Non-destructive testing - Characterization and verification of ultrasonic phased array equipment - Part 2: Probes (ISO 18563-2:2017)

ISO 18563-2:2017 specifies the characterization tests performed at the end of the fabrication of a phased array probe. It defines both methodology and acceptance criteria.
ISO 18563-2:2017 is applicable to the following phased array probes used for ultrasonic non-destructive testing in contact technique (with or without a wedge) or in immersion technique, with centre frequencies in the range 0,5 MHz to 10 MHz:
a)    non-matrix array probes:
-      linear;
-      encircling;
-      partial annular sectorial (type "daisy");
b)    2D-matrix array probes.
ISO 18563-2:2017 does not give methods and acceptance criteria to characterize the performance of an ultrasonic phased array instrument or the performance of a combined system. These are given in ISO 18563?1 and in ISO 18563?3.

Zerstörungsfreie Prüfung - Charakterisierung und Verifizierung der Ultraschall-Prüfausrüstung mit Phased-Arrays - Teil 2: Prüfköpfe (ISO 18563-2:2017)

Essais non destructifs - Caractérisation et vérification de l'appareillage de contrôle par ultrasons en multiéléments - Partie 2: Traducteurs (ISO 18563-2:2017)

ISO 18563-2:2017 spécifie les essais de caractérisation effectués à l'issue de la fabrication d'un traducteur multiélément. Il définit à la fois la méthodologie et les critères d'acceptation.
ISO 18563-2:2017 s'applique aux traducteurs multiéléments utilisés pour les essais non destructifs par ultrasons selon la technique par contact (avec ou sans sabot) ou selon la technique par immersion, ayant une fréquence centrale comprise entre 0,5 MHz et 10 MHz:
a)    traducteurs non matriciels:
-      linéaires;
-      encerclants;
-      sectoriels annulaires partiels (type «marguerite»);
b)    traducteurs matriciels 2D.
ISO 18563-2:2017 ne fournit pas les méthodes et critères d'acceptation permettant de caractériser les performances d'un appareil de contrôle par ultrasons en multiéléments ni celles d'un système complet. Ces performances sont données dans l'ISO 18563‑1 et l'ISO 18563‑3.

Neporušitvene preiskave - Karakterizacija in preverjanje ultrazvočne opreme faznih sistemov - 2. del: Sonde (ISO 18563-2:2017)

Ta dokument zajema preskuševalne glave faznih sistemov, ki se uporabljajo za ultrazvočne neporušitvene preiskave s kontaktno tehniko (z lomno prizmo ali brez nje) ali pri tehniki potapljanja, s srednjimi frekvencami v razponu od 0,5 MHz do 10 MHz. – linearno, – s preskusno tuljavo, – 2D-matrično, – delno obročasto sektorsko (tip »Daisy«) Ta dokument določa značilne preskuse, ki jih je treba opraviti ob koncu izdelave sonde faznega sistema. Opredeljuje tako metodologijo kot kriterije sprejemljivosti. Ta dokument ne opisuje metod in kriterijev sprejemljivosti za karakterizacijo delovanja ultrazvočnega instrumenta faznega niza ali delovanja kombiniranega sistema. Ti so opisani v standardih EN ISO 18563-1 in v EN ISO 18563-3.

General Information

Status
Published
Publication Date
29-Aug-2017
Withdrawal Date
27-Feb-2018
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
30-Aug-2017
Due Date
17-Aug-2018
Completion Date
30-Aug-2017

Relations

Buy Standard

Standard
EN ISO 18563-2:2017
English language
16 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN ISO 18563-2:2016
English language
12 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 18563-2:2017
01-december-2017
1DGRPHãþD
SIST EN 16392-2:2014
1HSRUXãLWYHQHSUHLVNDYH.DUDNWHUL]DFLMDLQSUHYHUMDQMHXOWUD]YRþQHRSUHPH
ID]QLKVLVWHPRYGHO6RQGH ,62
Non-destructive testing - Characterization and verification of ultrasonic phased array
equipment - Part 2: Probes (ISO 18563-2:2017)
Zerstörungsfreie Prüfung - Charakterisierung und Verifizierung der Ultraschall-
Prüfausrüstung mit phasengesteuerten Arrays - Teil 2: Prüfköpfe (ISO 18563-2:2017)
Essais non destructifs - Caractérisation et vérification de l'appareillage de contrôle par
ultrasons en multiéléments - Partie 2: Traducteurs (ISO 18563-2:2017)
Ta slovenski standard je istoveten z: EN ISO 18563-2:2017
ICS:
19.100 Neporušitveno preskušanje Non-destructive testing
SIST EN ISO 18563-2:2017 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 18563-2:2017

---------------------- Page: 2 ----------------------

SIST EN ISO 18563-2:2017


EN ISO 18563-2
EUROPEAN STANDARD

NORME EUROPÉENNE

August 2017
EUROPÄISCHE NORM
ICS 19.100 Supersedes EN 16392-2:2014
English Version

Non-destructive testing - Characterization and verification
of ultrasonic phased array equipment - Part 2: Probes (ISO
18563-2:2017)
Essais non destructifs - Caractérisation et vérification Zerstörungsfreie Prüfung - Charakterisierung und
de l'appareillage de contrôle par ultrasons en Verifizierung der Ultraschall-Prüfausrüstung mit
multiéléments - Partie 2: Traducteurs (ISO 18563- Phased-Arrays - Teil 2: Prüfköpfe (ISO 18563-2:2017)
2:2017)
This European Standard was approved by CEN on 3 May 2017.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 18563-2:2017 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 18563-2:2017
EN ISO 18563-2:2017 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 18563-2:2017
EN ISO 18563-2:2017 (E)
European foreword
This document (EN ISO 18563-2:2017) has been prepared by Technical Committee ISO/TC 135 “Non-
destructive testing” in collaboration with Technical Committee CEN/TC 138 “Non-destructive testing”
the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by February 2018, and conflicting national standards
shall be withdrawn at the latest by February 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 16392-2:2014.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 18563-2:2017 has been approved by CEN as EN ISO 18563-2:2017 without
...

SLOVENSKI STANDARD
oSIST prEN ISO 18563-2:2016
01-september-2016
1HSRUXãLWYHQRSUHVNXãDQMH.DUDNWHUL]DFLMDLQSUHYHUMDQMHXOWUD]YRþQHRSUHPH
ID]QLKVLVWHPRYGHO6RQGH ,62',6
Non-destructive testing - Characterisation and verification of ultrasonic phased array
equipment - Part 2: Probes (ISO/DIS 18563-2:2016)
Zerstörungsfreie Prüfung - Charakterisierung und Verifizierung der Ultraschall-
Prüfausrüstung mit phasengesteuerten Arrays - Teil 2: Prüfköpfe (ISO/DIS 18563-
2:2016)
Ta slovenski standard je istoveten z: prEN ISO 18563-2 rev
ICS:
19.100 Neporušitveno preskušanje Non-destructive testing
oSIST prEN ISO 18563-2:2016 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 18563-2:2016

---------------------- Page: 2 ----------------------
oSIST prEN ISO 18563-2:2016
DRAFT INTERNATIONAL STANDARD
ISO/DIS 18563-2
ISO/TC 135/SC 3 Secretariat: DIN
Voting begins on: Voting terminates on:
2016-07-06 2016-09-27
Non-destructive testing — Characterization and
verification of ultrasonic phased array equipment —
Part 2:
Probes
Essais non destructifs — Caractérisation et vérification de l’appareillage de contrôle par ultrasons en
multiéléments —
Partie 2: Traducteurs
ICS: 19.100
ISO/CEN PARALLEL PROCESSING
This draft has been developed within the European Committee for Standardization
(CEN), and processed under the CEN lead mode of collaboration as defined in the
Vienna Agreement.
This draft is hereby submitted to the ISO member bodies and to the CEN member
THIS DOCUMENT IS A DRAFT CIRCULATED
bodies for a parallel five month enquiry.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
To expedite distribution, this document is circulated as received from the
IN ADDITION TO THEIR EVALUATION AS
committee secretariat. ISO Central Secretariat work of editing and text
BEING ACCEPTABLE FOR INDUSTRIAL,
composition will be undertaken at publication stage.
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 18563-2:2016(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2016

---------------------- Page: 3 ----------------------
oSIST prEN ISO 18563-2:2016
ISO/DIS 18563-2:2016(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved

---------------------- Page: 4 ----------------------
oSIST prEN ISO 18563-2:2016
ISO/DIS 18563-2:2016(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols and abbreviations terms . 2
5 General requirements of conformity . 2
6 Technical information for phased array probes . 2
7 Test equipment.
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.