SIST EN 14398-1:2004
(Main)Cryogenic vessels - Large transportable non-vacuum insulated vessels - Part 1: Fundamental requirements
Cryogenic vessels - Large transportable non-vacuum insulated vessels - Part 1: Fundamental requirements
This European Standard specifies the fundamental requirements for large transportable non-vacuum insulated cryogenic vessels and designed to operate above atmospheric pressure.
This standard applies to large transportable non-vacuum insulated cryogenic vessels for fluids as specified in 3.1 and is not applicable to such vessels designed for toxic fluids.
Kryo-Behälter - Große ortsbewegliche, nicht vakuum-isolierte Behälter - Teil 1: Grundanforderungen
Diese Norm legt die Grundanforderungen für große ortsbewegliche, nicht vakuum-isolierte Kryo - Behälter fest, die für einen Betrieb über Atmosphärendruck ausgelegt sind.
Diese Norm gilt für große ortsbewegliche nicht vakuum-isolierte Kryo - Behälter für Fluide, wie in 3.1 definiert, und nicht für solche, die für giftige Fluide ausgelegt sind.
Récipients cryogéniques - Grands récipients transportables non isolés sous vide - Partie 1: Exigences fondamentales
La présente Norme européenne spécifie les exigences fondamentales applicables aux grands récipients cryogéniques transportables, isolés sous vide et conçus pour fonctionner au-dessus de la pression atmosphérique.
La présente norme s'applique aux grands récipients cryogéniques transportables, isolés sous vide, prévus pour des fluides tels que spécifiés en 3.1 et n'est pas applicable aux récipients conçus pour les fluides toxiques.
Kriogene posode – Velike premične, vakuumsko neizolirane posode - 1. del: Osnovne zahteve
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 14398-1:2004
01-junij-2004
.ULRJHQHSRVRGH±9HOLNHSUHPLþQHYDNXXPVNRQHL]ROLUDQHSRVRGHGHO
2VQRYQH]DKWHYH
Cryogenic vessels - Large transportable non-vacuum insulated vessels - Part 1:
Fundamental requirements
Kryo-Behälter - Große ortsbewegliche, nicht vakuum-isolierte Behälter - Teil 1:
Grundanforderungen
Récipients cryogéniques - Grands récipients transportables non isolés sous vide - Partie
1: Exigences fondamentales
Ta slovenski standard je istoveten z: EN 14398-1:2003
ICS:
23.020.40 Proti mrazu odporne posode Cryogenic vessels
(kriogenske posode)
SIST EN 14398-1:2004 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 14398-1:2004
---------------------- Page: 2 ----------------------
SIST EN 14398-1:2004
EUROPEAN STANDARD
EN 14398-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2003
ICS 23.020.40
English version
Cryogenic vessels - Large transportable non-vacuum insulated
vessels - Part 1: Fundamental requirements
Récipients cryogéniques - Grands récipients transportables Kryo-Behälter - Große ortsbewegliche, nicht vakuum-
non isolés sous vide - Partie 1: Exigences fondamentales isolierte Behälter - Teil 1: Grundanforderungen
This European Standard was approved by CEN on 10 July 2003.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2003 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 14398-1:2003 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 14398-1:2004
EN 14398-1:2003 (E)
Contents
Page
Foreword.3
1 Scope .4
2 Normative references .4
3 Terms and definitions.4
4 General requirements.6
5 Mechanical loads .7
6 Chemical effects.8
7 Thermal loads.8
8 Material.8
9 Design, fabrication, inspection and testing .9
10 Marking and labelling .9
11 Final acceptance test.9
12 Periodic inspection.9
Annex A (informative) Tank plates.10
2
---------------------- Page: 4 ----------------------
SIST EN 14398-1:2004
EN 14398-1:2003 (E)
Foreword
This document (EN 14398-1:2003) has been prepared by Technical Committee CEN/TC 268 “Cryogenic vessels”,
the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical text or
by endorsement, at the latest by February 2004, and conflicting national standards shall be withdrawn at the latest
by February 2004.
This document has been prepared under a mandate given to CEN by the European Commission and the European
Free Trade Association, and supports the objectives of the framework Directives on Transport of Dangerous
Goods.
EN 14398 consists of the following Parts under the general title, Cryogenic vessels – Large transportable non-
vacuum insulated vessels:
– Part 1: Fundamental requirements
– Part 2: Design, fabrication, inspection and testing
– Part 3: Operational requirements
Annex A is informative.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal,
Slovakia, Spain, Sweden, Switzerland and the United Kingdom.
3
---------------------- Page: 5 ----------------------
SIST EN 14398-1:2004
EN 14398-1:2003 (E)
1 Scope
This European Standard specifies the fundamental requirements for large transportable non-vacuum insulated
cryogenic vessels and designed to operate above atmospheric pressure.
This standard applies to large transportable non-vacuum insulated cryogenic vessels for fluids as specified in 3.1
and is not applicable to such vessels designed for toxic fluids.
2 Normative references
This European Standard incorporates by dated or undated references, provisions from other publications. These
normative references are cited at the appropriate places in the text, and the publications are listed hereafter. For
dated references, subsequent amendments to or revisions of any of these publications apply to this European
Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the
publication referred to applies (including amendments).
EN 1252-1, Cryogenic vessels - Materials - Part 1: Toughness requirements for temperatures below -80 °C.
EN 1252-2, Cryogenic vessels - Materials - Part 2: Toughness requirements for temperatures between -80°C and
-20 °C.
EN 1626, Cryogenic vessels - Valves for cryogenic service.
EN 1797, Cryogenic vessels - Gas/material compatibility.
EN 10204, Metallic products - Types of inspection documents.
EN 12300, Cryogenic vessels - Cleanliness for cryogenic service.
EN 13648-1, Cryogenic vessels - Safety devices for protection against excessive pressure - Part 1 : Safety valves
for cryogenic service.
EN 13648-2, Cryogenic vessels - Safety devices for protection against excessive pressure - Part 2 : Bursting disc
safety devices for cryogenic service.
EN 13648-3, Cryogenic vessels - Safety devices for protection against excessive pressure - Part 3 : Determination
of required discharge - Capacity and sizing.
EN 14398-2, Cryogenic vessels - Large transportable non-vacuum insulated vessels - Part 2 : Design, fabrication,
inspection and testing.
EN 14398-3, Cryogenic vessels - Large transportable non-vacuum insulated vessels - Part 3: Operational
requirements.
3 Terms and definitions
For the purposes of this European Standard, the following terms and definitions apply.
3.1
cryogenic fluid (refrigerated liquefied gas)
1
gas which is partially liquid because of its low temperature ). In the context of all parts of this standard the
(refrigerated but) non-toxic gases and mixtures of them given in Table 1 are referred to as cryogenic fluids
1
) This includes totally evaporated liquids and supercritical fluids.
4
---------------------- Page: 6 ----------------------
SIST EN 14398-1:2004
EN 14398-1:2003 (E)
Table 1 — Refrigerated but non toxic gases
a
Item and
Identification number, name and description
group
3 A Asphyxiant gases
2187 Carbon dioxide, refrigerated liquid
b
3158 Gas, refrigerated liquid, N.O.S .
3 O Oxidizing gases
2201 Nitrous oxide, refrigerated liquid, oxidizing
b
3311 Gas, refrigerated liquid, oxidizing, N.O.S
a
Item group, identification number, name and description according to ADR 2001
b
N.O.S. = not otherwise specified
3.2
large transportable cryogenic vessel (tank)
thermally insulated vessel of more than 1000 l intended for the transport of one or more cryogenic fluids, consisting
2)
of an inner vessel, an outer jacket , all of the valves and equipment together with any additional framework, this
large transportable cryogenic vessel representing a complete assembly ready for putting into service
3.3
thermal insulation
non-vacuum interspace between the inner vessel and the outer jacket. The space is filled with material to reduce
the heat transfer between the inner vessel and the outer jacket
3.4
2)
inner vessel
vessel intended to contain the cryogenic fluid
3.5
2)
outer jacket
normally not gas-tight weather protection of the thermal insulation and of the inner vessel
3.6
normal operation
intended operation of the vessel at a pressure not greater than the maximum allowable working pressure including
the handling loads defined in 3.7
3.7
handling loads
loads exerted on the transportable cryogenic vessel in all expected situations of transport including loading,
unloading, moving lifting equipment
3.8
documentation
technical documents delivered by the manufacturer to the owner consisting of :
all certificates establishing the conformity with this standard (e.g. material, pressure test, cleanliness, safety
devices);
a short description of the vessel (including characteristic data etc.);
2) The expressions 'inner vessel' and 'outer jacket' where originally introduced for vacuum insulated vessels. They are used in
this set of standards to be consistent with all standards about cryogenic vessels, but in the case of the outer jacket with another
meaning in this set of standards.
5
---------------------- Page: 7 ----------------------
SIST EN 14398-1:2004
EN 14398-1:2003 (E)
a list of fluids and their net mass for which the cryogenic vessel is designed;
an operating manual (for the user) which consists of:
a short description of the vessel (including characteristic data etc.);
a statement that the vessel is in conformity with this standard;
the instructions for normal operation.
3.9
piping system
all pipes which can come in contact with cryogenic fluids including their valves, fittings, pressure relief devices as
well as their supports
3.10
safety accessories
devices which have a safety related function with respect to pressure containment and/or control (e.g. protective or
limiting devices, regulating and monitoring devices, valves, indicators)
3.11
manufacturer of the large transportable cryogenic vessel
company who carries out the final assembly of the large transportable cryogenic vessel
3.12
volume of the inner vessel
volume of the shell, excluding nozzles, pipes etc. determined at minimum design temperature and atmospheric
pressure
3.13
tare mass
mass of the empty large transportable cryogenic vessel
3.14
net mass
maximum allowable mass of the cryogenic fluid which may be filled. The maximum allowable mass is equal or less
3)
of the mass of the cryogenic fluid when filled to 98 % of the volume of the inner vessel in the case of gases of 3A
or 3 O
3.15
gross mass
sum of tare mass plus net mass
3.16
pressure
pressure relative to atmospheric pressure, i. e. gauge pressure
4 General requirements
The large transportable cryogenic vessel shall safely withstand the mechanical and thermal loads and the chemical
effects encountered during pressure test and normal operation. These requirements are deemed to be satisfied if
clauses 5 to 9 a
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.