SIST EN ISO 3994:2011
(Main)Plastics hoses - Helical-thermoplastic-reinforced thermoplastics hoses for suction and discharge of aqueous materials - Specification (ISO 3994:2007)
Plastics hoses - Helical-thermoplastic-reinforced thermoplastics hoses for suction and discharge of aqueous materials - Specification (ISO 3994:2007)
This International Standard specifies the requirements for three types of helical-thermoplastic-reinforced thermoplastics hoses for suction and discharge of water, weak aqueous chemical solutions and abrasive solids and slurries, for use in the ambient temperature range from 10 °C to 55 °C. The three types of hose are for light-, medium- and heavy-duty applications. The types of hoses covered in this International Standard are not intended for use with flammable or combustible materials, nor with aromatic solvents.
Kunststoffschläuche - Mit einer thermoplastischen Wendel verstärkte thermoplastische Schläuche zum Ansaugen und Fördern wässriger Stoffe - Anforderung (ISO 3994:2007)
Diese Internationale Norm legt Anforderungen fest für drei Arten von thermoplastischen Schläuchen verstärkt mit einer Thermoplastischen Wendel zum Ansaugen und Fördern von Wasser, verdünnten wässrigen Chemikalienlösungen und abrasiven Feststoffen und Schlämmen für den Gebrauch in einem Umgebungstemperaturbereich von 10 °C bis 55 °C.
Diese drei Arten von Schläuchen sind anwendbar für leichte, mittlere und schwere Beanspruchungen
Die in dieser Internationalen Norm enthaltenen Schlaucharten sind nicht bestimmt für die Verwendung mit entflammbaren und brennbaren Materialien, auch nicht mit aromatischen Lösungsmitteln.
ANMERKUNG Schläuche mit ähnlichem Aufbau zum Ansaugen und Fördern für die Feuerbekämpfung sind in ISO 14775 Fire fighting hoses — Rubber and plastics suction hoses and hose assemblies festgelegt.
Tuyaux en plastiques - Tuyaux thermoplastiques à renforcement thermoplastique en spirale pour aspiration et refoulement de matières aqueuses - Spécifications (ISO 3994:2007)
L'ISO 3994:2007 spécifie les exigences pour trois types de tuyaux thermoplastiques à renforcement thermoplastique en spirale pour aspiration et refoulement d'eau, de solutions chimiques aqueuses faibles et de solides abrasifs et en suspension, pour une utilisation dans une plage de températures allant de − 10 °C à + 55 °C.
Les trois types de tuyaux sont prévus pour des applications légères, moyennes et lourdes. Ils ne sont pas prévus pour une utilisation avec des matériaux inflammables et combustibles, ni avec des solvants aromatiques.
Plastične cevi - S termoplastično spiralo ojačene termoplastične cevi za sesanje in odvajanje vodnih materialov - Specifikacija (ISO 3994:2007)
Ta mednarodni standard določa zahteve za tri vrste s termoplastično spiralo ojačenih termoplastičnih cevi za sesanje in odvajanje vode, šibkih vodnih kemičnih raztopin in abrazivnih trdnih in tekočih zmesi, ki se uporabljajo v območju okoljske temperature med 10 °C in 55 °C. Tri vrste cevi so namenjene uporabi pri lahki, srednji in težki obremenitvi. Vrste cevi, ki jih zajema ta mednarodni standard, niso primerne za uporabo z vnetljivimi ali gorljivimi materiali in z aromatskimi topili.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Kunststoffschläuche - Mit einer thermoplastischen Wendel verstärkte thermoplastische Schläuche zum Ansaugen und Fördern wässriger Stoffe - Anforderung (ISO 3994:2007)Tuyaux en plastiques - Tuyaux thermoplastiques à renforcement thermoplastique en spirale pour aspiration et refoulement de matières aqueuses - Spécifications (ISO 3994:2007)Plastics hoses - Helical-thermoplastic-reinforced thermoplastics hoses for suction and discharge of aqueous materials - Specification (ISO 3994:2007)23.040.70Gumene cevi in armatureHoses and hose assembliesICS:Ta slovenski standard je istoveten z:EN ISO 3994:2011SIST EN ISO 3994:2011en,fr01-september-2011SIST EN ISO 3994:2011SLOVENSKI
STANDARDSIST EN ISO 3994:20001DGRPHãþD
SIST EN ISO 3994:2011
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN ISO 3994
May 2011 ICS 23.040.70 Supersedes EN ISO 3994:2000English Version
Plastics hoses - Helical-thermoplastic-reinforced thermoplastics hoses for suction and discharge of aqueous materials - Specification (ISO 3994:2007)
Tuyaux en plastiques - Tuyaux thermoplastiques à renforcement thermoplastique en spirale pour aspiration et refoulement de matières aqueuses - Spécifications (ISO 3994:2007)
Kunststoffschläuche - Mit einer thermoplastischen Wendel verstärkte thermoplastische Schläuche zum Ansaugen und Fördern wässriger Stoffe - Anforderung (ISO 3994:2007) This European Standard was approved by CEN on 15 April 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 3994:2011: ESIST EN ISO 3994:2011
EN ISO 3994:2011 (E) 2 Contents Page Foreword .3 SIST EN ISO 3994:2011
EN ISO 3994:2011 (E) 3 Foreword The text of ISO 3994:2007 has been prepared by Technical Committee ISO/TC 45 “Rubber and rubber products” of the International Organization for Standardization (ISO) and has been taken over as EN ISO 3994:2011 by Technical Committee CEN/TC 218 “Rubber and plastics hoses and hose assemblies” the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2011, and conflicting national standards shall be withdrawn at the latest by November 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 3994:2000. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 3994:2007 has been approved by CEN as a EN ISO 3994:2011 without any modification.
SIST EN ISO 3994:2011
SIST EN ISO 3994:2011
Reference numberISO 3994:2007(E)© ISO 2007
INTERNATIONAL STANDARD ISO3994Third edition2007-08-15Plastics hoses — Helical-thermoplastic-reinforced thermoplastics hoses for suction and discharge of aqueous materials — Specification Tuyaux en plastiques — Tuyaux thermoplastiques à renforcement thermoplastique en spirale pour aspiration et refoulement de matières aqueuses — Spécifications
SIST EN ISO 3994:2011
ISO 3994:2007(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
©
ISO 2007 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
copyright@iso.org Web
www.iso.org Published in Switzerland
ii © ISO 2007 – All rights reserved
SIST EN ISO 3994:2011
ISO 3994:2007(E) © ISO 2007 – All rights reserved iiiContents Page Foreword.iv Introduction.v 1 Scope.1 2 Normative references.1 3 Terms and definitions.2 4 Classification.2 5 Materials and construction.2 6 Dimensions and tolerances.2 6.1 Nominal bores, internal diameters and tolerances.2 6.2 Length tolerances.2 7 Performance requirements.3 7.1 Hydrostatic testing at 23 °C ± 2 °C.3 7.2 Hydrostatic testing at 55 °C ± 2 °C.4 7.3 Maximum working pressure.4 7.4 Tensile adhesion test.5 7.5 Vacuum test.5 7.6 Reinforcement fracture test.5 7.7 Minimum bend radius.6 7.8 Cold-bend radius.6 7.9 Loss in mass on heating.6 7.10 Exposure to xenon-arc lamp.6 8 Type, routine and production testing.7 9 Marking.7 10 Recommendations for packing and storage.7 Annex A (normative)
Tensile adhesion test.8 Annex B (normative)
Vacuum test.10 Annex C (normative)
Reinforcement fracture test.11 Annex D (normative)
Type and routine tests.13 Annex E (informative)
Recommended tests for production testing.14
SIST EN ISO 3994:2011
ISO 3994:2007(E) iv © ISO 2007 – All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 3994 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 1, Hoses (rubber and plastics). This third edition cancels and replaces the second edition (ISO 3994:1998), which has been technically revised. SIST EN ISO 3994:2011
ISO 3994:2007(E) © ISO 2007 – All rights reserved vIntroduction This International Standard has been prepared to provide minimum acceptable requirements for the satisfactory performance of polymer-reinforced thermoplastics hoses for suction and discharge applications, conveying water, weak aqueous chemical solutions and abrasive solids and slurries. If there is a special requirement for resistance to deleterious chemicals, this shall be a matter for agreement between the supplier and the purchaser. SIST EN ISO 3994:2011
SIST EN ISO 3994:2011
INTERNATIONAL STANDARD ISO 3994:2007(E) © ISO 2007 – All rights reserved 1Plastics hoses — Helical-thermoplastic-reinforced thermoplastics hoses for suction and discharge of aqueous materials — Specification WARNING — Persons using this International Standard should be familiar with normal laboratory practice. This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user to establish appropriate health and safety practices and to ensure compliance with any national regulatory conditions. 1 Scope This International Standard specifies the requirements for three types of helical-thermoplastic-reinforced thermoplastics hoses for suction and discharge of water, weak aqueous chemical solutions and abrasive solids and slurries, for use in the ambient temperature range from − 10 °C to + 55 °C. The three types of hose are for light-, medium- and heavy-duty applications. The types of hoses covered in this International Standard are not intended for use with flammable or combustible materials, nor with aromatic solvents. NOTE Hoses of a similar construction for suction and discharge for fire-fighting are specified in ISO 14557, Fire-fighting hoses — Rubber and plastics suction hoses and hose assemblies. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 37, Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties ISO 176:2005, Plastics — Determination of loss of plasticizers — Activated carbon method ISO 1307, Rubber and plastics hoses — Hose sizes, minimum and maximum inside diameters, and tolerances on cut-to-length hoses ISO 1402, Rubber and plastics hoses and hose assemblies — Hydrostatic testing ISO 1746, Rubber or plastics hoses and tubing — Bending tests ISO 4672, Rubber and
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.