SIST EN 1846-3:2003+A1:2009

Firefighting and rescue service vehicles - Part 3: Permanently installed equipment - Safety and performance

1.1   This Part of this European Standard specifies the minimum requirements for safety and performance of some optional specific permanently installed equipment on firefighting and rescue service vehicles, operated by trained persons, as designated in EN 1846-1 and specified in EN 1846-2.
   NOTE 1   Categories and mass classes of the firefighting and rescue service vehicles are given in EN 1846-1.
   The permanently installed equipment dealt with in this Part of this European Standard is given below:
-   water installation;
-   additive installation;
-   monitor;
-   equipment gantries.
   NOTE 2   This Part of this European Standard should be read in conjunction with any national regulations in force for vehicles using the public roads and with any EU Directives and associated EFTA regulations in force relevant to vehicles and their equipment.
   For the purposes of this European Standard, the normal ambient temperature range is - 15 °C to + 35 °C.
   NOTE 3   In the case of utilization outside this temperature range, the particular temperature range should be specified by the user.
1.2   This Part of this European Standard is not applicable to:
-   personnel carrying vehicles;
-   vehicles with a gross laden mass not exceeding 2 t;
-   boats;
-   aircrafts;
-   trains;
-   ambulances;
-   airport vehicles complying with International Civil Aviation Organisation (ICAO) recommendations.
1.3   This Part of this European Standard deals with the technical requirements to minimize the hazards listed in clause 4 which can arise during the commissioning, the operational use and the routine checking of firefighting and rescue service vehicles when carried out in accordance with the specifications given by the manufacturer or his authorized representative.
   It deals also with performance requirements.
   It does not cover the hazards generated by:
-   noise ( as permanently installed equipment cannot be operated separately from the vehicle, this hazard is covered in Part 2);
-   radiation (low frequ

Feuerwehrfahrzeuge - Teil 3: Fest eingebaute Ausrüstung - Sicherheits- und Leistungsanforderungen

1.1   Der vorliegende Teil dieser Europäischen Norm legt die nach EN 1846-1 und EN 1846-2 geltenden Mindestanforderungen an Sicherheit und Leistung bestimmter optionaler, fest eingebauter und durch geschultes Personal betriebener Ausrüstungen in Feuerwehrfahrzeugen fest.
ANMERKUNG 1   Die für diese Fahrzeuge geltenden Kategorien und Gewichtsklassen sind in EN 1846-1 festgelegt.
Folgende fest eingebaute Ausrüstungen werden im vorliegenden Teil dieser Europäischen Norm behandelt:
   löschtechnische Einrichtung für Wasser;
   löschtechnische Einrichtung für Löschmittelzusatz;
   Werfer;
   Entnahmehilfen.
ANMERKUNG 2   Zusätzlich zum vorliegenden Teil dieser Europäischen Norm sollten einerseits diejenigen nationalen Festlegungen beachtet werden, die für auf öffentlichen Straßen eingesetzte Fahrzeuge gelten, sowie andererseits die auf Fahrzeuge und deren Einrichtungen zutreffenden EU-Richtlinien und damit in Zusammenhang stehenden EFTA-Regelungen.
Für die Anwendung dieser Europäischen Norm gilt als normaler Umgebungstemperaturbereich − 15 °C bis + 35 °C.
ANMERKUNG 3   Bei Einsätzen außerhalb dieses Temperaturbereichs sollte der spezielle Temperaturbereich vom Anwender vorgegeben werden.
1.2   Der vorliegende Teil dieser Europäischen Norm gilt nicht für:
   Fahrzeuge zur Personenbeförderung;
   Fahrzeuge, deren Gesamtgewicht im beladenen Zustand 2 Tonnen nicht überschreitet;
   Boote;
   Flugzeuge;
   Eisenbahnen;
   Krankenkraftwagen;
   Flugfeldfahrzeuge, die den Empfehlungen der Internationalen Zivilen Luftfahrtbehörde (ICAO, International Civil Aviation Organisation) entsprechen.
1.3   Der vorliegende Teil dieser Europäischen Norm enthält die technischen Anforderungen zur Minimierung der in Abschnitt 4 aufgeführten Gefährdungen, die bei der Inbetriebnahme, im Einsatz und bei routinemäßigen Überprüfungen der Feuerwehrfahrzeuge entsprechend den vom Hersteller oder von dessen autorisiertem Vertreter aufgestellten Spezifikationen auftreten können.

Véhicules des services de secours et de lutte contre l'incendie - Partie 3: Equipements installés à demeure - Sécurité et performance

1.1   La présente partie de la présente Norme européenne spécifie les prescriptions minimales de sécurité et de performances de certains équipements optionnels spécifiques installés à demeure sur les véhicules des services de secours et de lutte contre l'incendie, mis en œuvre par des personnels qualifiés, tel que défini dans l'EN 1846 1et spécifié dans l’EN 1846-2.
NOTE 1   Les catégories et les classes de masse des véhicules des services de secours et de lutte contre l'incendie sont données dans l'EN 1846-1.
Les équipements installés à demeure faisant l’objet de la présente partie de la présente Norme européenne sont indiqués ci-dessous :
   installation d'eau ;
   installation d'additif ;
   lance-canon ;
   supports d'équipement.
NOTE 2   Il convient d'utiliser la présente partie de la présente Norme européenne conjointement avec tout règlement national en vigueur pour les véhicules utilisant les voies publiques, ainsi que toute Directive CE et toute réglementation de l'AELE qui y est associée, concernant les véhicules et leurs équipements.
Pour les besoins de la présente Norme européenne, la plage de température ambiante normale s’étend de – 15 °C à + 35 °C.
NOTE 3   Dans le cas d'utilisation à l'extérieur de cette plage de température, il convient que l’utilisateur spécifie la plage de température particulière.
1.2   La présente partie de la présente Norme européenne ne s'applique pas aux :
   véhicules de transport de personnel ;
   véhicules d'une masse totale en charge n'excédant pas 2 t ;
   bateaux ;
   aéronefs ;
   trains ;
   ambulances ;
   véhicules d'aéroport correspondant aux recommandations de l'Organisation de l'Aviation Civile Internationale (OACI).

Gasilska in reševalna vozila - 3. del: Trajno vgrajena oprema - Varnost in zahteve za obnašanje v uporabi

General Information

• Status: Withdrawn
• Publication Date: 03-Dec-2008
• Withdrawal Date: 30-Sep-2013
• ICS: 13.220.10 - Fire-fighting
• ICS: 43.160 - Special purpose vehicles
• Technical Committee: POZ - Požarna varnost
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 25-Sep-2013
• Due Date: 18-Oct-2013
• Completion Date: 01-Oct-2013
• Directive: 2006/42/EC - Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast)
• Directive: 98/37/EC - Machinery
• Mandate: M/079 - Mandate to CEN and CENELEC for standardization in the field of machines
• Mandate: M/396 - Mandate to CEN and Cenelec for standardisation in the field of machinery
• Ref Project: EN 1846-3:2002+A1:2008 - Firefighting and rescue service vehicles - Part 3: Permanently installed equipment - Safety and performance

Relations

• Replaced By: SIST EN 1846-3:2013 - Firefighting and rescue service vehicles - Part 3: Permanently installed equipment - Safety and performance
• Effective Date: 01-Nov-2013
• Replaced By: SIST EN 1846-3:2013 - Firefighting and rescue service vehicles - Part 3: Permanently installed equipment - Safety and performance
• Effective Date: 08-Jun-2022
• Consolidates: SIST EN 1846-3:2003 - Firefighting and rescue service vehicles - Part 3: Permanently installed equipment - Safety and performance
• Effective Date: 18-Jan-2023
• Consolidates: SIST EN 1846-3:2003 - Firefighting and rescue service vehicles - Part 3: Permanently installed equipment - Safety and performance
• Effective Date: 19-Jan-2023

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 1846-3:2003+A1:2009
01-januar-2009
Gasilska in reševalna vozila - 3. del: Trajno vgrajena oprema - Varnost in zahteve
za obnašanje v uporabi
Firefighting and rescue service vehicles - Part 3: Permanently installed equipment -
Safety and performance
Feuerwehrfahrzeuge - Teil 3: Fest eingebaute Ausrüstung - Sicherheits- und
Leistungsanforderungen
Véhicules des services de secours et de lutte contre l'incendie - Partie 3: Equipements
installés à demeure - Sécurité et performance
Ta slovenski standard je istoveten z: EN 1846-3:2002+A1:2008
ICS:
13.220.10 Gašenje požara Fire-fighting
43.160 Vozila za posebne namene Special purpose vehicles
SIST EN 1846-3:2003+A1:2009 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 1846-3:2003+A1:2009

---------------------- Page: 2 ----------------------

SIST EN 1846-3:2003+A1:2009


EUROPEAN STANDARD
EN 1846-3:2002+A1

NORME EUROPÉENNE

EUROPÄISCHE NORM
September 2008
ICS 13.220.10 Supersedes EN 1846-3:2002
English Version
Firefighting and rescue service vehicles - Part 3: Permanently
installed equipment - Safety and performance
Véhicules des services de secours et de lutte contre Feuerwehrfahrzeuge - Teil 3: Fest eingebaute Ausrüstung -
l'incendie - Partie 3: Equipements installés à demeure - Sicherheits- und Leistungsanforderungen
Sécurité et performances
This European Standard was approved by CEN on 9 September 2002 and includes Amendment 1 approved on 30 July 2008.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.






EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1846-3:2002+A1:2008: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 1846-3:2003+A1:2009
EN 1846-3:2002+A1:2008 (E)
Contents
page
Foreword.4
Introduction .5
1 Scope .6
2 Normative references .7
3 Terms and definitions .8
4 List of significant hazards .10
4.1 Water installation.10
4.2 Additive installation.12
4.3 Monitor.14
4.4 Equipment gantries .15
5 Requirements.16
5.1 General.16
5.2 Safety requirements and/or protective measures.16
5.2.1 General.16
5.2.2 Water installation.16
5.2.3 Additive installation.18
5.2.4 Monitor.18
5.2.5 Equipment gantries .19
5.3 Performance requirements .19
5.3.1 General.19
5.3.2 Water installation.19
5.3.3 Additive installation.23
5.3.4 Monitor.25
5.3.5 Equipment gantries .25
6 Verification .26
6.1 General.26
6.2 Verification of the safety requirements and/or measures .26
6.2.1 General.26
6.2.2 Water installation.26
6.2.3 Additive installation.27
6.2.4 Monitor.28
6.2.5 Equipment gantries .28
6.3 Verification of the performance requirements.28
6.3.1 General.28
6.3.2 Water installation.29
6.3.3 Additive installation.30
6.3.4 Monitor.31
6.3.5 Equipment gantries .31
7 Information for use .32
7.1 General.32
7.2 Essential information and marking relevant to safety.32
7.3 Information and marking relevant to performance .32
Annex A (informative) Monitor throw measurement.34
2

---------------------- Page: 4 ----------------------

SIST EN 1846-3:2003+A1:2009
EN 1846-3:2002+A1:2008 (E)
Annex ZA (informative) !Relationship between this European Standard and the Essential
Requirements of EU Directive 98/37EC".35
Annex ZB (informative) !Relationship between this European Standard and the Essential
Requirements of EU Directive 2006/42/EC".36
Bibliography.37

3

---------------------- Page: 5 ----------------------

SIST EN 1846-3:2003+A1:2009
EN 1846-3:2002+A1:2008 (E)
Foreword
This document (EN 1846-3:2002+A1:2008) has been prepared by Technical Committee CEN/TC 192 "Fire service
equipment", the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an identical text or
by endorsement, at the latest by March 2009, and conflicting national standards shall be withdrawn at the latest by
December 2009.
This document includes Amendment 1, approved by CEN on 2008-07-30.
This document supersedes EN 1846-3:2002.
The start and finish of text introduced or altered by amendment is indicated in the text by tags ! ".
The CEN/TC 192 entrusted the drafting of this standard to CEN/TC 192/WG3 "Firefighting and rescue service
vehicles".
This document has been prepared under a mandate given to CEN by the European Commission and the European
Free Trade Association, and supports essential requirements of !EU Directive(s)".
!For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this
document."
EN 1846 "Firefighting and rescue service vehicles" is composed of three parts:
 Part 1: Nomenclature and designation;
 Part 2: Common requirements - Safety and performance;
 Part 3: Permanently installed equipment - Safety and performance.
Annex A is for information only.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden,
Switzerland and United Kingdom.

4

---------------------- Page: 6 ----------------------

SIST EN 1846-3:2003+A1:2009
EN 1846-3:2002+A1:2008 (E)
Introduction
This document is a type C standard as stated in !EN ISO 12100-1:2003".
This document is a complement to EN 1846-2 and deals with some optional specific permanently installed
equipment used by firefighters.
The equipment concerned and the extent to which hazards, hazardous situations and events are covered are
indicated in the scope of this document.
NOTE Other equipment not covered by this document can be dealt with later in another part, depending on the decision of
CEN.
When provisions of this type C standard are different from those which are stated in type A or B standards, the
provisions of this type C standard take precedence over the provisions of the other standards, for machines that
have been designed and built according to the provisions of this type C standard.
This document also deals with the performance requirements which apply to the equipment as defined in the
scope.
5

---------------------- Page: 7 ----------------------

SIST EN 1846-3:2003+A1:2009
EN 1846-3:2002+A1:2008 (E)
1 Scope
1.1 This Part of this European Standard specifies the minimum requirements for safety and performance of
some optional specific permanently installed equipment on firefighting and rescue service vehicles, operated by
trained persons, as designated in EN 1846-1 and specified in EN 1846-2.
NOTE 1 Categories and mass classes of the firefighting and rescue service vehicles are given in EN 1846-1.
The permanently installed equipment dealt with in this Part of this European Standard is given below:
 water installation;
 additive installation;
 monitor;
 equipment gantries.
NOTE 2 This Part of this European Standard should be read in conjunction with any national regulations in force for vehicles
using the public roads and with any EU Directives and associated EFTA regulations in force relevant to vehicles and their
equipment.
For the purposes of this European Standard, the normal ambient temperature range is - 15 °C to + 35 °C.
NOTE 3 In the case of utilization outside this temperature range, the particular temperature range should be specified by the
user.
1.2 This Part of this European Standard is not applicable to:
 personnel carrying vehicles;
 vehicles with a gross laden mass not exceeding 2 t;
 boats;
 aircrafts;
 trains;
 ambulances;
 airport vehicles complying with International Civil Aviation Organisation (ICAO) recommendations.
1.3 This Part of this European Standard deals with the technical requirements to minimize the hazards listed in
clause 4 which can arise during the commissioning, the operational use and the routine checking of firefighting and
rescue service vehicles when carried out in accordance with the specifications given by the manufacturer or his
authorized representative.
It deals also with performance requirements.
It does not cover the hazards generated by:
 noise ( as permanently installed equipment cannot be operated separately from the vehicle, this hazard is
covered in Part 2);
 radiation (low frequency, radio frequency, radiation, microwaves);
 errors in the software;
6

---------------------- Page: 8 ----------------------

SIST EN 1846-3:2003+A1:2009
EN 1846-3:2002+A1:2008 (E)
 use in potentially explosive atmospheres;
 construction, transportation, maintenance and decommissioning;
 wind pressure in and out of use;
 static electricity problems;
 remote control;
 electromagnetic compatibility;
 oil hydraulic and pneumatic driving system.
1.4 This document is not applicable to the equipment which is manufactured before its date of publication by
CEN.
2 Normative references
This European Standard incorporates by dated or undated reference, provisions from other publications. These
normative references are cited at the appropriate places in the text, and the publications are listed hereafter. For
dated references, subsequent amendments to or revisions of any of these publications apply to this European
Standard only when incorporated in it by amendment of revision. For undated references the latest edition of the
publication referred to applies (including amendments).
!deleted text"
EN 418, Safety of machinery – Emergency stop equipment, functional aspects - Principles for design
EN 953, Safety of machinery – Guards – General requirements for the design and construction of fixed and
movable guards
EN 1050:1996, Safety of machinery – Principles for risk assessment
!deleted text"
EN 1028-1:2002, Fire-fighting pumps – Fire-fighting centrifugal pumps with primer – Part 1: Classification, general
and safety requirements
EN 1028-2, Fire-fighting pumps – Fire-fighting centrifugal pumps with primer – Part 2: Verification of general and
safety requirements
EN 1846-1:1998, Firefighting and rescue service vehicles – Part 1: Nomenclature and designation
EN 1846-2:2001, Firefighting and rescue service vehicles – Part 2: Common requirements - Safety and
performance
EN 1846-2:2001/prA1, Firefighting and rescue service vehicles – Part 2: Common requirements - Safety and
performance
prEN 1947, Fire-fighting hoses – Semi-rigid delivery hoses and hose assemblies for pumps and vehicles
!EN ISO 12100-1:2003, Safety of machinery – Basic concepts, general principles for design – Part 1: Basic
terminology, methodology (ISO 12100-1:2003)
EN ISO 12100-2:2003, Safety of machinery – Basic concepts, general principles for design – Part 2: Technical
principles (ISO 12100-2:2003)"
7

---------------------- Page: 9 ----------------------

SIST EN 1846-3:2003+A1:2009
EN 1846-3:2002+A1:2008 (E)
3 Terms and definitions
For the purposes of this Part of this European Standard, the terms and definitions given in
!EN ISO 12100-1:2003", EN 1846-1:1998, EN 1846-2:2001 together with the following apply.
3.1
water installation
combination of components for the collection, storage and delivery of water and/or water-additive mixture at varying
pressures and delivery rates
3.1.1
specified rate(s) of the water installation, Q
1
specified rate(s) corresponding to the nearest lower value(s) in the following list : 250 l/min – 500 l/min – 750 l/min
– 1 000 l/min – 1 500 l/min – 2 000 l/min – 3 000 l/min – 4 000 l/min – 6 000 l/min
3.1.2
specified outlet pressure(s) of the water installation, p
a1
specified outlet pressure(s) corresponding to the nearest lower value(s) in the following list : 6 bar – 10 bar – 15 bar
– 40 bar
3.1.3
height
difference of level between the standing surface of the vehicle and the water surface at the time of a pumping
appliance suction operation
3.1.4
specified height of the water installation, d
specified height where d equals 1,5 m or 3 m
3.1.5
standing surface of the vehicle
surface on which the vehicle wheels are resting when it is operating
3.1.6
standing surface of the operator
surface on which the operator stands
3.1.7
installed water pump
pump permanently installed on a vehicle and driven by the motive power of the vehicle, or a pump complete with
drive motor
3.1.8
installed water tank
container for storage of water for fire service purposes
3.1.9
supply and delivery connections for water
inlet and outlet devices for joining hoses to the pipework installation
3.1.10
pipework installation for water
any system linking the installed water pump(s), the installed water tank(s) and the supply and delivery connections
3.1.11
operating and control instruments for water
controls and gauges necessary to operate and monitor the water installation system
8

---------------------- Page: 10 ----------------------

SIST EN 1846-3:2003+A1:2009
EN 1846-3:2002+A1:2008 (E)
3.1.12
hosereel system
rotating hose storage system with semi-rigid hose(s) permanently connected to the pipework installation
3.1.13
wheeled hosereel
hosereel designed for the storage, the transport and the deployment of layflat hose
3.2
liquid additive
addition to water to enhance firefighting capabilities e.g. foam concentrate, fire retardant
NOTE In this document, the term "additive" means "liquid additive".
3.2.1
additive installation
combination of components for the collection, storage and delivery of additive at varying pressures and delivery
rates before mixing with water
3.2.2
installed additive pump
pump permanently installed on a vehicle and driven by the motive power of the vehicle, or a pump complete with
drive motor
3.2.3
installed additive tank
container for storage of additive for fire service purposes
3.2.4
supply and delivery connections for additive
inlet and outlet devices for joining hoses to the additive installation
3.2.5
pipework installation for additive
any system linking the installed additive pump(s), the additive installed tank(s) and the supply and delivery
connections
3.2.6
operating and control instruments for additive
controls and gauges necessary to operate and monitor the additive installation system
3.3
rated capacity of a tank
capacity of liquid contained in a tank that could be used by the corresponding pump(s)
3.4
mixing system
system to mix the additive (including foam concentrate) with water (and sometimes air) to produce the required
firefighting media
NOTE The mixing system is part of the water and/or additive installation.
3.5
monitor
device permanently fixed on the vehicle for projection of extinguishing agents
3.6
equipment gantry
mechanical system(s) to assist with the loading, unloading and storage of equipment
9

---------------------- Page: 11 ----------------------

SIST EN 1846-3:2003+A1:2009
EN 1846-3:2002+A1:2008 (E)
4 List of significant hazards
The significant hazards relevant to permanently installed equipment which are dealt with in this part of this
European Standard are given in 4.1 to 4.4 (Tables 1 to 4).
4.1 Water installation
Table 1 — List of significant hazards for water installation
Clause/sub-clause
Number of
reference in this
clause /
References to Part 2 Part of this
sub-clause
of this standard or standard (in
in
Corresponding hazard Situation/area
other standards addition to Part 2
EN 1050:
when dealt with in
1996
it)
1 Mechanical hazards
Due to accumulation of
energy inside the machinery Variation of pressure
1 caused, for example, by for firefighters at the / 5.2.2
liquids and gases under end of the branch
pressure
• 5.1.1.4 of
Exposed power take
EN 1846-2:2001
off (PTO)/ /
Entanglement by a powered transmissions
1.4 • EN 953
system
Powered rewind / 5.2.2.7
hosereel(s)
Rupture or piercing of the Exposed parts of the / 5.2.2
1.9
water installation installation
Supply and delivery / 5.2.2.4
1.9 Ejection of coupling
location
3 Thermal hazards
Resulting in burns by contact Exposed parts of the
• 5.2.3 of EN 1028-
3.1 with the pump or by projection pump, pipework and 5.2.2
1:2002
of hot water from the pump delivery connections
7 Hazards generated by materials and substances processed or used by the machine
Bad location of the • 5.1.1.3.2 of
7.1 Inhalation of exhaust gases /
exhaust
EN 1846-2:2001
10

---------------------- Page: 12 ----------------------

SIST EN 1846-3:2003+A1:2009
EN 1846-3:2002+A1:2008 (E)
Table 1 — List of significant hazards for water installation (concluded)
Clause/sub-clause
Number of
reference in this
clause /
References to Part 2 Part of this
sub-clause
of this standard or standard (in
in
Corresponding hazard Situation/area
other standards addition to Part 2
EN 1050:
when dealt with in
1996
it)
Hazards generated by neglecting ergonomic principles in machinery design
8
(see EN 614-1 and prEN 13861)
At the operating • 5.1.3.3/5.1.4.2 of
8.4 Inadequate local lighting /
position EN 1846-2:2001
Mental overload and
• 5.1.4.2 of
8.5
No logical relationship
underload, stress
EN 1846-2:2001
between the command
and the expected 5.2.2.6
rd
• !3 dash of
operation at the
Human error, human
8.6 4.8.7 of EN ISO
operating position
behaviour
12100-2:2003"
• 5.1.4.2/7.3 of
EN 1846-2:2001
Inadequate design, location or
At the operating
8.7 identification of manual /
rd
position
• !3 dash of
controls
4.8.7 of EN ISO
12100-2:2003"
Impossibility of stopping
At the operating
11 the machine in the best / 5.2.1
position
possible conditions
20 Relating to the travelling function
Overturning of vehicle.
Excessive oscillations when
• 5.1.1.1/5.1.1.2 of
20.5 Loss of lateral stability 5.2.2.3
moving EN 1846-2:2001
during braking

11

---------------------- Page: 13 ----------------------

SIST EN 1846-3:2003+A1:2009
EN 1846-3:2002+A1:2008 (E)
4.2 Additive installation
Table 2 — List of significant hazards for additive installation
Clause/sub-clause
Number of
reference in this
clause /
References to Part 2 Part of this
sub-clause
Corresponding hazard Situation/area of this standard or standard (in
in
other standards addition to Part 2
EN 1050:
when dealt with in
1996
it)
1 Mechanical hazards
• 5.1.1.4 of
EN 1846-2:2001
Entanglement by a powered Exposed
1.4 /
system (if pump) PTO/transmissions
• EN 953
Rupture or piercing of the Exposed parts of the
1.9 / 5.2.3.1
additive installation additive installation
Supply and delivery
1.9 Ejection of coupling / 5.2.3.4
location
7 Hazards generated by materials
7.1
Contact with or inhalation of Point of contact with
7.1 /
harmful additive additive
7.2
Bad location of the
• 5.1.1.3.2 of
7.1 Inhalation of exhaust gases /
exhaust EN 1846-2:2001
Hazards generated by neglecting ergonomic principles in machinery design (see EN 614-1 and
8
prEN 13861)
At the operating • 5.1.3.3/5.1.4.2 of
8.4 Inadequate local lighting /
position EN 1846-2:2001
Mental overload and
• 5.1.4.2 of
8.5 No logical relationship
underload, stress EN 1846-2:2001
between the command
and the expected 5.2.3.6
rd
• !3 dash of
operation at the
Human error, human
8.6 4.8.7 of EN ISO
operating position
behaviour
12100-2:2003"
• 5.1.4.2/7.3 of
EN 1846-2:2001
Inadequate design, location or
At the operating
8.7 identification of manual /
rd
position
• !3 dash of
controls
4.8.7 of EN ISO
12100-2:2003"
Confusion between different At the operating
• 5.1.4.2/7.3 of
8.7 /
signals position EN 1846-2:2001
12

---------------------- Page: 14 ----------------------

SIST EN 1846-3:2003+A1:2009
EN 1846-3:2002+A1:2008 (E)
Table 2 — List of significant hazards for additive installation (concluded)
Clause/sub-clause
Number of
reference in this
clause /
References to Part 2 Part of this
sub-clause
Corresponding hazard Situation/area of this standard or standard (in
in
other standards
addition to Part 2
EN 1050:
when dealt with in
1996
it)
Impossibility of stopping
At the operating
11 the machine in the best / 5.2.1
position
possible conditions
20 Relating to the travelling function
Overturning of the
Excessive oscillations when
• 5.1.1.1/5.1.1.2 of
20.5 vehicle. Loss of lateral 5.2.3.3
moving EN 1846-2:2001
stability during braking
13

---------------------- Page: 15 ----------------------

SIST EN 1846-3:2003+A1:2009
EN 1846-3:2002+A1:2008 (E)
4.3 Monitor
Table 3 — List of hazards for monitor
Clause/sub-clause
Number of
reference in this
clause /
References to Part 2 Part of this
sub-clause
Corresponding hazard Situation/area of this standard or standard (in
in
other standards addition to Part 2
EN 1050:
when dealt with in
1996
it)
1 Mechanical hazards
Impact hazard when
monitor is operating :
 movement (when remote
5.2.4
control) ;
1.6 Monitor location /
7
 movement (vertical,
rotation)
Rupture or piercing of the Exposed pipework
1.9 / 5.2.4
pipework system or monitor installation
2 Electrical hazards
Electric shock by 7.1
Full stream on high voltage • 7.1.2.4 of
stream contact on high
2.2
conductors
EN 1846-2:2001
voltage conductors 7.2
7 Hazards generated by materials and substances processed or used by the machine
Bad location of the • 5.1.1.3.2 of
7.1 Inhalation of exhaust gases /
exhaust
EN 1846-2:2001
Hazards generated by neglecting ergonomic principles in machinery design (see EN 614-1 and
8
prEN 13861)
unhealthy postures or At the operating
• 5.1.4.2 of
8.1 /
excessive effort position EN 1846-2:2001
Inadequate lighting of the At the operating • 5.1.3.3/5.1.4.2 of
8.4 /
operating position position
EN 1846-2:2001
Loss of permanent control of At the operating
8.7 / 5.2.4
the monitor position
Confusion between different At the operating • 5.1.4.2/7.3 of
8.7 /
signals position
EN 1846-2:2001
Impossibility of stopping
At the operating
11 the machine in the best / 5.2.1
position
possible conditions
14

---------------------- Page: 16 ----------------------

SIST EN 1846-3:2003+A1:2009
EN 1846-3:2002+A1:2008 (E)
Table 3 — List of hazards for monitor (concluded)
Clause/sub-clause
Number of
reference in this
clause /
References to Part 2 Part of this
sub-clause
Corresponding hazard Situation/area of this standard or standard (in
in
other standards addition to Part 2
EN 1050:
when dealt with in
...