SIST EN 2235:2015
(Main)Aerospace series - Single and multicore electrical cables, screened and jacketed - Technical specification
Aerospace series - Single and multicore electrical cables, screened and jacketed - Technical specification
This European Standard specifies the required characteristics, test methods, qualification and acceptance
conditions of single and multicore cables, screened, jacketed and multicore jacketed cables for use in aircraft
electrical systems.
Luft- und Raumfahrt - Ein- und mehradrige geschirmte und ummantelte elektrische Leitungen - Technische Lieferbedingungen
Série aérospatiale - Câbles électriques, mono et multiconducteurs, blindés et gainés - Spécification technique
La présente Norme Européenne spécifie les caractéristiques requises, les méthodes d’essais, les conditions de qualification et d’acceptation des câbles mono et multiconducteurs, blindés, gainés et des câbles multiconducteurs gainés utilisés dans les systèmes électriques des aéronefs.
Aeronavtika - Eno- in večžilni električni kabli, oklopljeni in oplaščeni - Tehnična specifikacija
Ta evropski standard določa zahtevane lastnosti, preskusne metode, kvalifikacije in pogoje sprejemljivosti eno- in večžilnih oklopljenih in oplaščenih električnih kablov ter večžilnih oplaščenih kablov za uporabo v letalskih električnih sistemih.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.VSHFLILNDFLMDLuft- und Raumfahrt - Ein- und mehradrige geschirmte und ummantelte elektrische Leitungen - Technische LieferbedingungenSérie aérospatiale - Câbles électriques, mono et multiconducteurs, blindés et gainés - Spécification techniqueAerospace series - Single and multicore electrical cables, screened and jacketed - Technical specification49.060Aerospace electric equipment and systems29.060.20KabliCablesICS:Ta slovenski standard je istoveten z:EN 2235:2015SIST EN 2235:2015en,fr,de01-oktober-2015SIST EN 2235:2015SLOVENSKI
STANDARDSIST EN 2235:20091DGRPHãþD
SIST EN 2235:2015
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 2235
August 2015 ICS 49.060 Supersedes EN 2235:2006English Version
Aerospace series - Single and multicore electrical cables, screened and jacketed - Technical specification
Série aérospatiale - Câbles électriques, mono et multiconducteurs, blindés et gainés - Spécification technique
Luft- und Raumfahrt - Ein- und mehradrige geschirmte und ummantelte elektrische Leitungen - Technische Lieferbedingungen This European Standard was approved by CEN on 29 November 2014.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2015 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 2235:2015 ESIST EN 2235:2015
EN 2235:2015 (E) 2 Contents
Page European foreword .3 1 Scope .4 2 Normative references .4 3 Terms and definitions .4 4 Materials and construction of cables .4 5 Required characteristics .7 6 Tests methods .7 7 Quality assurance . 11 8 Identification marking . 13 9 Packaging, labelling and delivery lengths . 13
SIST EN 2235:2015
EN 2235:2015 (E) 3 European foreword This document (EN 2235:2015) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2016, and conflicting national standards shall be withdrawn at the latest by February 2016. This document supersedes EN 2235:2006. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. SIST EN 2235:2015
EN 2235:2015 (E) 4 1 Scope This European Standard specifies the required characteristics, test methods, qualification and acceptance conditions of single and multicore cables, screened, jacketed and multicore jacketed cables for use in aircraft electrical systems. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
EN 2083, Aerospace series — Copper or copper alloy conductors for electrical cables — Product standard EN 2084, Aerospace series — Cables, electrical, single-core, general purpose, with conductors in copper or copper alloy — Technical specification EN 3475-100 (all parts), Aerospace series — Cables, electrical, aircraft use — Test methods — Part 100: General EN 3838, Aerospace series — Requirements and tests on user-applied markings on aircraft electrical cables EN 4434, Aerospace series — Copper or copper alloy lightweight conductors for electrical cables — Product standard (Normal and tight tolerances) EN 9133, Aerospace series — Quality management systems — Qualification procedure for aerospace standard parts ISO 2574, Aircraft — Electrical cables — Identification marking ISO 8815, Aircraft — Electrical cables and cable harnesses — Vocabulary 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 8815 and EN 3475-100 apply. 4 Materials and construction of cables 4.1 General The individual cores shall be qualified to EN 2083 or EN 4434, EN 2084 and the product standards. 4.2 Materials The materials shall conform to the product standard. 4.3 Construction of cables 4.3.1 General The permissible operating temperature of conductors shall not be lower than the maximum operating temperature of the cable as a whole. SIST EN 2235:2015
EN 2235:2015 (E) 5 4.3.2 Cabled cores The lay length of the outer lay shall not be less than eight times and not more than 16 times the nominal diameter of the cabled cores. The core shall not be spliced. Where filler cores are used, this shall be specified in the product standard. 4.3.3 Screened cables 4.3.3.1 General The individual strands used for the screen shall be free from kinks, loops or breaks; their surface shall be free from corrosion and other contamination. They shall satisfy the mechanical tests in EN 3475-505 to EN 3475-508 before use. The screen shall be in contact with all the cabled cores. Where spiral screening is used, the lay direction shall be contrary to that of the cabled cores. 4.3.3.2 Joints Joints in the individual strands of the screen shall be made by soldering or by laying the individual strands together over a length of at least 10 mm. There shall be no more than one joint per 3 m cable length (measured between different individual strands). 4.3.3.3 Braid screen pushback capability In accordance with Table 1, test 6.48. 4.3.3.4 Angle of spiral screening or braiding The angle γ=of spiral screening or braiding (as shown in Figure 1), measured against the longitudinal axis of the cable shall be at least 10°. 4.3.3.5 Screen coverage The screen shall have a coverage β=of at least 90 % for spiral screening and at least 85 % for braiding. SIST EN 2235:2015
EN 2235:2015 (E) 6
Figure 1 — Screen coverage The cable covering is calculated using the following formula: for spirals: U = π (D + d) and S = π (D + d) tan α F = U’ Z / U = n d Z / [π (D + d) sin α] β = F × 100 (%) for braids: U = π (D + 2d) and S = π (D + 2d) tan α For spiral screen: the maximum length T of the non-covered area is 2 mm, and the relative aperture (versus lay length) of the screening 100 T/L shall be less than 5 %.
Figure 2
SIST EN 2235:2015
EN 2235:2015 (E) 7 For braids, the filling factor F and coverage β, taking into account both braiding directions and a symmetrical braiding pattern are: F = (U’/ U) (Z / 2) = {n d / [π (D + 2d) sin α]} (Z / 2) and β = F (2 − F) × 100 (%) where S = lay length of screen in mm; D = diameter under screen in mm (for cables with 2 or more cores without fillers: D ==(π=+=N) b / π); d = diameter of screen strands in mm;
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.