Controllers with analogue signals for use in industrial-process control systems -- Part 2: Guidance for inspection and routine testing

Provides technical guidance for inspection and routine testing of controllers, for instance, as acceptance tests or after repair.

Regler mit analogen Signalen für die Anwendung in Systemen der industriellen Prozeßtechnik -- Teil 2: Anleitung für die Abnahme- und Betriebsuntersuchung

Régulateurs à signaux analogiques utilisés pour les systèmes de conduite des processus industriels -- Partie 2: Guide pour les essais d'inspection et les essais individuels de série

Fournit un guide technique pour les essais d'inspection et les essais individuels de série des régulateurs utilisés, par exemple, comme essais de réception ou après réparation.

Controllers with analogue signals for use in industrial-process control systems - Part 2: Guidance for inspection and routine testing (IEC 60546-2:1987)

General Information

Status
Published
Publication Date
31-Oct-1998
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
01-Nov-1998
Due Date
01-Nov-1998
Completion Date
01-Nov-1998

Relations

Buy Standard

Standard
SIST EN 60546-2:1998
English language
13 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60546-2:1998
01-november-1998

Controllers with analogue signals for use in industrial-process control systems -

Part 2: Guidance for inspection and routine testing (IEC 60546-2:1987)

Controllers with analogue signals for use in industrial-process control systems -- Part 2:

Guidance for inspection and routine testing
Regler mit analogen Signalen für die Anwendung in Systemen der industriellen
Prozeßtechnik -- Teil 2: Anleitung für die Abnahme- und Betriebsuntersuchung
Régulateurs à signaux analogiques utilisés pour les systèmes de conduite des

processus industriels -- Partie 2: Guide pour les essais d'inspection et les essais

individuels de série
Ta slovenski standard je istoveten z: EN 60546-2:1993
ICS:
25.040.40 Merjenje in krmiljenje Industrial process
industrijskih postopkov measurement and control
SIST EN 60546-2:1998 en

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
NORME CEI
INTERNATIONALE IEC
60546-2
INTERNATIONAL
Première édition
STANDARD
First edition
1987-12
Régulateurs à signaux analogiques utilisés
pour les systèmes de conduite des processus
industriels
Deuxième partie:
Guide pour les essais d'inspection
et les essais individuels de série
Controllers with analogue signals
for use in industrial-process control systems
Part 2:
Guidance for inspection and routine testing
© IEC 1987 Droits de reproduction
réservés — Copyright - all rights reserved
Aucune partie de cette publication ne peut être reproduite ni
No part of this publication may be reproduced or utilized in
utilisée sous quelque forme que ce soit et par aucun
any form or by any means, electronic or mechanical,
procédé, électronique ou mécanique, y compris la photo-
including photocopying and microfilm, without permission in
copie et les microfilms, sans l'accord écrit de l'éditeur.
writing from the publisher.
International Electrotechnical Commission 3, rue de Varembé Geneva, Switzerland
Telefax: +41 22 919 0300 e-mail: inmail ta7
iec.ch IEC web site http: //www.iec.ch
CODE PRIX
Commission Electrotechnique Internationale
PRICE CODE
International Electrotechnical Commission
IEC
MexSayHapwaHaR 3neKrporexHH4eçKaç HoMHCCHfi
Pour prix, voir catalogue en vigueur
• •
For price, see current catalogue
---------------------- Page: 2 ----------------------
546-2 © I E C 1987 — 3 —
INTERNATIONAL ELECTROTECHNICAL COMMISSION
CONTROLLERS WITH ANALOGUE SIGNALS
FOR USE IN INDUSTRIAL-PROCESS CONTROL SYSTEMS
Part 2:
Guidance for inspection and routine testing
FOREWORD

1) The formal decisions or agreements of the IEC on technical matters, prepared by Technical Committees on which all the

National Committees having a special interest therein are represented, express, as nearly as possible, an international

consensus of opinion on the subjects dealt with.

2) They have the form of recommendations for international use and they are accepted by the National Committees in that sense.

3) In order to promote international unification, the IEC expresses the wish that all National Committees should adopt the text

of the IEC recommendation for their national rules in so far as national conditions will permit. Any divergence between the

IEC recommendation and the corresponding national rules should, as far as possible, be clearly indicated in the latter.

PREFACE

This standard has been prepared by Sub-Committee 65B: Elements of Systems, of IEC Technical Com-

mittee No.65: Industrial-process Measurement and Control.
The text of this standard is based on the following documents:
Six Months' Rule Report on Voting
65B(CO)50
65B(CO)57

Full information on the voting for the approval of this standard can be found in the Voting Report indicated

in the above table.
The following IEC publications are quoted in this standard:
Publications Nos. 381: Analogue Signals for Process Control Systems.
382 (1971): Analogue Pneumatic Signal for Process Control Systems.
410 (1973): Sampling Plans and Procedures for Inspection by Attributes.

546-1 (1987): Controllers with Analogue Signals for Use in Industrial-process Control Systems, Part 1:

Methods of Evaluating the Performance.
---------------------- Page: 3 ----------------------
— 5 —
546-2 © I E C 1987
CONTROLLERS WITH ANALOGUE SIGNALS
FOR USE IN INDUSTRIAL-PROCESS CONTROL SYSTEMS
Part 2: Guidance for inspection and routine testing
1. Scope

This standard applies to pneumatic and electrical industrial-process controllers using analogue sig-

nals which are in accordance with I E C Publications 381 and 382. The provisions of this standard are

applicable in principle to controllers having different, but continuous signals.
2. Object

This standard is intended to provide technical guidance for inspection and routine testing of con-

trollers, for instance, as acceptance tests or after repair. For a full evaluation, IEC Publication 546-1

should be used. Quantitative criteria for acceptable performance shall be established by agreement

between manufacturer and user. The requirements of this standard shall be effective when agreed upon

by the manufacturer and the user.
3. Sampling for test

If, by agreement between manufacturer and user, tests are to be performed on a sample lot, it is

recommended that a sampling method such as presented in IEC Publication 410 be selected. When

sampling is used, controllers to be tested may be chosen by the user's inspector.

Symbols and definitions (see IEC Publication 546-1, Sub-clause 3.1 for full list)

4.1 Symbols and definitions used in this standard
t = time
y = output signal (see Figure 1. page 10)
t =
yo = output signal at time 0
measured value (see Figure 1)
x =
w = set point value (see Figure 1)
XP = proportional band
TI = reset time
TD = rate time
KP = proportional action factor
K^ = integral action factor
= derivative action factor
K , expressed in per cent.
Proportional band, X =
Offset = steady-state deviation between measured value, and set point, w.
---------------------- Page: 4 ----------------------
546-2 © IEC 1987
— 7 —
Performance tests

Environmental conditions at the location of testing shall be recorded. See Sub-clause 5.1.1 of I EC

Publication 546-1 for recommended conditions.
The following tests shall be performed:
5.1 Tests of controller action (only
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.