SIST EN ISO 18563-2:2017

Non-destructive testing - Characterization and verification of ultrasonic phased array equipment - Part 2: Probes (ISO 18563-2:2017)

This document covers following phased array probes used for ultrasonic non-destructive testing in contact technique (with or without a wedge) or in immersion technique, with centre frequencies in the range 0,5 MHz – 10 MHz.
- linear,
- encircling,
- 2D matrix,
- partial annular sectorial (Type “Daisy”)
This document specifies the characterisation tests that have to be done at the end of the fabrication of a phased array probe. It defines both methodology and acceptance criteria.
This document does not describe methods and acceptance criteria to characterise the performance of an ultrasonic phased array instrument or the performance of a combined system. These are described in EN ISO 18563-1 and in EN ISO 18563-3.

Zerstörungsfreie Prüfung - Charakterisierung und Verifizierung der Ultraschall-Prüfausrüstung mit phasengesteuerten Arrays - Teil 2: Prüfköpfe (ISO 18563-2:2017)

Essais non destructifs - Caractérisation et vérification de l'appareillage de contrôle par ultrasons en multiéléments - Partie 2: Traducteurs (ISO 18563-2:2017)

ISO 18563-2:2017 spécifie les essais de caractérisation effectués à l'issue de la fabrication d'un traducteur multiélément. Il définit à la fois la méthodologie et les critères d'acceptation.
ISO 18563-2:2017 s'applique aux traducteurs multiéléments utilisés pour les essais non destructifs par ultrasons selon la technique par contact (avec ou sans sabot) ou selon la technique par immersion, ayant une fréquence centrale comprise entre 0,5 MHz et 10 MHz:
a)    traducteurs non matriciels:
-      linéaires;
-      encerclants;
-      sectoriels annulaires partiels (type «marguerite»);
b)    traducteurs matriciels 2D.
ISO 18563-2:2017 ne fournit pas les méthodes et critères d'acceptation permettant de caractériser les performances d'un appareil de contrôle par ultrasons en multiéléments ni celles d'un système complet. Ces performances sont données dans l'ISO 18563‑1 et l'ISO 18563‑3.

Neporušitvene preiskave - Karakterizacija in preverjanje ultrazvočne opreme faznih sistemov - 2. del: Sonde (ISO 18563-2:2017)

Ta dokument zajema preskuševalne glave faznih sistemov, ki se uporabljajo za ultrazvočne neporušitvene preiskave s kontaktno tehniko (z lomno prizmo ali brez nje) ali pri tehniki potapljanja, s srednjimi frekvencami v razponu od 0,5 MHz do 10 MHz. – linearno, – s preskusno tuljavo, – 2D-matrično, – delno obročasto sektorsko (tip »Daisy«) Ta dokument določa značilne preskuse, ki jih je treba opraviti ob koncu izdelave sonde faznega sistema. Opredeljuje tako metodologijo kot kriterije sprejemljivosti. Ta dokument ne opisuje metod in kriterijev sprejemljivosti za karakterizacijo delovanja ultrazvočnega instrumenta faznega niza ali delovanja kombiniranega sistema. Ti so opisani v standardih EN ISO 18563-1 in v EN ISO 18563-3.

General Information

• Status: Published
• Public Enquiry End Date: 25-Sep-2016
• Publication Date: 08-Nov-2017
• ICS: 19.100 - Non-destructive testing
• Technical Committee: PKG - Testing of metallic materials
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 08-Sep-2017
• Due Date: 13-Nov-2017
• Completion Date: 09-Nov-2017
• Ref Project: EN ISO 18563-2:2017 - Non-destructive testing - Characterization and verification of ultrasonic phased array equipment - Part 2: Probes (ISO 18563-2:2017)

Relations

• Replaces: SIST EN 16392-2:2014 - Non Destructive Testing - Characterisation and verification of ultrasonic phased array systems - Part 2: Probes
• Effective Date: 06-Sep-2017

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 18563-2:2017
01-december-2017
1DGRPHãþD
SIST EN 16392-2:2014
1HSRUXãLWYHQHSUHLVNDYH.DUDNWHUL]DFLMDLQSUHYHUMDQMHXOWUD]YRþQHRSUHPH
ID]QLKVLVWHPRYGHO6RQGH,62
Non-destructive testing - Characterization and verification of ultrasonic phased array
equipment - Part 2: Probes (ISO 18563-2:2017)
Zerstörungsfreie Prüfung - Charakterisierung und Verifizierung der Ultraschall-
Prüfausrüstung mit phasengesteuerten Arrays - Teil 2: Prüfköpfe (ISO 18563-2:2017)
Essais non destructifs - Caractérisation et vérification de l'appareillage de contrôle par
ultrasons en multiéléments - Partie 2: Traducteurs (ISO 18563-2:2017)
Ta slovenski standard je istoveten z: EN ISO 18563-2:2017
ICS:
19.100 Neporušitveno preskušanje Non-destructive testing
SIST EN ISO 18563-2:2017 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 18563-2:2017

---------------------- Page: 2 ----------------------

SIST EN ISO 18563-2:2017


EN ISO 18563-2
EUROPEAN STANDARD

NORME EUROPÉENNE

August 2017
EUROPÄISCHE NORM
ICS 19.100 Supersedes EN 16392-2:2014
English Version

Non-destructive testing - Characterization and verification
of ultrasonic phased array equipment - Part 2: Probes (ISO
18563-2:2017)
Essais non destructifs - Caractérisation et vérification Zerstörungsfreie Prüfung - Charakterisierung und
de l'appareillage de contrôle par ultrasons en Verifizierung der Ultraschall-Prüfausrüstung mit
multiéléments - Partie 2: Traducteurs (ISO 18563- Phased-Arrays - Teil 2: Prüfköpfe (ISO 18563-2:2017)
2:2017)
This European Standard was approved by CEN on 3 May 2017.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 18563-2:2017 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 18563-2:2017
EN ISO 18563-2:2017 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 18563-2:2017
EN ISO 18563-2:2017 (E)
European foreword
This document (EN ISO 18563-2:2017) has been prepared by Technical Committee ISO/TC 135 “Non-
destructive testing” in collaboration with Technical Committee CEN/TC 138 “Non-destructive testing”
the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by February 2018, and conflicting national standards
shall be withdrawn at the latest by February 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 16392-2:2014.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 18563-2:2017 has been approved by CEN as EN ISO 18563-2:2017 without any
modification.
3

---------------------- Page: 5 ----------------------

SIST EN ISO 18563-2:2017

---------------------- Page: 6 ----------------------

SIST EN ISO 18563-2:2017
INTERNATIONAL ISO
STANDARD 18563-2
First edition
2017-07
Non-destructive testing —
Characterization and verification of
ultrasonic phased array equipment —
Part 2:
Probes
Essais non destructifs — Caractérisation et vérification de
l’appareillage de contrôle par ultrasons en multiéléments —
Partie 2: Traducteurs
Reference number
ISO 18563-2:2017(E)
©
ISO 2017

---------------------- Page: 7 ----------------------

SIST EN ISO 18563-2:2017
ISO 18563-2:2017(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO 2017 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 18563-2:2017
ISO 18563-2:2017(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols . 2
5 General compliance . 2
6 Technical information for phased array probes . 2
7 Test equipment. 4
7.1 Electronic equipment . 4
7.2 Test blocks and other equipment . 4
7.2.1 General. 4
7.2.2 Contact technique . 4
7.2.3 Immersion technique . 4
8 Performance tests for phased array probes . 4
8.1 General . 4
8.2 Physical aspects . 5
8.2.1 Method . 5
8.2.2 Acceptance criterion . 5
8.3 Relative pulse-echo sensitivity variation. 5
8.3.1 General. 5
8.3.2 Method . 5
8.3.3 Acceptance criteria . 5
8.4 Frequency, bandwidth and pulse duration . 6
8.4.1 General. 6
8.4.2 Method . 6
8.4.3 Acceptance criteria . 6
8.5 Probe sensitivity . 7
8.5.1 General. 7
8.5.2 Method . 7
8.5.3 Acceptance criteria . 7
8.6 Inter-element cross-talk (optional) . 7
8.6.1 General. 7
8.6.2 Method . 7
8.6.3 Acceptance criterion . 8
8.7 Number of elements “out of specification” . 8
8.7.1 General. 8
8.7.2 Method . 8
8.7.3 Acceptance criteria . 8
Bibliography . 9
© ISO 2017 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 18563-2:2017
ISO 18563-2:2017(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO’s adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: w w w . i s o .org/ iso/ foreword .html
This document was prepared by the European Committee for Standardization (CEN) Technical
Committee CEN/TC 138, Non-destructive testing, in collaboration with ISO Technical Committee TC 135,
Non-destructive testing, Subcommittee SC 3, Ultrasonic testing, in accordance with the Agreement on
technical cooperation between ISO and CEN (Vienna Agreement).
A list of all parts in the ISO 18563 series
...