SIST EN 13523-24:2017
(Main)Coil coated metals - Test methods - Part 24: Resistance to blocking and pressure marking
Coil coated metals - Test methods - Part 24: Resistance to blocking and pressure marking
This part of EN 13523 specifies the procedure for determining the resistance to blocking and/or pressure marking of an organic coating on a metallic substrate.
Bandbeschichtete Metalle - Prüfverfahren - Teil 24: Block- und Stapelfestigkeit
Dieser Teil der Normenreihe EN 13523 legt ein Verfahren zum Bestimmen der Widerstandsfähigkeit einer organischen Beschichtung auf einem metallischen Substrat gegen Blocken und/oder Markieren von Druckstellen fest.
Tôles prélaquées - Méthodes d'essai Partie 24 : Résistance à l'adhérence et au marbrage
La présente partie de la série de normes EN 13523 spécifie le mode opératoire de détermination de la résistance à l’adhérence et/ou au marbrage d’un revêtement organique appliqué sur un subjectile métallique.
Prevlečene kovine, ki se navijajo - Preskusne metode - 24. del: Odpornost proti zlepljanju in poškodbam zaradi pritiska
Ta del standarda EN 13523 določa postopek za določanje odpornosti na zlepljanje in/ali poškodbe zaradi pritiska organske prevleke na kovinski podlagi.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Bandbeschichtete Metalle - Prüfverfahren - Teil 24: Block- und StapelfestigkeitTôles prélaquées - Méthodes d'essai
Partie 24 : Résistance à l'adhérence et au marbrageCoil coated metals - Test methods - Part 24: Resistance to blocking and pressure marking25.220.60Organske prevlekeOrganic coatingsICS:Ta slovenski standard je istoveten z:EN 13523-24:2017SIST EN 13523-24:2017en,fr,de01-december-2017SIST EN 13523-24:2017SLOVENSKI
STANDARDSIST EN 13523-24:20051DGRPHãþD
SIST EN 13523-24:2017
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13523-24
July
t r s y ICS
t wä t t rä x r Supersedes EN
s u w t uæ t vã t r r vEnglish Version
Coil coated metals æ Test methods æ Part
t vã Resistance to blocking and pressure marking Tôles prélaquées æ Méthodes d 5essai
Partie
t v ã Résistance à l 5adhérence et au marbrage
Bandbeschichtete Metalle æ Prüfverfahren æ Teil
t vã Blockæ und Stapelfestigkeit This European Standard was approved by CEN on
t s May
t r s yä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
9
t r s y CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s u w t uæ t vã t r s y ESIST EN 13523-24:2017
EN 13523-24:2017 (E) 2 Contents Page European foreword . 3 Introduction . 5 1 Scope . 6 2 Normative references . 6 3 Principle . 6 4 Apparatus . 6 5 Sampling . 6 6 Test panels . 6 7 Procedure. 6 7.1 General . 6 7.2 Evaluation . 7 7.2.1 Blocking/sticking . 7 7.2.2 Transfer of gloss and pressure marks . 8 8 Expression of results . 8 9 Precision . 8 10 Test report . 8 Bibliography . 9
SIST EN 13523-24:2017
EN 13523-24:2017 (E) 3 European foreword This document (EN 13523-24:2017) has been prepared by Technical Committee CEN/TC 139 “Paints and varnishes”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2018, and conflicting national standards shall be withdrawn at the latest by January 2018. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 13523-24:2004. The main changes compared to the previous edition are: a) the in-laboratory jargon “eye to the sky” and “eye horizontal” are explained to a more technical term; b) the terms “light” and “heavy” in 7.2.2 are explained; c) the text has been editorially revised and the normative references have been updated. The EN 13523 series, Coil coated metals — Test methods, consists of the following parts: — Part 0: General introduction — Part 1: Film thickness — Part 2: Gloss — Part 3: Colour difference — Instrumental comparison — Part 4: Pencil hardness — Part 5: Resistance to rapid deformation (impact test) — Part 6: Adhesion after indentation (cupping test) — Part 7: Resistance to cracking on bending (T-bend test) — Part 8: Resistance to salt spray (fog) — Part 9: Resistance to water immersion — Part 10: Resistance to fluorescent UV radiation and water condensation — Part 11: Resistance to solvents (rubbing test) — Part 12: Resistance to scratching — Part 13: Resistance to accelerated ageing by the use of heat SIST EN 13523-24:2017
EN 13523-24:2017 (E) 4 — Part 14: Chalking (Helmen method) — Part 15: Metamerism — Part 16: Resistance to abrasion — Part 17: Adhesion of strippable films — Part 18: Resistance to staining — Part 19: Panel design and method of atmosphe
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.