SIST EN 60811-501:2012
Electric and optical fibre cables - Test methods for non-metallic materials - Part 501: Mechanical tests - Tests for determining the mechanical properties of insulating and sheathing compounds
Electric and optical fibre cables - Test methods for non-metallic materials - Part 501: Mechanical tests - Tests for determining the mechanical properties of insulating and sheathing compounds
This Part 501 of IEC 60811 gives the procedure for determining the mechanical properties, which typically applies to cross-linked and thermoplastic compounds used for insulating and sheathing materials.
Kabel, isolierte Leitungen und Glasfaserkabel - Prüfverfahren für nichtmetallene Werkstoffe - Teil 501: Mechanische Prüfungen - Prüfungen zur Bestimmung der mechanischen Eigenschaften von Isolier- und Mantelwerkstoffen
Câbles électriques et câbles à fibres optiques - Méthodes d'essai pour les matériaux non-métalliques - Partie 501: Essais mécaniques - Essais pour déterminer les propriétés mécaniques des mélanges pour enveloppes isolantes et gaines
La CEI 60811-501:2012 décrit les méthodes pour la détermination des propriétés mécaniques, généralement applicables aux mélanges réticulés et thermoplastiques utilisés dans les matériaux d'isolation et de gainage. La CEI 60811-501:2012 annule et remplace l'Article 9 de la CEI 60811-1-1:1993, qui est supprimée. L'ensemble des informations relatives aux remplacements figure dans l'Annexe A de la CEI 60811-100:2012. Cette édition inclut la modification technique majeure suivante par rapport à l'édition précédente: les exigences relatives à l'épaisseur (minimale) des éprouvettes en forme d'haltère ont été modifiées. Voir également l'avant-propos de la CEI 60811-100. Cette publication doit être lue conjointement avec la CEI 60811-100:2012.
Električni in optični kabli - Preskuševalne metode za nekovinske materiale - 501. del: Mehanski preskusi - Preskusi za ugotavljanje mehanskih lastnosti zmesi za izolacije in oplaščenja
501. del standarda IEC 60811 navaja postopek za določanje mehanskih lastnosti, ki se običajno uporablja za zamrežene in termoplastične zmesi za izolacije in plašče.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 60811-501:2012
01-september-2012
(OHNWULþQLLQRSWLþQLNDEOL3UHVNXãHYDOQHPHWRGH]DQHNRYLQVNHPDWHULDOH
GHO 0HKDQVNLSUHVNXVL3UHVNXVL]DXJRWDYOMDQMHPHKDQVNLKODVWQRVWL]PHVL]D
L]RODFLMHLQRSODãþHQMD
Electric and optical fibre cables - Test methods for non-metallic materials - Part 501:
Mechanical tests - Tests for determining the mechanical properties of insulating and
sheathing compounds
Kabel, isolierte Leitungen und Glasfaserkabel - Prüfverfahren für nichtmetallene
Werkstoffe - Teil 501: Mechanische Prüfungen - Prüfungen zur Bestimmung der
mechanischen Eigenschaften von Isolier- und Mantelwerkstoffen
Câbles électriques et câbles à fibres optiques - Méthodes d'essai pour les matériaux non
-métalliques - Partie 501: Essais mécaniques - Essais pour déterminer les propriétés
mécaniques des mélanges pour enveloppes isolantes et gaines
Ta slovenski standard je istoveten z: EN 60811-501:2012
ICS:
29.035.01 Izolacijski materiali na Insulating materials in
splošno general
29.060.20 Kabli Cables
SIST EN 60811-501:2012 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 60811-501:2012
---------------------- Page: 2 ----------------------
SIST EN 60811-501:2012
EUROPEAN STANDARD
EN 60811-501
NORME EUROPÉENNE
June 2012
EUROPÄISCHE NORM
ICS 29.035.01; 29.060.20 Supersedes EN 60811-1-1:1995 (partially) + A1:2001 (partially)
English version
Electric and optical fibre cables -
Test methods for non-metallic materials -
Part 501: Mechanical tests -
Tests for determining the mechanical properties of insulating
and sheathing compounds
(IEC 60811-501:2012)
Câbles électriques et à fibres optiques - Kabel, isolierte Leitungen und
Méthodes d'essai pour les matériaux Glasfaserkabel - Prüfverfahren
non-métalliques - für nichtmetallene Werkstoffe -
Partie 501: Essais mécaniques - Teil 501: Mechanische Prüfungen -
Détermination des propriétés mécaniques Prüfungen zur Bestimmung
des mélanges pour les enveloppes der mechanischen Eigenschaften
isolantes et les gaines von Isolier- und Mantelwerkstoffen
(CEI 60811-501:2012) (IEC 60811-501:2012)
This European Standard was approved by CENELEC on 2012-04-17. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland, Turkey and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Management Centre: Avenue Marnix 17, B - 1000 Brussels
© 2012 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60811-501:2012 E
---------------------- Page: 3 ----------------------
SIST EN 60811-501:2012
EN 60811-501:2012 - 2 -
Foreword
The text of document 20/1297/FDIS, future edition 1 of IEC 60811-501, prepared by IEC/TC 20
"Electric cables" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
EN 60811-501:2012.
The following dates are fixed:
(dop) 2013-01-17
• latest date by which the document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2015-04-17
• latest date by which the national
standards conflicting with the
document have to be withdrawn
This document supersedes Clause 9 of EN 60811-1-1:1995 + A1:2001 (partially). Full details of the
replacements are shown in Annex A of EN 60811-100:2012.
EN 60811-501:2012 includes the following significant technical change with respect to
EN 60811-1-1:1995:
- the requirements for the (minimum) thickness of dumb-bell test pieces have changed.
See also the Foreword to EN 60811-100.
This standard is to be read in conjunction with EN 60811-100.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
This standard covers the Principle Elements of the Safety Objectives for Electrical Equipment
Designed for Use within Certain Voltage Limits (LVD - 2006/95/EC).
Endorsement notice
The text of the International Standard IEC 60811-501:2012 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated :
IEC 60811-1-1:1993 NOTE Harmonized as EN 60811-1-1:1995 (not modified).
---------------------- Page: 4 ----------------------
SIST EN 60811-501:2012
- 3 - EN 60811-501:2012
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year
IEC 60811-100 2012 Electric and optical fibre cables - Test EN 60811-100 2012
methods for non-metallic materials -
Part 100: General
IEC 60811-201 - Electric and optical fibre cables - Test EN 60811-201 -
methods for non-metallic materials -
Part 201: General tests - Measurement of
insulation thickness
IEC 60811-202 - Electric and optical fibre cables - Test EN 60811-202 -
methods for non-metallic materials -
Part 202: General tests - Measurement of
thickness of non-metallic sheath
IEC 60811-203 - Electric and optical fibre cables - Test EN 60811-203 -
methods for non-metallic materials -
Part 203: General tests - Measurement of
overall dimensions
IEC 60811-401 - Electric and optical fibre cables - Test EN 60811-401 -
methods for non-metallic materials -
Part 401: Miscellaneous tests - Thermal
ageing methods - Ageing in an air oven
IEC 60811-404 - Electric and optical fibre cables - Test EN 60811-404 -
methods for non-metallic materials -
Part 404: Miscellaneous tests - Mineral oil
immersion tests for sheaths
IEC 60811-606 - Electric and optical fibre cables - Test EN 60811-606 -
methods for non-metallic materials -
Part 606: Physical tests - Methods for
determining the density
---------------------- Page: 5 ----------------------
SIST EN 60811-501:2012
---------------------- Page: 6 ----------------------
SIST EN 60811-501:2012
IEC 60811-501
®
Edition 1.0 2012-03
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Electric and optical fibre cables – Test methods for non-metallic materials –
Part 501: Mechanical tests – Tests for determining the mechanical properties
of insulating and sheathing compounds
Câbles électriques et à fibres optiques – Méthodes d’essai pour les matériaux
non-métalliques –
Partie 501: Essais mécaniques – Détermination des propriétés mécaniques
des mélanges pour les enveloppes isolantes et les gaines
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX Q
ICS 29.035.01; 29.060.20 ISBN 978-2-88912-975-1
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 7 ----------------------
SIST EN 60811-501:2012
– 2 – 60811-501 IEC:2012
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Test method . 7
4.1 General . 7
4.2 Insulation . 7
4.2.1 General . 7
4.2.2 Sampling . 7
4.2.3 Preparation and conditioning of test pieces . 7
4.2.4 Determination of cross-sectional area . 9
4.2.5 Ageing treatment . 11
4.2.6 Tensile testing procedure . 11
4.2.7 Expression of results . 11
4.3 Sheath . 12
4.3.1 General . 12
4.3.2 Sampling . 12
4.3.3 Preparation and conditioning of test pieces . 12
4.3.4 Determination of cross-sectional area . 12
4.3.5 Ageing treatment . 13
4.3.6 Tensile testing procedure . 13
4.3.7 Expression of results . 13
5 Test report. 13
Annex A (informative) Principle of operation of a typical machine for preparing test
pieces . 16
Bibliography . 17
Figure 1 – Dumb-bell test piece . 14
Figure 2 – Small dumb-bell test piece . 14
Figure 3 – Punch end showing groove . 14
Figure 4 – Test pieces cut by grooved punch . 15
Figure A.1 – Machine for preparing test pieces . 16
---------------------- Page: 8 ----------------------
SIST EN 60811-501:2012
60811-501 IEC:2012 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
ELECTRIC AND OPTICAL FIBRE CABLES –
TEST METHODS FOR NON-METALLIC MATERIALS –
Part 501: Mechanical tests –
Tests for determining the mechanical properties
of insulating and sheathing compounds
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60811-501 has been prepared by IEC technical committee 20:
Electric cables.
This Part 501 of IEC 60811 cancels and replaces Clause 9 of IEC 60811-1-1:1993, which is
withdrawn. Full details of the replacements are shown in Annex A of IEC 60811-100:2012.
There is one significant technical change with respect to the previous edition:
– the requirements for the (minimum) thickness of dumb-bell test pieces have changed.
See also the Foreword to IEC 60811-100.
---------------------- Page: 9 ----------------------
SIST EN 60811-501:2012
– 4 – 60811-501 IEC:2012
The text of this standard is based on the following documents:
FDIS Report on voting
20/1297/FDIS 20/1346/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
This part of IEC 60811 shall be used in conjunction with IEC 60811-100.
A list of all the parts in the IEC 60811 series, published under the general title Electric and
optical fibre cables – Test methods for non-metallic materials, can be found on the IEC
website.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
---------------------- Page: 10 ----------------------
SIST EN 60811-501:2012
60811-501 IEC:2012 – 5 –
INTRODUCTION
The IEC 60811 series specifies the test methods to be used for testing non-metallic materials
of all types of cables. These test methods are intended to be referenced in standards for
cable construction and for cable materials.
NOTE 1 Non-metallic materials are typically used for insulating, sheathing, bedding, filling or taping within cables.
NOTE 2 These test methods are accepted as basic and fundamental and have been developed and used over
many years principally for the materials in all energy cables. They have also been widely accepted and used for
other cables, in particular optical fibre cables, communication and control cables and cables for ships and offshore
applications.
---------------------- Page: 11 ----------------------
SIST EN 60811-501:2012
– 6 – 60811-501 IEC:2012
ELECTRIC AND OPTICAL FIBRE CABLES –
TEST METHODS FOR NON-METALLIC MATERIALS –
Part 501: Mechanical tests –
Tests for determining the mechanical properties
of insulating and sheathing compounds
1 Scope
This Part 501 of IEC 60811 gives the procedure for determining the mechanical properties,
which typically applies to cross-linked and thermoplastic compounds used for insulating and
sheathing materials.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and
are indispensable for its application. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any
amendments) applies.
IEC 60811-100:2012, Electric and optical fibre cables – Test methods for non-metallic
materials – Part 100: General
IEC 60811-201, Electric and optical fibre cables – Test methods for non-metallic materials –
Part 201: General tests – Measurement of insulation thickness
IEC 60811-202, Electric and optical fibre cables – Test methods for non-metallic materials –
Part 202: General tests – Measurement of thickness of non-metallic sheaths
IEC 60811-203, Electric and optical fibre cables – Test methods for non-metallic materials –
Part 203: General tests – Measurement of overall dimensions
IEC 60811-401, Electric and optical fibre cables – Test methods for non-metallic materials –
Part 401: Miscellaneous tests – Thermal ageing methods – Ageing in an air oven
IEC 60811-404, Electric and optical fibre cables – Test methods for non-metallic materials –
Part 404: Miscellaneous tests – Mineral oil immersion tests for sheaths made with cross-
linked compounds
IEC 60811-606, Electric and optical fibre cables – Test methods for non-metallic materials –
Part 606: Physical tests – Methods for determining the density
3 Terms and de
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.