SIST EN 2235:2009
(Main)Aerospace series - Single and multicore electrical cables, screened and jacketed
Aerospace series - Single and multicore electrical cables, screened and jacketed
This standard specifies the required characteristics, test methods, qualification and acceptance conditions of single and multicore cables, screened, jacketed and multicore, jacketed cables for use in aircraft electrical systems.
Luft- und Raumfahrt - Ein- und mehradrige geschirmte und ummantelte elektrische Leitungen
Diese Norm legt die Anforderungen, Prüfverfahren, Qualifikations- und Abnahmebedingungen für ein- und mehradrige, geschirmte und/oder ummantelte elektrische Leitungen zur Verwendung in elektrischen Bordnetzen fest.
Série aérospatiale - Câbles électriques, mono et multiconducteurs, blindés et gainés
Aeronavtika - Eno- in večžilni električni kabli, oklopljeni in oplaščeni
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.ODãþHQLLuft- und Raumfahrt - Ein- und mehradrige geschirmte und ummantelte elektrische LeitungenSérie aérospatiale - Câbles électriques, mono et multiconducteurs, blindés et gainésAerospace series - Single and multicore electrical cables, screened and jacketed49.060Aerospace electric equipment and systemsICS:Ta slovenski standard je istoveten z:EN 2235:2006SIST EN 2235:2009en,de01-junij-2009SIST EN 2235:2009SLOVENSKI
STANDARD
SIST EN 2235:2009
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 2235June 2006ICS 49.060 English VersionAerospace series - Single and multicore electrical cables,screened and jacketedSérie aérospatiale - Câbles électriques, mono etmulticonducteurs, blindés et gainésLuft- und Raumfahrt - Ein-und mehradrige geschirmte undummantelte elektrische LeitungenThis European Standard was approved by CEN on 6 January 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2006 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 2235:2006: ESIST EN 2235:2009
EN 2235:2006 (E) 2 Contents Page Foreword.3 1 Scope.4 2 Normative references.4 3 Terms and definitions.4 4 Materials and construction of cables.4 5 Required characteristics.7 6 Tests methods.7 7 Quality assurance.10 8 Identification marking.12 9 Packaging, labelling and delivery lengths.12
SIST EN 2235:2009
EN 2235:2006 (E) 3 Foreword This European Standard (EN 2235:2006) has been prepared by the European Association of Aerospace Manufacturers - Standardization (AECMA-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2006, and conflicting national standards shall be withdrawn at the latest by December 2006. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.
SIST EN 2235:2009
EN 2235:2006 (E) 4 1 Scope This standard specifies the required characteristics, test methods, qualification and acceptance conditions of single and multicore cables, screened, jacketed and multicore, jacketed cables for use in aircraft electrical systems. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 2574, Aircraft — Electrical cables — Identification marking. ISO 8815, Aircraft — Electrical cables and cable harnesses — Vocabulary. EN 2083, Aerospace series — Copper or copper alloy conductors for electrical cables — Product standard. EN 2084, Aerospace series — Cables, electric, single-core, general purpose, with conductors in copper or copper alloy — Technical specification. EN 3475-100*, Aerospace series — Cables, electrical, aircraft use — Test methods — Part 100: General. EN 3838, Aerospace series — Requirements and tests on user-applied markings on aircraft electrical cables. 1) EN 4434, Aerospace series — Copper or copper alloy lightweight conductors for electrical cables — Product standard (Normal and tight tolerances). EN 9133, Aerospace series — Quality management systems — Qualification Procedure for Aerospace Standard Parts. 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 8815 and EN 3475-100 apply. 4 Materials and construction of cables 4.1 General The individual cores shall conform to EN 2083, EN 2084 or EN 4434 and the product standards. 4.2 Materials The materials shall conform to the product standard. The materials used shall have no corrosive effect upon the conductors and screens and shall not be susceptible to attack by mould and other micro-organisms.
* And all parts quoted in this standard. 1) Published as AECMA Prestandard at the date of publication of this standard. SIST EN 2235:2009
EN 2235:2006 (E) 5 4.3 Construction of cables 4.3.1 General The permissible operating temperature of conductors shall not be lower than the maximum operating temperature of the cable as a whole. 4.3.2 Cabled cores The lay length of the outer lay shall not be less than eight times and not more than 16 times the nominal diameter of the cabled cores. The core shall not be spliced. Where filler cores are used, this shall be specified in the product standard. 4.3.3 Screened cables 4.3.3.1 General The individual strands used for the screen shall be free from kinks, loops or breaks; their surface shall be free from corrosion and other contamination. They shall satisfy the mechanical tests in EN 3475-505 to EN 3475-508 before use. The screen shall be in contact with all the cabled cores. Where spiral screening is used, the lay direction shall be contrary to that of the cabled cores. 4.3.3.2 Joints Joints in the individual strands of the screen shall be made by soldering or by laying the individual strands together over a length of at least 10 mm. There shall be no more than one joint per 3 m cable length (measured between different individual strands). 4.3.3.3 Braid screen pushback capability In accordance with Table 1, test 6.42. 4.3.3.4 Angle of spiral screening or braiding The angle γ of spiral screening or braiding (as shown in Figure 1), measured against the longitudinal axis of the cable shall be at least 10°. 4.3.3.5 Screen coverage The screen shall have a coverage β of at least 90 % for spiral screening and at least 85 % for braiding. SIST EN 2235:2009
EN 2235:2006 (E) 6 Ø DU'UndαγS Figure 1 — Screen Coverage
The cable covering is calculated using the following formula: for spirals: U = π (D + d) and S = π (D + d) tan α F = U’ Z / U = n d Z / [π (D + d) sin α] β = F × 100 (%) for braids: U = π (D + 2d) and S = π (D + 2d) tan α For braids, the filling factor F and coverage β, taking into account both braiding directions and a symmetrical braiding pattern are: F = (U’/ U) (Z / 2) = {n d / [π (D + 2d) sin α]} (Z / 2)
and
β = F (2 − F) × 100 (%) where: S = lay length of screen in mm D = diameter under screen in mm (for cables with two or
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.