verwendet oder aus denen Prüfkörper geschnitten werden können. Von einer vorgegebenen Asphaltmasse können Probekörper entweder mit einer gesteuerten Verdichtungsenergie oder mit einem bestimmten Volumen und infolgedessen einer bestimmten Raumdichte hergestellt werden.
Mélange bitumineux - Méthodes d'essai pour mélange hydrocarboné a chaud - Partie 33: Confection d'éprouvettes au compacteur de plaque
La présente norme européenne définit les méthodes de compactage des éprouvettes parallélépipédiques (plaques) de mélanges bitumineux, qui doivent etre utilisées directement ou pour des essais ultérieurs ou a partir desquelles des éprouvettes sont prélevées. Pour une masse donnée de mélange bitumineux, les éprouvettes peuvent etre préparées soit a une énergie de compactage contrôlée, soit a volume spécifié, et par conséquent a masse volumique apparente spécifiée. La présente norme s'applique aux mélanges bitumineux fabriqués en laboratoire ou dans une centrale d'enrobage.
Bitumenske zmesi – Preskusne metode za vroče asfaltne zmesi – 33. del: Preskušanci, pripravljeni z valjastim zgoščevalnikom
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Bituminous mixtures - Test methods for hot mix asphalt - Part 33: Specimen prepared by roller compactorMélange bitumineux - Méthodes d'essai pour mélange hydrocarboné a chaud - Partie 33: Confection d'éprouvettes au compacteur de plaqueAsphalt - Prüfverfahren für Heißasphalt - Teil 33: Probestückvorbereitung mit einem WalzenverdichtungsgerätTa slovenski standard je istoveten z:EN 12697-33:2003SIST EN 12697-33:2004en93.080.20Materiali za gradnjo cestRoad construction materialsICS:SLOVENSKI
STANDARDSIST EN 12697-33:200401-junij-2004
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 12697-33December 2003ICS 93.080.20English versionBituminous mixtures - Test methods for hot mix asphalt - Part33: Specimen prepared by roller compactorMélange bitumineux - Méthodes d'essai pour mélangehydrocarboné à chaud - Partie 33: Confection d'éprouvettesau compacteur de plaqueAsphalt - Prüfverfahren für Heißasphalt - Teil 33:Probestückvorbereitung mit einemWalzenverdichtungsgerätThis European Standard was approved by CEN on 3 November 2003.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and UnitedKingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2003 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 12697-33:2003 E
EN 12697-33:2003 (E)2ContentsPageForeword.31Scope.62Normative references.63Terms, definitions, symbols and abbreviations.63.1Terms and definitions.63.2Symbols and abbreviations.74Principle.85Apparatus.85.1Method using a wheel or two wheels fitted with pneumatic tyres.85.2Methods using a smooth steel roller.95.2.1Smooth steel roller.95.2.2Steel roller used on wheel fitted with pneumatic tyres.105.3Method using a roller running on vertical sliding steel plates.106Preparation.116.1Mass of bituminous mixture.116.2Filling the mould.117Compaction procedure.127.1Method using wheels fitted with pneumatic tyres.127.1.1Test conditions.127.1.2Compaction.127.2Methods using a smooth steel roller.137.2.1General.137.2.2Compaction by a specified energy.137.2.3Compaction with controlled compaction energy.137.2.4Compaction to obtain a specified voids content or compaction degree.147.3Method using a roller running on vertical sliding steel plates.147.4Removing the mould.148Test report.14
EN 12697-33:2003 (E)3ForewordThis document (EN 12697-33) has been prepared by Technical Committee CEN/TC 227 “Road materials”, thesecretariat of which is held by DIN.This European Standard shall be given the status of a national standard, either by publication of an identicaltext or by endorsement, at the latest by June 2004, and conflicting national standards shall be withdrawn atthe latest by August 2005.This European Standard forms a part of a series of tests for mechanical and physical properties of bituminousmixtures as listed below.EN 12697-1, Bituminous mixtures — Test methods for hot mix asphalt — Part 1: Soluble binder content.EN 12697-2, Bituminous mixtures — Test methods for hot mix asphalt — Part 2: Determination of particle sizedistribution.EN 12697-3, Bituminous mixtures — Test methods for hot mix asphalt — Part 3: Bitumen recovery: Rotaryevaporator.EN 12697-4, Bituminous mixtures — Test methods for hot mix asphalt — Part 4: Bitumen recovery:Fractionating column.EN 12697-5, Bituminous mixtures — Test methods for hot mix asphalt — Part 5: Determination of themaximum density.EN 12697-6, Bituminous mixtures — Test methods for hot mix asphalt — Part 6: Determination of bulk densityof bituminous specimensEN 12697-7, Bituminous mixtures — Test methods for hot mix asphalt — Part 7: Determination of bulk densityof bituminous specimens by gamma rays.EN 12697-8, Bituminous mixtures — Test methods for hot mix asphalt — Part 8: Determination of the voidcharacteristics of bituminous specimens.EN 12697-9, Bituminous mixtures — Test methods for hot mix asphalt — Part 9: Determination of thereference densityEN 12697-10, Bituminous mixtures — Test methods for hot mix asphalt — Part 10: Compactibility.EN 12697-11, Bituminous mixtures — Test methods for hot mix asphalt — Part 11: Determination of theaffinity between aggregate and bitumen.EN 12697-12, Bituminous mixtures — Test methods for hot mix asphalt — Part 12: Determination of the watersensitivity of bituminous specimens.EN 12697-13, Bituminous mixtures — Test methods for hot mix asphalt — Part 13: Temperaturemeasurement.EN 12697-14, Bituminous mixture — Test methods for hot mix asphalt — Part 14: Water content.EN 12697-15, Bituminous mixtures — Test methods for hot mix asphalt — Part 15: Determination of thesegregation sensitivity
EN 12697-33:2003 (E)4prEN 12697-16, Bituminous mixtures — Test methods for hot mix asphalt — Part 16: Abrasion by studdedtyres.prEN 12697-17, Bituminous mixture — Test methods for hot mix asphalt — Part 17: Partial loss of porousasphalt specimen.prEN 12697-18, Bituminous mixtures — Test methods for hot mix asphalt — Part 18: Binder drainage fromporous asphalt.prEN 12697-19, Bituminous mixtures — Test methods for hot mix asphalt — Part 19: Permeability ofspecimen.EN 12697-20, Bituminous mixtures — Test methods for hot mix asphalt — Part 20: Indentation using cube orMarshall specimen.prEN 12697-21, Bituminous mixtures — Test methods for hot mix asphalt — Part 21: Indentation using platespecimens.prEN 12697-22, Bituminous mixtures — Test methods for hot mix asphalt — Part 22: Wheel tracking.EN 12697-23, Bituminous mixtures — Test methods for hot mix asphalt — Part 23: Determination of theindirect tensile strength of bituminous specimens.prEN 12697-24, Bituminous mixtures — Test methods for hot mix asphalt — Part 24: Resistance to fatigue.prEN 12697-25, Bituminous mixtures — Test methods for hot mix asphalt — Part 25:
Cyclic compressiontest.prEN 12697-26, Bituminous mixtures — Test methods for hot mix asphalt — Part 26: Stiffness.EN 12697-27, Bituminous mixtures — Test methods for hot mix asphalt —Part 27: Sampling.EN 12697-28, Bituminous mixtures — Test methods for hot mix asphalt — Part 28: Preparation of samples fordetermining binder content, water content and grading.EN 12697-29, Bituminous mixtures — Test methods for hot mix asphalt — Part 29: Determination of thedimensions of a bituminous specimen.prEN 12697-30, Bituminous mixtures — Test methods for hot mix asphalt — Part 30: Specimen preparation,impact compactor.prEN 12697-31, Bituminous mixtures — Test methods for hot mix asphalt — Part 31: Specimen preparation,gyratory compactor.EN 12697-32, Bituminous mixtures — Test methods for hot mix asphalt — Part 32: Laboratory compaction ofbituminous mixtures by vibratory compactor.EN 12697-33, Bituminous mixtures — Test methods for hot mix asphalt — Part 33: Specimen prepared byroller compactor.prEN 12697-34, Bituminous mixtures — Test methods for hot mix asphalt — Part 34: Marshall test.prEN 12697-35, Bituminous mixtures — Test methods for hot mix asphalt — Part 35: Laboratory mixing.EN 12697-36, Bituminous mixtures — Test methods for hot mix asphalt — Part 36: Determination of thethickness of a bituminous pavement.
EN 12697-33:2003 (E)5EN 12697-37, Bituminous mixtures — Test methods for hot mix asphalt — Part 37: Hot sand test for theadhesivity of binder on pre-coated chippings for HRA.prEN 12697-38, Bituminous mixtures — Test methods for hot mix asphalt — Part 38: Test equipment andcalibration.prEN 12697-39, Bituminous mixtures — Test methods for hot mix asphalt — Part 39: Binder content byignition.prEN 12697-41, Bituminous mixtures — Test methods for hot mix asphalt — Part 41: Resistance to de-icingfluids.prEN 12697-42, Bituminous mixtures — Test methods for hot mix asphalt — Part 42: Amount of foreign matterin reclaimed asphalt.prEN 12697-43, Bituminous mixtures — Test methods for hot mix asphalt — Part 43: Resistance to fuel.prEN 12697-45, Bituminous mixtures — Test methods for hot mix asphalt — Part 45: Binder drainage –Schellenberg methodThe applicability of this European Standard is described in the product standards for bituminous mixtures(series of prEN 13108).No existing European Standard is superseded.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the followingcountries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark,Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands,Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and the United Kingdom.
EN 12697-33:2003 (E)61 ScopeThis European Standard specifies the methods for compacting parallelepipedal specimens (slabs) ofbituminous mixtures, to be used directly for subsequent testing, or from which test specimens are cut.For a given mass of bituminous mixture, the specimens are prepared either under controlled compactionenergy, or until a specified volume and therefore void content is obtained.This European Standard describes the following methods of compaction:¾ pneumatic tyre method,¾ steel roller method,¾ sliding plates method.This European Standard is applicable to bituminous mixtures manufactured in the laboratory or in a mixingplant.2 Normative referencesThis European Standard incorporates by dated or undated reference, provisions from other publications.These normative references are cited at the appropriate places in the text and the publications are listedhereafter. For dated references, subsequent amendments to or revisions of any of these publications apply tothis European Standard only when incorporated in it by amendment or revision. For undated references thelatest edition of the publication referred to applies (including amendments).EN 12697-27, Bituminous mixtures — Test methods for hot mix asphalt — Part 27: Sampling.prEN 12697-35, Bituminous mixtures — Test methods for hot mix asphalt — Part 35: Laboratory mixing.3 Terms, definitions, symbols and abbreviations3.1 Terms and definitionsFor the purposes of this European Standard, the following terms and definitions apply.3.1.1passone forward or one backward motion of the rolling load3.1.2slab axisaxis of symmetry of slab parallel to the largest dimension of the mould3.1.3lateral axisaxis of a pass parallel to largest dimension of a mould; situated at distance a from the slab axis (see Figure 1)3.1.4lateral translationdistance a between the slab axis and the lateral axis
EN 12697-33:2003 (E)7Key1Axis2Lateral axis3Left side4Right side5Central position6Rear position7Front position8Longitudinal translation of wheelsFigure 1 — Sketch plan of a slab, front face of equipment3.1.5rear positionlateral axis furthest from the front face of the equipment3.1.6central positionslab axis3.1.7front positionlateral axis nearest to the front face of the equipment3.1.8blocked axis modeequipment operating mode in which the height of the wheel shaft stays constant in relation to the upper edgeof mould during a pass3.1.9freed axis modeequipment operation mode in which the load applied into the slab remains constant during a pass3.1.10sweep planset of modes by which the wheel(s) pass(es) over the slab;
including order of execution, and extent of lateraltranslation3.2 Symbols and abbreviationsLis the interior length of mould, in millimetres (mm);lis the interior
width of mould, in millimetres (mm);his the interior height of mould, in millimetres (mm);
EN 12697-33:2003 (E)8Mis the mass of slab, in kilograms (kg);rmis the maximum density of bituminous mixture, in kilograms per cubic metre (kg/m3);nis the voids content in slab, in percent (%);Fis the load applied onto wheels or roller, in kilonewton (kN);bis the width of the roller, in millimetres (mm);Dis the diameter of the wheel(s) or roller, in millimetres (mm);Vtis the velocity of longitudinal translation of wheel(s), in millimetres per sec
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.