SIST EN 13598-1:2020
(Main)Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1: Specifications for ancillary fittings and shallow chambers
Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1: Specifications for ancillary fittings and shallow chambers
This document specifies the definitions and requirements for ancillary fittings and shallow chambers installed underground in non-pressure drainage and sewerage systems and manufactured from unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP), polypropylene with mineral modifier (PP-MD) or polyethylene (PE) intended for use for:
- non-pressure underground drainage and sewerage outside the building structure (application area code "U"), and
- non-pressure underground drainage and sewerage for both buried in ground within the building structure (application area code "D") and outside the building structure.
This is reflected in the marking of products by "U" and "UD".
It also covers the jointing of the ancillary fittings and shallow chambers to the pipework system.
The ancillary fittings covered by this standard are the following:
- sealed access fittings;
- rodding point covers;
- rodding tees;
- mechanical saddles.
Ancillary fittings according to this document are intended for use in pedestrian or vehicular traffic areas.
Ancillary fittings can be installed to a maximum depth of 6,0 m from ground level, with the exception of rodding point covers.
Shallow chambers according to this document are intended for use in private drains located in pedestrian areas above the ground water table, to a maximum depth of 2,0 m from ground level to the invert of the main channel. This document covers shallow chambers with flow profile bases, and their joints to the piping system.
NOTE 1 EN 124-series [1] and EN 1253-4 [2] covers may be used for shallow chambers.
NOTE 2 Manholes and inspection chambers are specified in EN 13598-2.
Ancillary fittings and shallow chambers complying with EN13598-1 comply with the general requirements given in EN 476.
Ancillary fittings and shallow chambers can be manufactured by various methods e.g. injection moulding, rotational moulding, spiral winding or fabricated from components made to other standards.
NOTE 3 Product complying with this document may be used with pipes, fittings and other components conforming to any of the plastics products standards listed in Clause 2, provided their dimension comply with the requirements for joint dimensions given in Clause 7 and to the requirements of Table 6.
NOTE 4 Products complying with this document can be installed in underground applications without additional static calculation.
Kunststoff-Rohrleitungssysteme für erdverlegte drucklose Abwasserkanäle und ‑leitungen - Weichmacherfreies Polyvinylchlorid (PVC-U), Polypropylen (PP) und Polyethylen (PE) - Teil 1: Anforderungen an Schächte mit geringer Einbautiefe und Zubehörteile
Dieses Dokument legt die Begriffe für und Anforderungen an erdverlegte Zubehörteile und Schächte mit geringer Einbautiefe fest, die in drucklose Abwasserkanäle und leitungen eingebaut werden und aus weichmacherfreiem Polyvinylchlorid (PVC-U), Polypropylen (PP), Polypropylen mit mineralischen Additiven (PP-MD) oder Polyethylen (PE) hergestellt sind, vorgesehen für die Verwendung in:
- erdverlegten drucklosen Abwasserkanälen und -leitungen außerhalb der Gebäudestruktur (Anwendungskennzeichen "U") sowie
- erdverlegten drucklosen Abwasserkanälen und leitungen, die sowohl innerhalb der Gebäudestruktur (Anwendungskennzeichen "D") als auch außerhalb der Gebäudestruktur unterirdisch verlegt werden.
Dies wird durch die Produktkennzeichnung "U" bzw. "UD" angezeigt.
Es behandelt auch den Anschluss der Zubehörteile und Schächte mit geringer Einbautiefe an das Rohrleitungssystem.
Diese Norm gilt für die folgenden Arten von Zubehörteilen:
- verschließbare Reinigungsrohre;
- Abdeckungen von Reinigungsöffnungen;
- Reinigungsformstücke;
- mechanische Sattelstücke.
Diesem Dokument entsprechende Zubehörteile sind für die Verwendung in Fußgänger oder in Straßenverkehrsbereichen vorgesehen.
Zubehörteile können in einer Tiefe von maximal 6,0 m ab Geländeoberkante eingebaut werden, mit Ausnahme von Abdeckungen von Reinigungsöffnungen.
Diesem Dokument entsprechende Schächte mit geringer Einbautiefe sind für die Verwendung in privaten Abwasserleitungen vorgesehen. Diese befinden sich in Fußgängerbereichen über dem Grundwasserspiegel bis zu einer maximalen Tiefe von 2,0 m, gemessen ab Geländeoberkante bis zur Sohle der Hauptleitung. Dieses Dokument behandelt Schächte mit geringer Einbautiefe sowie mit Schachtunterteilen mit Gerinneausbildung und ihre Rohrverbindungen zum Rohrleitungssystem.
ANMERKUNG 1 Abdeckungen nach der Normenreihe EN 124 und EN 1253-4 können für Schächte mit geringer Einbautiefe verwendet werden.
ANMERKUNG 2 Einsteigschächte und Kontrollschächte werden in EN 13598-2 festgelegt.
Zubehörteile und Schächte mit geringer Einbautiefe, die EN 13598-1 entsprechen, erfüllen die in EN 476 gegebenen allgemeinen Anforderungen.
Zubehörteile und Schächte mit geringer Einbautiefe können sowohl durch verschiedene Verfahren wie z. B. Spritzguss, Rotationsgießen oder spiralförmiges Wickeln, als auch handgefertigt aus Rohrleitungsteilen, die anderen Normen entsprechen, hergestellt werden.
ANMERKUNG 3 Produkte, die dem vorliegenden Dokument entsprechen, können mit Rohren, Formstücken und anderen Bauteilen verwendet werden, die sämtlichen in Abschnitt 2 aufgelisteten Normen für Kunststoffprodukte entsprechen, sofern sie die Anforderungen an die Maße der Rohrverbindungen nach Abschnitt 7 sowie die Anforderungen nach Tabelle 6 erfüllen.
ANMERKUNG 4 Produkte, die dem vorliegenden Dokuments entsprechen, können ohne zusätzliche statische Berechnung in erdverlegte Anwendungen eingebaut werden.
Systèmes de canalisations en plastique pour les branchements et les collecteurs d’assainissement enterrés sans pression - Poly(chlorure de vinyle) non plastifié (PVC-U), polypropylène (PP) et polyéthylène (PE) - Partie 1 : Spécifications relatives aux raccords auxiliaires et aux boîtes de branchement peu profondes
Le présent document spécifie les définitions et les exigences relatives aux raccords auxiliaires et boîtes peu profondes, enterrés et mis enoeuvre dans des systèmes de branchements et de collecteurs d’assainissement sans pression et fabriqués en poly(chlorure de vinyle) non plastifié (PVC-U), en polypropylène (PP), en polypropylène avec modificateurs minéraux (PP-MD) ou en polyéthylène (PE) destinés à être utilisés pour :
- les branchements et les collecteurs d’assainissement enterrés sans pression à l’extérieur de la structure du bâtiment (code de zone d’application « U ») ; et
- les branchements et les collecteurs d’assainissement enterrés sans pression aussi bien à l’intérieur de la structure du bâtiment (code de zone d’application « D ») qu’à l’extérieur de celle-ci.
Ceci est repéré au niveau du marquage des produits par « U » et « UD ».
Il couvre également l’assemblage des raccords auxiliaires et des boîteses peu profondes au système de canalisation.
Les raccords auxiliaires couverts par la présente norme sont les suivants :
- raccords d’accès scellés ;
- points de curage ;
- tés de curage ;
- selles mécaniques.
Les raccords auxiliaires selon le présent document sont destinés à être utilisés dans les zones de circulation de piétons ou de véhicules.
Les raccords auxiliaires peuvent être mis en oeuvre jusqu’à une profondeur maximale de 6,0 m en dessous du niveau du sol, à l’exception des points de curage.
Les boîtes peu profondes selon le présent document sont destinées à être utilisées dans les branchements privés situés dans les zones piétonnes au-dessus de la nappe phréatique, jusqu’à une profondeur maximale de 2,0 m en dessous du niveau du sol jusqu’au fil d’eau de la cunette principale. Le présent document traite des boîtes peu profondes avec des éléments de fond à profil d’écoulement, et de leurs assemblages au système de canalisation.
NOTE 1 Les tampons conformes à la série EN 124 et à l’EN 1253-4 peuvent être utilisés pour les boîtes peu profondes.
NOTE 2 Les regards et boîtes d’inspection et de branchement sont spécifiés dans l’EN 13598-2.
Les raccords auxiliaires et les boîtes peu profondes conformes à l’EN 13598-1 sont conformes aux exigences générales données dans l’EN 476.
Les raccords auxiliaires et les boîtes peu profondes peuvent être fabriqués selon différentes méthodes, par exemple moulage par injection, moulage par rotation, enroulement en spirale ou façonnage à partir de composants fabriqués selon d’autres normes.
NOTE 3 Les produits conformes au présent document peuvent être utilisés avec des tubes, des raccords et d’autres composants conformes à l’une des normes de produits plastiques référencées à l’Article 2, dans la mesure où leurs dimensions répondent aux exigences applicables aux dimensions d’assemblage données à l’Article 7 et aux exigences du Tableau 6.
NOTE 4 Les produits conformes au présent document peuvent être mis en oeuvre dans des applications enterrées sans calculs statiques supplémentaires.
Cevni sistemi iz polimernih materialov za odpadno vodo in kanalizacijo, ki delujejo po težnostnem principu in so položeni v zemljo - Nemehčan polivinilklorid (PVC-U), polipropilen (PP) in polietilen (PE) - 1. del: Specifikacije za pomožne fitinge in plitve revizijske jaške
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 13598-1:2020
01-junij-2020
Nadomešča:
SIST EN 13598-1:2011
Cevni sistemi iz polimernih materialov za odpadno vodo in kanalizacijo, ki delujejo
po težnostnem principu in so položeni v zemljo - Nemehčan polivinilklorid (PVC-
U), polipropilen (PP) in polietilen (PE) - 1. del: Specifikacije za pomožne fitinge in
plitve revizijske jaške
Plastics piping systems for non-pressure underground drainage and sewerage -
Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) -
Part 1: Specifications for ancillary fittings and shallow chambers
Kunststoff-Rohrleitungssysteme für erdverlegte drucklose Abwasserkanäle und
‑leitungen - Weichmacherfreies Polyvinylchlorid (PVC-U), Polypropylen (PP) und
Polyethylen (PE) - Teil 1: Anforderungen an Schächte mit geringer Einbautiefe und
Zubehörteile
Systèmes de canalisations en plastique pour les branchements et les collecteurs
d’assainissement enterrés sans pression - Poly(chlorure de vinyle) non plastifié (PVC-U),
polypropylène (PP) et polyéthylène (PE) - Partie 1 : Spécifications relatives aux raccords
auxiliaires et aux boîtes de branchement peu profondes
Ta slovenski standard je istoveten z: EN 13598-1:2020
ICS:
23.040.05 Cevovodi za zunanje Pipeline and its parts for
sisteme za odpadno vodo in external sewage systems
njihovi deli
93.030 Zunanji sistemi za odpadno External sewage systems
vodo
SIST EN 13598-1:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 13598-1:2020
---------------------- Page: 2 ----------------------
SIST EN 13598-1:2020
EN 13598-1
EUROPEAN STANDARD
NORME EUROPÉENNE
May 2020
EUROPÄISCHE NORM
ICS 23.040.05; 23.040.20; 93.030 Supersedes EN 13598-1:2010
English Version
Plastics piping systems for non-pressure underground
drainage and sewerage - Unplasticized poly(vinyl chloride)
(PVC-U), polypropylene (PP) and polyethylene (PE) - Part
1: Specifications for ancillary fittings and shallow
chambers
Systèmes de canalisations en plastique pour les Kunststoff-Rohrleitungssysteme für erdverlegte
branchements et les collecteurs d'assainissement drucklose Abwasserkanäle und -leitungen -
enterrés sans pression - Poly(chlorure de vinyle) non Weichmacherfreies Polyvinylchlorid (PVC-U),
plastifié (PVC-U), polypropylène (PP) et polyéthylène Polypropylen (PP) und Polyethylen (PE) - Teil 1:
(PE) - Partie 1: Spécifications relatives aux raccords Anforderungen an Schächte und Zubehörteile und
auxiliaires et aux boîtes d'inspection de branchement flache Kammern
peu profondes
This European Standard was approved by CEN on 14 March 2020.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13598-1:2020 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 13598-1:2020
EN 13598-1:2020 (E)
Contents Page
European foreword . 4
1 Scope . 6
2 Normative references . 7
3 Terms and definitions . 9
4 Symbols and abbreviations . 12
4.1 Symbols . 12
4.2 Abbreviations . 12
5 Material . 12
5.1 Ancillary fittings . 12
5.2 Shallow chambers . 13
5.3 Sealing ring retaining components . 13
6 General characteristics . 13
6.1 Appearance . 13
6.2 Colour . 13
6.3 Assemblies . 13
7 Geometrical characteristics . 13
7.1 General . 13
7.2 Dimensions . 13
7.2.1 General . 13
7.2.2 Design lengths . 14
7.2.3 Dimensions of ancillary fittings . 14
7.2.4 Dimensions of shallow chambers . 14
7.3 Additional requirements for sealed access fittings . 14
8 Mechanical characteristics . 14
9 Physical characteristics . 16
9.1 Injection moulded ancillary fittings . 16
9.2 Fabricated ancillary fittings . 16
10 Performance requirements . 17
11 Sealing rings . 19
12 Adhesives . 19
13 Marking and additional documentation . 19
13.1 General . 19
13.2 Minimum required marking, sealed access fittings and rodding tees . 19
13.3 Minimum required marking, mechanical saddles . 20
13.4 Minimum required marking, shallow chambers . 20
13.5 Additional documentation, shallow chambers . 21
13.6 Additional documentation, mechanical saddles . 21
Annex A (normative) Utilization of non-virgin material for shallow chambers . 22
A.1 Utilization of non-virgin materials . 22
A.2 Material characteristics . 24
2
---------------------- Page: 4 ----------------------
SIST EN 13598-1:2020
EN 13598-1:2020 (E)
Annex B (normative) Test methods for mechanical saddles . 26
B.1 General . 26
B.2 Test equipment . 26
B.3 Procedures . 27
B.3.1 Resistance to vertical load – pipe stop test . 27
B.3.2 Mechanical strength . 28
B.3.3 Tightness under deformation . 29
Annex C (normative) Resistance to vertical loading of shallow chambers . 31
Bibliography . 32
3
---------------------- Page: 5 ----------------------
SIST EN 13598-1:2020
EN 13598-1:2020 (E)
European foreword
This document (EN 13598-1:2020) has been prepared by Technical Committee CEN/TC 155 “Plastics
piping systems and ducting systems”, the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by November 2020, and conflicting national standards shall
be withdrawn at the latest by November 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 13598-1:2010.
Compared to the previous version, the main changes are listed below:
1) test methods have been updated to the latest EN ISO standards where applicable;
2) the scope has been amended to clarify the products covered in this part and avoid confusion with the
scope of part 2;
3) terms and definitions have been updated and also now include the product diagrams;
4) dimensional requirements have been updated and clarified;
5) the mechanical characteristics tables have been updated;
6) Annex A has been updated with requirements for the utilization of non-virgin materials for shallow
chambers.
This document is part of a System Standard for plastics piping systems of a particular material for a
specified application. There are a number of such System Standards.
System Standards are based on the results of the work being undertaken in ISO/TC 138 “Plastics pipes,
fittings and valves for the transport of fluids”, which is a Technical Committee of the International
Organization for Standardization (ISO).
They are supported by separate standards on test methods, to which references are made throughout the
System Standard.
The System Standards are consistent with general standards on functional requirements and on
recommended practice for installation.
EN 13598 consists of the following parts under the general title Plastics piping systems for non-pressure
underground drainage and sewerage — Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and
polyethylene (PE):
— Part 1: Specifications for ancillary fittings and shallow chambers (this document);
— Part 2: Specifications for manholes and inspection chambers (under revision);
— Part 3: Guidance for assessment of conformity (CEN/TS under revision).
4
---------------------- Page: 6 ----------------------
SIST EN 13598-1:2020
EN 13598-1:2020 (E)
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United
Kingdom.
5
---------------------- Page: 7 ----------------------
SIST EN 13598-1:2020
EN 13598-1:2020 (E)
1 Scope
This document specifies the definitions and requirements for ancillary fittings and shallow chambers
installed underground in non-pressure drainage and sewerage systems and manufactured from
unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP), polypropylene with mineral modifier
(PP-MD) or polyethylene (PE) intended for use for:
— non-pressure underground drainage and sewerage outside the building structure (application area
code “U”), and
— non-pressure underground drainage and sewerage for both buried in ground within the building
structure (application area code “D”) and outside the building structure.
This is reflected in the marking of products by “U” and “UD”.
It also covers the jointing of the ancillary fittings and shallow chambers to the pipework system.
The ancillary fittings covered by this standard are the following:
— sealed access fittings;
— rodding point covers;
— rodding tees;
— mechanical saddles.
Ancillary fittings according to this document are intended for use in pedestrian areas, except rodding tees
and mechanical saddles which can also be used in vehicular trafficked areas.
NOTE 1 Pedestrian areas are as defined in EN 124-1.
Ancillary fittings can be installed to a maximum depth of 6,0 m from ground level, with the exception of
rodding point covers.
Shallow chambers according to this document are intended for use in private drains located in pedestrian
areas above the ground water table, to a maximum depth of 2,0 m from ground level to the invert of the
main channel. This document covers shallow chambers with flow profile bases, and their joints to the
piping system.
NOTE 2 Manholes and inspection chambers are specified in EN 13598-2 [1].
Ancillary fittings and shallow chambers complying with this document also comply with the general
requirements given in EN 476.
Ancillary fittings and shallow chambers can be manufactured by various methods e.g. injection moulding,
rotational moulding, spiral winding or fabricated from components made to other standards.
NOTE 3 Products complying with this document can be used with pipes, fittings and other components
conforming to any of the plastics products standards listed in Clause 2, providing their dimensions are compatible.
NOTE 4 Products complying with this document can be installed in underground applications without additional
static calculation.
NOTE 5 Ancillary fittings and shallow chambers can be subject to national safety regulations and / or local
provisions.
6
---------------------- Page: 8 ----------------------
SIST EN 13598-1:2020
EN 13598-1:2020 (E)
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 124 (series), Gully tops and manhole tops for vehicular and pedestrian areas
EN 295-3:2012, Vitrified clay pipe systems for drains and sewers - Part 3: Test methods
EN 476:2011, General requirements for components used in drains and sewers
EN 681-1, Elastomeric seals - Materials requirements for pipe joint seals used in water and drainage
applications - Part 1: Vulcanized rubber
EN 681-2, Elastomeric Seals — Materials requirements for pipe joint seals used in water and drainage
applications — Part 2: Thermoplastic elastomers
EN 681-3, Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage
applications — Part 3: Cellular materials of vulcanized rubber
EN 681-4, Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage
applications — Part 4: Cast polyurethane sealing elements
EN 1253-2:2015, Gullies for buildings - Part 2: Roof drains and floor gullies without trap
EN 1401-1, Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized
poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system
EN 1852-1, Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene
(PP) - Part 1: Specifications for pipes, fittings and the system
EN 1905, Plastics piping systems - Unplasticized poly(vinyl chloride) (PVC-U) pipes, fittings and material -
Method for assessment of the PVC content based on total chlorine content
EN 12099, Plastics piping systems - Polyethylene piping materials and components - Determination of
volatile content
EN 12666-1, Plastics piping systems for non-pressure underground drainage and sewerage — Polyethylene
(PE) — Part 1: Specifications for pipes, fittings and the system
EN 13476-1, Plastics piping systems for non-pressure underground drainage and sewerage - Structured-
wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE)
- Part 1:General requirements and performance characteristics
EN 13476-2, Plastics piping systems for non-pressure underground drainage and sewerage - Structured-
wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE)
- Part 2: Specifications for pipes and fittings with smooth internal and external surface and the system, Type
A
EN 13476-3, Plastics piping systems for non-pressure underground drainage and sewerage - Structured-
wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE)
- Part 3: Specifications for pipes and fittings with smooth internal and profiled external surface and the
system, Type B
7
---------------------- Page: 9 ----------------------
SIST EN 13598-1:2020
EN 13598-1:2020 (E)
EN 14680, Adhesives for non-pressure thermoplastics piping systems - Specifications
EN 14814, Adhesives for thermoplastic piping systems for fluids under pressure - Specifications
EN 14758-1, Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene
with mineral modifiers (PP-MD) - Part 1: Specifications for pipes, fittings and the system
EN ISO 472, Plastics - Vocabulary (ISO 472:2013)
EN ISO 1043-1, Plastics - Symbols and abbreviated terms - Part 1: Basic polymers and their special
characteristics (ISO 1043-1:2011)
EN ISO 1133-1, Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR)
of thermoplastics - Part 1: Standard method (ISO 1133-1:2011)
EN ISO 1183-1, Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion
method, liquid pycnometer method and titration method (ISO 1183-1:2019, Corrected version 2019-05)
EN ISO 1183-2, Plastics - Methods for determining the density of non-cellular plastics - Part 2: Density
gradient column method (ISO 1183-2:2019)
EN ISO 2507-1, Thermoplastics pipes and fittings - Vicat softening temperature - Part 1: General test
method (ISO 2507-1:1995)
EN ISO 3126, Plastics piping systems - Plastics components - Determination of dimensions (ISO 3126:2005)
EN ISO 3451-1, Plastics - Determination of ash - Part 1: General methods (ISO 3451-1:2019)
EN ISO 3451-5, Plastics - Determination of ash - Part 5: Poly(vinyl chloride) (ISO 3451-5:2002)
EN ISO 11357-6, Plastics - Differential scanning calorimetry (DSC) - Part 6: Determination of oxidation
induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT) (ISO 11357-6:2018)
EN ISO 13254, Thermoplastics piping systems for non-pressure applications - Test method for
watertightness (ISO 13254:2010)
EN ISO 13257:2017, Thermoplastics piping systems for non-pressure applications — Test method for
resistance to elevated temperature cycling (ISO 13257:2010)
EN ISO 13259, Thermoplastics piping systems for underground non-pressure applications - Test method for
leaktightness of elastomeric sealing ring type joints (ISO 13259:2018)
EN ISO 13263, Thermoplastics piping systems for non-pressure underground drainage and sewerage -
Thermoplastics fittings - Test method for impact strength (ISO 13263:2010)
EN ISO 13264, Thermoplastics piping systems for non-pressure underground drainage and sewerage -
Thermoplastics fittings - Test method for mechanical strength or flexibility of fabricated fittings (ISO
13264:2010)
ISO 13268, Thermoplastics piping systems for non-pressure underground drainage and sewerage —
Thermoplastics shafts or risers for inspection chambers and manholes — Determination of ring stiffness
8
---------------------- Page: 10 ----------------------
SIST EN 13598-1:2020
EN 13598-1:2020 (E)
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN ISO 472, EN ISO 1043-1 and the
following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at http://www.electropedia.org/
— ISO Online browsing platform: available at https://www.iso.org/obp
3.1
private drain
drainage (discharge) system which is not a part of the public drain or sewer
3.2
sealed access fitting
fitting that permits entry into the system for rodding or inspection and that has a sealed cover
Note 1 to entry: Figure 1 shows examples of sealed access fittings, other designs are possible.
Note 2 to entry: Sealed access fittings are typically buried to a depth of 2m or installed up to 6m when installed
within a chamber
3.3
rodding point cover
fitting installed at ground level with a removable cover that permits the introduction of equipment for
inspection and the clearance of blockages
Note 1 to entry: Figure 2 shows examples of rodding point covers, other designs are possible.
3.4
rodding tee
fitting installed in a drainage or sewerage system that connects to a rodding point at ground level that
permits the introduction of equipment for the clearance of blockages, and also equipment for the
inspection of the connecting pipe work in one or more directions
Note 1 to entry: Figure 3 shows an example of a rodding tee, other designs are possible.
3.5
mechanical saddle
fitting that enables a branch connection to be made to buried drainage/sewerage systems of larger
diameter by cutting a hole in the larger pipe and is retained in position by mechanical means
Note 1 to entry: Figure 4 shows examples of mechanical saddles, other designs are possible.
Note 2 to entry: Preferred nominal angles for mechanical saddle branches are 45° and 90°.
3.6
shallow chamber
fitting installed to a maximum depth of 2,0 m from ground level to the invert of the main channel that
permits the introduction of equipment for the clearance of blockages, cleaning and inspection from
surface level, but does not provide access for personnel and which terminates at ground level with a riser
shaft of DN/ID 180 minimum and DN/ID of less than 800
Note 1 to entry: See also EN 476 for non-circular chambers.
Note 2 to entry: Figure 5 shows examples of shallow chambers, other designs are possible.
9
---------------------- Page: 11 ----------------------
SIST EN 13598-1:2020
EN 13598-1:2020 (E)
3.7
base
bottom part of a shallow chamber, including integrally formed channels with benching as appropriate
Note 1 to entry: In case of a one-piece shallow chamber, for testing purposes the base component ends at a
distance of minimum 300 mm measured from the top of the main channel. Above 300 mm the section should be
considered as a riser and tested accordingly.
Note 2 to entry: The benching is the transition between the formed channel and the inside wall of the base.
3.8
riser
component which is connected onto a base and which defines the nominal size of the shallow chamber
Note 1 to entry: The riser can be supplied either as one or more separate items, for site jointing to the base, or
integrated with the base.
Note 2 to entry: In case of a one-piece shallow chamber, for testing purposes the riser component starts at a
distance of minimum 300 mm measured from the top of the main channel. Below 300 mm the section should be
considered as a base and tested accordingly.
3.9
fabricated fitting
fitting produced from pipe and/or from injection-moulded fittings by thermoforming, adhesive joint or
welding
3.10
virgin material
material in a form such as granules or powder that has not been subjected to use or processing other than
that required for its manufacture and to which no reprocessed or recycled material has been added
Note 1 to entry: It is understood that the addition of additives such as stabilizers and pigments is still resulting
into a virgin material.
3.11
own reprocessed material
material prepared from unused products, including trimmings from the production, that will be
reprocessed in a manufacturer’s plant after having been previously processed by the same manufacturer
3.12
recycled material
material prepared from used thermoplastic products which have been cleaned and crushed or ground
3.13
agreed specification
specification of the relevant material characteristics agreed between the supplier of the non-virgin
material and the manufacturer
10
---------------------- Page: 12 ----------------------
SIST EN 13598-1:2020
EN 13598-1:2020 (E)
Figure 1 — Examples of sealed access fittings
Figure 2 — Examples of rodding point covers
Figure 3 — Example of a rodding tee
Figure 4 — Examples of mechanical saddles
Figure 5 — Examples of shallow chambers
11
---------------------- Page: 13 ----------------------
SIST EN 13598-1:2020
EN 13598-1:2020 (E)
4 Symbols and abbreviations
4.1 Symbols
For the purposes of this document, the following symbols apply.
A length of engagement
d mean outside diameter
em
d nominal outside diameter
n
d mean inside diameter of socket
sm
e minimum wall thickness
min
e2 wall thickness of a socket
e wall thickness in the groove area
3
L length of spigot
1
y determined value when tested
4.2 Abbreviations
For the purposes of this document, the following abbreviations apply.
DN nominal size
DN/ID nominal size, inside diameter related
DN/OD nominal size, outside diameter related
DSC differential scanning calorimetry
IR infrared
MFR melt mass-flow rate
NA not applicable
OIT oxidation induction time
PE polyethylene
PP polypropylene
PP-MD polypropylene modified with minerals
PVC-U unplasticized poly(vinyl chloride)
SDR standard dimension ratio
SN nominal ring stiffness
5 Material
5.1 Ancillary fittings
The material shall conform to EN 1401-1, EN 1852-1, EN 12666-1, EN 13476-1, EN 13476-3 or
EN 147
...
SLOVENSKI STANDARD
oSIST prEN 13598-1:2019
01-februar-2019
&HYQLVLVWHPLL]SROLPHUQLKPDWHULDORY]DRGSDGQRYRGRLQNDQDOL]DFLMRNLGHOXMHMR
SRWHåQRVWQHPSULQFLSXLQVRSRORåHQLY]HPOMR1HPHKþDQSROLYLQLONORULG 39&
8 SROLSURSLOHQ 33 LQSROLHWLOHQ 3( GHO 6SHFLILNDFLMH]DSRPRåQHILWLQJHLQ
SOLWYHUHYL]LMVNHMDãNH
Plastics piping systems for non-pressure underground drainage and sewerage -
Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) -
Part 1: Specifications for ancillary fittings and shallow chambers
.XQVWVWRII5RKUOHLWXQJVV\VWHPHIUHUGYHUOHJWHGUXFNORVH$EZDVVHUNDQlOH
XQG"OHLWXQJHQ:HLFKPDFKHUIUHLHV3RO\YLQ\OFKORULG 39&8 3RO\SURS\OHQ 33 XQG
3RO\HWK\OHQ 3( 7HLO $QIRUGHUXQJHQDQ6FKlFKWHPLWJHULQJHU(LQEDXWLHIHXQG
=XEHK|UWHLOH
Systèmes de canalisations en plastique pour les branchements et les collecteurs
d’assainissement enterrés sans pression - Poly(chlorure de vinyle) non plastifié (PVC-U),
polypropylène (PP) et polyéthylène (PE) - Partie 1 : Spécifications relatives aux raccords
auxiliaires et aux boîtes de branchement peu profondes
Ta slovenski standard je istoveten z: prEN 13598-1
ICS:
23.040.05 Cevovodi za zunanje Pipeline and its parts for
sisteme za odpadno vodo in external sewage systems
njihovi deli
93.030 Zunanji sistemi za odpadno External sewage systems
vodo
oSIST prEN 13598-1:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 13598-1:2019
---------------------- Page: 2 ----------------------
oSIST prEN 13598-1:2019
DRAFT
EUROPEAN STANDARD
prEN 13598-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2018
ICS 23.040.05; 23.040.20; 93.030 Will supersede EN 13598-1:2010
English Version
Plastics piping systems for non-pressure underground
drainage and sewerage - Unplasticized poly(vinyl chloride)
(PVC-U), polypropylene (PP) and polyethylene (PE) - Part
1: Specifications for ancillary fittings and shallow
chambers
Systèmes de canalisations en plastique pour les Kunststoff-Rohrleitungssysteme für erdverlegte
branchements et les collecteurs d'assainissement drucklose Abwasserkanäle und -leitungen -
enterrés sans pression - Poly(chlorure de vinyle) non Weichmacherfreies Polyvinylchlorid (PVC-U),
plastifié (PVC-U), polypropylène (PP) et polyéthylène Polypropylen (PP) und Polyethylen (PE) - Teil 1:
(PE) - Partie 1 : Spécifications relatives aux raccords Anforderungen an Schächte mit geringer Einbautiefe
auxiliaires et aux boîtes de branchement peu und Zubehörteile
profondes
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 155.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 13598-1:2018 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 13598-1:2019
prEN 13598-1:2018 (E)
Contents Page
European foreword . 4
1 Scope . 5
2 Normative references . 6
3 Terms and definitions . 8
4 Symbols and abbreviations . 12
4.1 Symbols . 12
4.2 Abbreviations . 13
5 Material . 13
5.1 General . 13
5.2 Sealing ring retaining components . 13
6 General characteristics . 13
6.1 Appearance . 13
6.2 Colour . 13
6.3 Assemblies . 13
7 Geometrical characteristics . 14
7.1 General . 14
7.2 Dimensions . 14
7.2.1 General . 14
7.2.2 Design lengths . 14
7.2.3 Dimensions of ancillary fittings . 14
7.2.4 Dimensions of shallow chambers . 14
7.3 Additional requirements for sealed access fittings . 14
8 Mechanical characteristics . 15
9 Physical characteristics . 17
9.1 Injection moulded ancillary fittings . 17
9.2 Factory fabricated ancillary fittings . 17
10 Performance requirements . 17
11 Sealing rings . 19
12 Adhesives . 19
13 Marking . 19
13.1 General . 19
13.2 Minimum required marking, sealed access fittings and rodding tees . 19
13.3 Minimum required marking, mechanical saddles . 19
13.4 Minimum required marking, shallow chambers . 19
Annex A (normative) Utilization of non-virgin material for shallow chambers . 22
A.1 Utilization of non-virgin materials . 22
A.2 Material characteristics . 24
Annex B (normative) Test methods for mechanical saddles . 26
B.1 General . 26
2
---------------------- Page: 4 ----------------------
oSIST prEN 13598-1:2019
prEN 13598-1:2018 (E)
B.2 Test equipment . 26
B.3 Procedures . 27
B.3.1 Resistance to vertical load – pipe stop test . 27
B.3.2 Mechanical strength . 27
B.3.3 Tightness under deformation . 28
Bibliography . 30
3
---------------------- Page: 5 ----------------------
oSIST prEN 13598-1:2019
prEN 13598-1:2018 (E)
European foreword
This document (prEN 13598-1:2018) has been prepared by Technical Committee CEN/TC 155 “Plastics
piping systems and ducting systems”, the secretariat of which is held by NEN.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 13598-1:2010.
Compared to the previous version, the main changes are listed below:
1) test methods have been updated to the latest EN ISO standards where applicable;
2) the scope has been amended to clarify the products covered in this part and avoid confusion with the
scope of part 2;
3) terms and definitions have been updated and also now include the product diagrams;
4) dimensional requirements have been updated and clarified;
5) the mechanical characteristics tables have been updated;
6) Annex A has been updated with requirements for the utilization of non-virgin materials for shallow
chambers.
This document is part of a System Standard for plastics piping systems of a particular material for a
specified application. There are a number of such System Standards.
System Standards are based on the results of the work being undertaken in ISO/TC 138 “Plastics pipes,
fittings and valves for the transport of fluids”, which is a Technical Committee of the International
Organization for Standardization (ISO).
They are supported by separate standards on test methods, to which references are made throughout the
System Standard.
The System Standards are consistent with general standards on functional requirements and on
recommended practice for installation.
EN 13598 consists of the following parts under the general title Plastics piping systems for non-pressure
underground drainage and sewerage — Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and
polyethylene (PE):
— Part 1: Specifications for ancillary fittings and shallow chambers (this document);
— Part 2: Specifications for manholes and inspection chambers (under revision);
— Part 3: Guidance for assessment of conformity (CEN/TS under revision).
4
---------------------- Page: 6 ----------------------
oSIST prEN 13598-1:2019
prEN 13598-1:2018 (E)
1 Scope
This document specifies the definitions and requirements for ancillary fittings and shallow chambers
installed underground in non-pressure drainage and sewerage systems and manufactured from
unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP), polypropylene with mineral modifier
(PP-MD) or polyethylene (PE) intended for use for:
— non-pressure underground drainage and sewerage outside the building structure (application area
code “U”), and
— non-pressure underground drainage and sewerage for both buried in ground within the building
structure (application area code “D”) and outside the building structure.
This is reflected in the marking of products by “U” and “UD”.
It also covers the jointing of the ancillary fittings and shallow chambers to the pipework system.
The ancillary fittings covered by this standard are the following:
— sealed access fittings;
— rodding point covers;
— rodding tees;
— mechanical saddles.
Ancillary fittings according to this document are intended for use in pedestrian or vehicular traffic areas.
Ancillary fittings can be installed to a maximum depth of 6,0 m from ground level, with the exception of
rodding point covers.
Shallow chambers according to this document are intended for use in private drains located in pedestrian
areas above the ground water table, to a maximum depth of 2,0 m from ground level to the invert of the
main channel. This document covers shallow chambers with flow profile bases, and their joints to the
piping system.
NOTE 1 EN 124 series and EN 1253-4 covers can be used for shallow chambers.
NOTE 2 Manholes and inspection chambers are specified in EN 13598-2.
Ancillary fittings and shallow chambers complying with EN13598-1 comply with the general
requirements given in EN 476.
Ancillary fittings and shallow chambers can be manufactured by various methods e.g. injection moulding,
rotational moulding, spiral winding or fabricated from components made to other standards.
NOTE 3 Products complying with this document can be used with pipes, fittings and other components
conforming to any of the plastics products standards listed in Clause 2, provided their dimension comply with the
requirements for joint dimensions given in Clause 7 and to the requirements of Table 6.
NOTE 4 Products complying with this document can be installed in underground applications without additional
static calculation.
5
---------------------- Page: 7 ----------------------
oSIST prEN 13598-1:2019
prEN 13598-1:2018 (E)
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 124 (series), Gully tops and manhole tops for vehicular and pedestrian areas
EN 295-3:2012, Vitrified clay pipe systems for drains and sewers — Part 3: Test methods
EN 476:2011, General requirements for components used in drains and sewers
EN 681-1, Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage
applications — Part 1: Vulcanized rubber
EN 681-2, Elastomeric Seals — Materials requirements for pipe joint seals used in water and drainage
applications — Part 2: Thermoplastic elastomers
EN 681-3, Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage
applications — Part 3: Cellular materials of vulcanized rubber
EN 681-4, Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage
applications — Part 4: Cast polyurethane sealing elements
EN 1253 (series), Gullies for buildings
EN 1401-1, Plastics piping systems for non-pressure underground drainage and sewerage — Unplasticized
poly(vinyl chloride) (PVC-U) — Part 1: Specifications for pipes, fittings and the system
EN 1852-1, Plastics piping systems for non-pressure underground drainage and sewerage — Polypropylene
(PP) — Part 1: Specifications for pipes, fittings and the system
EN 1905, Plastics piping systems — Unplasticized poly(vinyl chloride) (PVC-U) pipes, fittings and material
— Method for assessment of the PVC content based on total chlorine content
EN 12099, Plastics piping systems — Polyethylene piping materials and components — Determination of
volatile content
EN 12666-1, Plastics piping systems for non-pressure underground drainage and sewerage — Polyethylene
(PE) — Part 1: Specifications for pipes, fittings and the system
EN 13476-1, Plastics piping systems for non-pressure underground drainage and sewerage — Structured-
wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE)
— Part 1:General requirements and performance characteristics
EN 13476-2, Plastics piping systems for non-pressure underground drainage and sewerage — Structured-
wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE)
— Part 2: Specifications for pipes and fittings with smooth internal and external surface and the system,
Type A
EN 13476-3, Plastics piping systems for non-pressure underground drainage and sewerage — Structured-
wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE)
— Part 3: Specifications for pipes and fittings with smooth internal and profiled external surface and the
system, Type B
6
---------------------- Page: 8 ----------------------
oSIST prEN 13598-1:2019
prEN 13598-1:2018 (E)
prEN 13598-2, Plastics piping systems for non-pressure underground drainage and sewerage —
Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) — Part 2:
Specifications for manholes and inspection chambers
EN 14680, Adhesives for non-pressure thermoplastics piping systems — Specifications
EN 14814, Adhesives for thermoplastic piping systems for fluids under pressure — Specifications
EN 14758-1, Plastics piping systems for non-pressure underground drainage and sewerage —
Polypropylene with mineral modifiers (PP-MD) — Part 1: Specifications for pipes, fittings and the system
EN 15346:2014, Plastics — Recycled plastics — Characterization of poly(vinyl chloride) (PVC) recyclates
EN ISO 472, Plastics — Vocabulary
EN ISO 1043-1, Plastics - Symbols and abbreviated terms — Part 1: Basic polymers and their special
characteristics (ISO 1043-1)
EN ISO 1133-1, Plastics — Determination of the melt mass-flow rate (MFR) and melt volume-flow rate
(MVR) of thermoplastics — Part 1: Standard method (ISO 1133-1)
EN ISO 1183-1, Plastics — Methods for determining the density of non-cellular plastics — Part 1: Immersion
method, liquid pyknometer method and titration method (ISO 1183-1)
EN ISO 1183-2, Plastics - Methods for determining the density of non-cellular plastics — Part 2: Density
gradient column method (ISO 1183-2)
EN ISO 2507-1, Thermoplastics pipes and fittings — Vicat softening temperature — Part 1: General test
method (ISO 2507-1)
EN ISO 3126, Plastics piping systems — Plastics components — Determination of dimensions (ISO 3126)
EN ISO 3451-1, Plastics — Determination of ash — Part 1: General methods (ISO 3451-1)
EN ISO 3451-5, Plastics — Determination of ash — Part 5: Poly(vinyl chloride) (ISO 3451-5)
EN ISO 11357-6, Plastics — Differential scanning calorimetry (DSC) — Part 6: Determination of oxidation
induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT) (ISO 11357-6)
EN ISO 13229, Thermoplastics piping systems for non-pressure applications — Unplasticized poly(vinyl
chloride) (PVC-U) pipes and fittings — Determination of the viscosity number and K-value (ISO 13229:2010)
EN ISO 13254, Thermoplastics piping systems for non-pressure applications — Test method for
watertightness (ISO 13254)
EN ISO 13257:2017, Thermoplastics piping systems for non-pressure applications — Test method for
resistance to elevated temperature cycling (ISO 13257:2010)
EN ISO 13259, Thermoplastics piping systems for underground non-pressure applications — Test method
for leaktightness of elastomeric sealing ring type joints (ISO 13259)
EN ISO 13263, Thermoplastics piping systems for non-pressure underground drainage and sewerage —
Thermoplastics fittings — Test method for impact strength (ISO 13263)
7
---------------------- Page: 9 ----------------------
oSIST prEN 13598-1:2019
prEN 13598-1:2018 (E)
EN ISO 13264, Thermoplastics piping systems for non-pressure underground drainage and sewerage —
Thermoplastics fittings — Test method for mechanical strength or flexibility of fabricated fittings (ISO
13264)
prEN ISO 13268, Thermoplastics piping systems for non-pressure underground drainage and sewerage —
Thermoplastics shafts or risers for inspection chambers and manholes — Determination of ring stiffness
(ISO 13268)
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN ISO 472, EN ISO 1043-1 and the
following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at http://www.electropedia.org/
— ISO Online browsing platform: available at http://www.iso.org/obp
3.1
private drains
drainage system within the total ground area of a property not in municipal ownership
3.2
sealed access fittings
fitting that permits entry into the system for rodding or inspection and that has a sealed cover
Note 1 to entry: Figure 1 shows examples of sealed access fittings, other designs are possible which can be
required to conform to national requirements and/or local practice.
3.3
rodding point cover
fitting installed at ground level with a removable cover that permits the introduction of equipment for
inspection and the clearance of blockages
Note 1 to entry: Figure 2 shows examples of rodding point covers, other designs are possible which can be
required to conform to national requirements and/or local practice.
3.4
rodding tee
fitting installed in a drainage or sewerage system that connects to a rodding point at ground level that
permits the introduction of equipment for the clearance of blockages, and also equipment for the
inspection of the connecting pipe work in one or more directions
Note 1 to entry: Rodding tees may be subject to national regulations and / or local provisions.
Note 2 to entry: Figure 3 shows an example of a rodding tee, other designs are possible which can be required to
conform to national requirements and/or local practice.
3.5
mechanical saddle
fitting that enables a branch connection to be made to buried drainage/sewerage systems of larger
diameter by cutting a hole in the larger pipe and is retained in position by mechanical means
Note 1 to entry: Figure 4 shows examples of mechanical saddles, other designs are possible which can be
required to conform to national requirements and/or local practice.
8
---------------------- Page: 10 ----------------------
oSIST prEN 13598-1:2019
prEN 13598-1:2018 (E)
Note 2 to entry: Preferred nominal angles for mechanical saddle branches are 45° and 90°.
3.6
shallow chamber
fitting that permits the introduction of cleaning and inspection equipment from surface level, but does
not provide access for personnel and which terminates at ground level with a riser shaft of 180 mm
minimum and inner diameter of less than 800 mm
Note 1 to entry: See also EN 476 for non-circular chambers.
Note 2 to entry: Shallow chambers are subject to national safety regulations and / or local provisions.
Note 3 to entry: Figure 5 shows examples of shallow chambers, other designs are possible which can be required
to conform to national requirements and/or local practice.
3.7
base
bottom part of a shallow chamber, allowing direct connection to buried drain and including integrally
formed channels with benching as appropriate
Note 1 to entry: In case of a one-piece shallow chamber, for testing purposes the base component ends at a
distance of 300 mm measured from the top of the main channel. Above 300 mm the section should be considered
as a riser and tested accordingly.
3.8
fabricated fitting
fitting produced from pipe and/or from injection-moulded fittings by thermoforming, adhesive
joint or welding
Note 1 to entry: Fabricated fittings need an additional fabrication step.
3.9
virgin material
material in a form such as granules or powder that has not been subjected to use or processing other than
that required for its manufacture and to which no reprocessed or recycled material has been added
Note1 to entry: It is understood that the addition of additives such as stabilizers and pigments is still resulting
into a virgin material
3.10
own reprocessed material
material prepared from unused products, including trimmings from the production, that will be
reprocessed in a manufacturer’s plant after having been previously processed by the same manufacturer
3.11
recycled material
material prepared from used thermoplastic products which have been cleaned and crushed or ground
3.12
agreed specification
specification of the relevant material characteristics agreed between the supplier of the non-virgin
material and the manufacturer
9
---------------------- Page: 11 ----------------------
oSIST prEN 13598-1:2019
prEN 13598-1:2018 (E)
Figure 1 — Examples of sealed access fittings
Figure 2 — Examples of rodding point covers
10
---------------------- Page: 12 ----------------------
oSIST prEN 13598-1:2019
prEN 13598-1:2018 (E)
Figure 3 — Example of a rodding tee
Figure 4 — Examples of mechanical saddles
11
---------------------- Page: 13 ----------------------
oSIST prEN 13598-1:2019
prEN 13598-1:2018 (E)
Figure 5 — Examples of shallow chambers
4 Symbols and abbreviations
For the purposes of this document, the following symbols and abbreviations apply.
4.1 Symbols
A length of engagement
d outside diameter
e
dem mean outside diameter
d nominal outside diameter
n
d mean inside diameter of socket
sm
e minimum wall thickness
min
e wall thickness of a socket
2
e wall thickness in the groove area
3
L length of spigot
1
12
---------------------- Page: 14 ----------------------
oSIST prEN 13598-1:2019
prEN 13598-1:2018 (E)
4.2 Abbreviations
DN nominal size
MFR melt mass-flow rate
OIT oxidation induction time
PE polyethylene
PP polypropylene
PP-MD polypropylene modified with minerals
PVC-U unplasticized poly(vinyl chloride)
SDR standard dimension ratio
SN nominal ring stiffness
5 Material
5.1 General
The material, including use of non-virgin material, shall conform to EN 1401-1, EN 1852-1, EN 12666-1,
EN 13476-1, EN 13476-3 or EN 14758-1 as applicable.
Shallow chambers may also be manufactured from non-virgin material in accordance with Annex A.
5.2 Sealing ring retaining components
It is permitted that sealing rings are retained using means made from polymers other than PVC-U, PP or
PE.
6 General characteristics
6.1 Appearance
When viewed without magnification the following requirements apply:
— the internal and external surfaces of ancillary fittings and shallow chambers shall be smooth, clean
and free from grooving, blistering, impurities and pores and any other surface irregularity likely to
prevent their conformity with this standard;
— ancillary fittings and shallow chambers spigots shall be cleanly cut and the ends of pipes and fittings
shall be square to their axis.
6.2 Colour
Ancillary fittings if manufactured in layers shall have their surface layers coloured throughout. The
outside layer of ancillary fittings should preferably be black, orange brown (approxima
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.