SIST EN 206:2013/oprA1:2015
(Amendment)Concrete - Specification, performance, production and conformity
Concrete - Specification, performance, production and conformity
(1) This European Standard applies to concrete for structures cast in situ, precast structures, and structural precast products for buildings and civil engineering structures.
(2) The concrete under this European Standard can be:
- normal-weight, heavy-weight and light-weight;
- mixed on site, ready-mixed or produced in a plant for precast concrete products;
- compacted or self-compacting to retain no appreciable amount of entrapped air other than entrained air.
(3) This standard specifies requirements for:
- the constituents of concrete;
- the properties of fresh and hardened concrete and their verification;
- the limitations for concrete composition;
- the specification of concrete;
- the delivery of fresh concrete;
- the production control procedures;
- the conformity criteria and evaluation of conformity.
(4) Other European Standards for specific products e.g. precast products or for processes within the field of the scope of this standard may require or permit deviations.
(5) Additional or different requirements may be given for specific applications in other European Standards, for example:
concrete to be used in roads and other trafficked areas (e.g. concrete pavements according to EN 13877–1);
special technologies (e.g. sprayed concrete according to EN 14487).
(6) Supplementing requirements or different testing procedures may be specified for specific types of concrete and applications, for example:
concrete for massive structures (e.g. dams);
- dry mixed concrete;
- concrete with a Dmax of 4 mm or less (mortar);
- self-compacting concretes (SCC) containing lightweight or heavy-weight aggregates or fibres;
- concrete with open structure (e. g. pervious concrete for drainage).
(7) This standard does not apply to:
- aerated concrete;
- foamed concrete;
- concrete with density less than 800 kg/m3;
- refractory concrete.
(8) This standard does not cover health and safety requirements for the protection of workers during production and delivery of concrete.
Beton - Festlegung, Eigenschaften, Herstellung und Konformität
Béton - Spécification, performances, production et conformité
Beton - Specifikacija, lastnosti, proizvodnja in skladnost
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 206:2013/oprA1:2015
01-oktober-2015
Beton - Specifikacija, lastnosti, proizvodnja in skladnost
Concrete - Specification, performance, production and conformity
Beton - Festlegung, Eigenschaften, Herstellung und Konformität
Béton - Spécification, performances, production et conformité
Ta slovenski standard je istoveten z: EN 206:2013/prA1
ICS:
91.100.30 Beton in betonski izdelki Concrete and concrete
products
SIST EN 206:2013/oprA1:2015 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 206:2013/oprA1:2015
---------------------- Page: 2 ----------------------
SIST EN 206:2013/oprA1:2015
EUROPEAN STANDARD
DRAFT
EN 206:2013
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
August 2015
ICS 91.100.30
English Version
Concrete - Specification, performance, production and
conformity
Béton - Spécification, performances, production et Beton - Festlegung, Eigenschaften, Herstellung und
conformité Konformität
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 104.
This draft amendment A1, if approved, will modify the European Standard EN 206:2013. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has
the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 206:2013/prA1:2015 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 206:2013/oprA1:2015
EN 206:2013/prA1:2015 (E)
Contents Page
European foreword .3
1 Modification to Clause 2, Normative references .4
2 Modification to 5.1.3, Aggregates .4
3 Modification to 5.1.6, Additions (including mineral fillers and pigments) .4
4 Modification to 5.3.2, Limiting values for concrete composition .4
5 Modification to 5.4
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.