SIST EN 480-6:2024
(Main)Admixtures for concrete, mortar and grout - Test methods - Part 6: Infrared analysis
Admixtures for concrete, mortar and grout - Test methods - Part 6: Infrared analysis
This document specifies a method for identifying an admixture by infrared analysis (IR).
Zusatzmittel für Beton, Mörtel und Einpressmörtel - Prüfverfahren - Teil 6: Infrarot-Untersuchung
Dieses Dokument legt ein Verfahren zur Erkennung und Bestimmung eines Zusatzmittels durch Infrarot-Untersuchung (IR) fest.
Adjuvants pour béton, mortier et coulis - Méthodes d'essai - Partie 6 : Analyse infrarouge
Le présent document spécifie une méthode d'identification d'un adjuvant par analyse infrarouge (IR).
Kemijski dodatki za beton, malto in injekcijsko maso - Preskusne metode - 6. del: Infrardeča analiza
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-oktober-2024
Nadomešča:
SIST EN 480-6:2005
Kemijski dodatki za beton, malto in injekcijsko maso - Preskusne metode - 6. del:
Infrardeča analiza
Admixtures for concrete, mortar and grout - Test methods - Part 6: Infrared analysis
Zusatzmittel für Beton, Mörtel und Einpressmörtel - Prüfverfahren - Teil 6: Infrarot-
Untersuchung
Adjuvants pour béton, mortier et coulis - Méthodes d'essai - Partie 6 : Analyse infrarouge
Ta slovenski standard je istoveten z: EN 480-6:2024
ICS:
91.100.10 Cement. Mavec. Apno. Malta Cement. Gypsum. Lime.
Mortar
91.100.30 Beton in betonski izdelki Concrete and concrete
products
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN 480-6
EUROPEAN STANDARD
NORME EUROPÉENNE
August 2024
EUROPÄISCHE NORM
ICS 91.100.10; 91.100.30 Supersedes EN 480-6:2005
English Version
Admixtures for concrete, mortar and grout - Test methods
- Part 6: Infrared analysis
Adjuvants pour béton, mortier et coulis - Méthodes Zusatzmittel für Beton, Mörtel und Einpressmörtel -
d'essai - Partie 6 : Analyse infrarouge Prüfverfahren - Teil 6: Infrarot-Untersuchung
This European Standard was approved by CEN on 10 June 2024.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 480-6:2024 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Principle . 5
5 Apparatus . 5
6 Procedure . 5
6.1 Preparation of the dry material. 5
6.2 Infrared spectrophotometry. 6
7 Results . 6
8 Test report . 6
European foreword
This document (EN 480-6:2024) has been prepared by Technical Committee CEN/TC 104 “Concrete
and related products”, the secretariat of which is held by SN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by February 2025, and conflicting national standards
shall be withdrawn at the latest by February 2025.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 480-6:2005.
a) the ATR-technique (Attenuated Total Reflectance) was added as permissible sampling technique,
see 5.1;
b) editorial changes.
This document is part of the series EN 480 Admixtures for concrete, mortar and grout — Test methods,
which comprises the following:
— Part 1: Reference concrete and reference mor
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.