SIST EN 60684-3-403 to 405:2004

Flexible insulating sleeving -- Part 3: Specification for individual types of sleeving -- Sheets 403 to 405: Glass textile sleeving with acrylic based coating

Gives the requirements for three types of E-type glass sleeving using either braided or knitted construction with a continuous acrylic based coating, and differentiated by their breakdown voltage: high breakdown voltage (sheet 403), medium breakdown voltage (sheet 404) and low breakdown voltage (sheet 405). These sleevings have been found suitable for use at temperatures up to 155 °C.
Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone.

Isolierschläuche -- Teil 3: Anforderungen für einzelne Schlauchtypen -- Blätter 403 bis 405: Glasfilament-Textilschläuche mit Acrylbeschichtung

Gaines isolantes souples -- Partie 3: Spécification pour types particuliers de gaines -- Feuilles 403 à 405: Gaines en fibre de verre tissées, avec revêtement acrylique

Donne les prescriptions relatives à trois types de gaines tressées ou tricotées en verre de type E avec un revêtement acrylique continu, et différenciées par leur tension de claquage: rigidité diélectrique élevée (feuille 403), rigidité diélectrique moyenne (feuille 404), rigidité diélectrique faible (feuille 405). Les gaines peuvent être utilisées à des températures allant jusqu'à 155 °C.
Les matériaux conformes à cette spécification satisfont à des niveaux établis de performance. Cependant, il convient que le choix d'un matériau par un utilisateur pour une application spécifique soit fondé sur les exigences réelles nécessaires pour une performance adéquate de cette application, et non fondé sur cette seule spécification.

Gibke izolacijske cevi - 3. del: Specifikacije za posamezne tipe cevi - Listi od 403 do 405: Steklo tekstilne cevi s prevleko na akrilni osnovi (IEC 60684-3-403 to 405:2002)

General Information

• Status: Published
• Publication Date: 31-Aug-2004
• ICS: 29.035.30 - Glass and ceramic insulating materials
• Technical Committee: IZO - Insulating materials
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 01-Sep-2004
• Due Date: 01-Sep-2004
• Completion Date: 01-Sep-2004
• Ref Project: EN 60684-3-403 to 405:2002 - Flexible insulating sleeving - Part 3: Specification for individual types of sleeving - Sheets 403 to 405: Glass textile sleeving with acrylic based coating

Relations

• Replaces: SIST HD 523.3.403 to 405 S1:1998 - Specification for flexible insulating sleeving -- Part 3: Specification requirements for individual types of sleeving -- Sheets 403 to 405: Glass textile sleeving with acrylic based coating
• Effective Date: 28-Jan-2023
• Replaces: SIST HD 523.3.403 to 405 S1:1998 - Specification for flexible insulating sleeving -- Part 3: Specification requirements for individual types of sleeving -- Sheets 403 to 405: Glass textile sleeving with acrylic based coating
• Effective Date: 06-May-2014

Standards Content (Sample)

SLOVENSKI SIST EN 60684-3-403 to
405:2004

STANDARD
september 2004
Gibke izolacijske cevi - 3. del: Specifikacije za posamezne tipe cevi - Listi od
403 do 405: Steklo tekstilne cevi s prevleko na akrilni osnovi (IEC 60684-3-403
to 405:2002)
Flexible insulating sleeving - Part 3: Specification for individual types of sleeving -
Sheets 403 to 405: Glass textile sleeving with acrylic based coating (IEC 60684-3-
403 to 405:2002)
ICS 29.035.30 Referenčna številka
SIST EN 60684-3-403 to 405:2004(en)
©  Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD EN 60684-3-403 to 405
NORME EUROPÉENNE
EUROPÄISCHE NORM July 2002
ICS 29.035.20 Supersedes HD 523.3.403 to 405 S1:1990
English version
Flexible insulating sleeving
Part 3: Specification for individual types of sleeving
Sheets 403 to 405: Glass textile sleeving with acrylic based coating
(IEC 60684-3-403 to 405:2002)
Gaines isolantes souples Isolierschläuche
Partie 3: Spécification pour Teil 3: Anforderungen für einzelne
types particuliers de gaines Schlauchtypen
Feuilles 403 à 405: Gaines en fibre de Blätter 403 bis 405: Glasfilament-
verre tissées, avec revêtement acrylique Textilschläuche mit Acrylbeschichtung
(CEI 60684-3-403 to 405:2002) (IEC 60684-3-403 to 405:2002)
This European Standard was approved by CENELEC on 2002-07-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic,
Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta,
Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels
© 2002 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60684-3-403 to 405:2002 E

---------------------- Page: 2 ----------------------

EN 60684-3-403 to 405:2002 - 2 -
Foreword
The text of document 15C/1349/FDIS, future edition 2 of IEC 60684-3-403 to 405, prepared by
SC 15C, Specifications, of IEC TC 15, Insulating materials, was submitted to the IEC-CENELEC
parallel vote and was approved by CENELEC as EN 60684-3-403 to 405 on 2002-07-01.
This European Standard supersedes HD 523.3.403 to 405 S1:1990.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2003-04-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2005-07-01
Annexes designated "normative" are part of the body of the standard.
In this standard, annex ZA is normative.
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 60684-3-403 to 405:2002 was approved by CENELEC as a
European Standard without any modification.
__________

---------------------- Page: 3 ----------------------

- 3 - EN 60684-3-403 to 405:2002
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions of any
of these publications apply to this European Standard only when incorporated in it by amendment or
revision. For undated references the latest edition of the publication referred to applies (including
amendments).
NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
Publication Year Title EN/HD Year
IEC 60684-1 1980 Specification for flexible insulating EN 60684-1 1995
sleeving
Part 1: Definitions and general
requirements
IEC 60684-2 1997 Part 2: Methods of test EN 60684-2 1997
IEC 60757 1983 Code for designation of colours HD 457 S1 1985

---------------------- Page: 4 ----------------------

NORME CEI
INTERNATIONALE IEC
60684-3-403
INTERNATIONAL
à/to 405
STANDARD
Deuxième édition
Second edition
2002-05
Gaines isolantes souples –
Partie 3:
Spécification pour types particuliers de gaines –
Feuilles 403 à 405: Gaines en fibre de verre
tissées, avec revêtement acrylique
Flexible insulating sleeving –
Part 3:
Specification for individual types of sleeving –
Sheets 403 to 405: Glass textile sleeving
with acrylic based coating
 IEC 2002 Droits de reproduction réservés  Copyright - all rights reserved
Aucune partie de cette publication ne peut être reproduite ni No part of this publication may be reproduced or utilized in any
utilisée sous quelque forme que ce soit et par aucun procédé, form or by any means, electronic or mechanical, including
électronique ou mécanique, y compris la photocopie et les photocopying and microfilm, without permission in writing from
microfilms, sans l'accord écrit de l'éditeur. the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: [phone] Telefax: [phone] E-mail: [e-mail]  Web: www.iec.ch
CODE PRIX
J
PRICE CODE
Commission Electrotechnique Internationale
International Electrotechnical Commission
Международная Электротехническая Комиссия
Pour prix, voir catalogue en vigueur
For price, see current catalogue

---------------------- Page: 5 ----------------------

60684-3-403 to 405 © IEC:2002 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
___________
FLEXIBLE INSULATING SLEEVING –
Part 3: Specification for individual types of sleeving –
Sheets 403 to 405: Glass textile sleeving with acrylic based coating
FOREWORD
1) The IEC (International Electrotechnical Commission) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of the IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, the IEC publishes International Standards. Their preparation is
entrusted to technical committees; any IEC National Committee interested in the subject dealt with may
participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. The IEC collaborates closely with the International Organization
for Standardization (ISO) in accordance with conditions determined by agreement between the two
organizations.
2) The formal decisions or agreements of the IEC on technical matters express, as nearly as possible, an
international consensus of opinion on the relevant subjects since each technical committee has representation
from all interested National Committees.
3) The documents produced have the form of recommendations for international use and are published in the form
of standards, technical specifications, technical reports or guides and they are accepted by the National
Committees in that sense.
4) In order to promote international unification, IEC National Committees undertake to apply IEC International
Standards transparently to the maximum extent possible in their national and regional standards. Any
divergence between the IEC Standard and the corresponding national or regional standard shall be clearly
indicated in the latter.
5) The IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with one of its standards.
6) Attention is drawn to the possibility that some of the elements of this International Standard may be the subject
of patent rights. The IEC shall not be held responsible for identifying any or all such
...