SIST ISO 1829:1999
(Main)Selection of tolerance zones for general purposes
Selection of tolerance zones for general purposes
Gives the possibility of a very extended selection of different symbols for tolerance zones. Includes upper and lower deviations for holes (internal features) and shafts (external features). Gives recommendations for selection.
Sélection de zones de tolérances pour usages généraux
Izbira tolerančnih polj za splošno rabo
General Information
RELATIONS
Standards Content (sample)
INTEliNATlONAL STANDARD.
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION l MEXAYHAPOAHPJI OPI-AHM3AUWfi I-IO =AHAAPTtI3AUMM*ORGANISATlON INTERNATIONALE DE NORMALISATION
Selection of tolerance zones for general purposesSe ’iection de zones de tolkances pour usages gh?raux
First edition - 1975.006-15
Ref. No. IS0 18294975 (E)
UDC 621.753.1/.2 : 389.17
Descriptors : dimensional tolerances, fits, selection.
Price based on 2 pages
---------------------- Page: 1 ----------------------
FOREWORD
IS0 (the International Organization for Standardization) is a worldwide federation
of national standards institutes (IS0 Member Bodies). The work of developinginternational Standards is carried out through IS0 Technical Committees. Every
Member Body interested in a subject for which a Technical Committee has been set
up has the right to be represented on that Committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work.
Draft International Standards adopted by the Techrltcal Committees are circulated
to the Member Bodies for approval before their acceptance as InternationalStandards by the IS0 Council.
Prior to 1972, the results of the work of the Technical Committees were published
as IS0 Recommendations; these documents are now in the process of beingtransformed into International Standards. As part uf this process, Technical
Committee ISO/TC 3 has reviewed IS0 Recommendation R 1829 and found it
technically suitable for transformation. International Standard IS0 1829 therefore
replaces IS0 Recommendation R 1829-1970 to which it is technically identical.IS0 Recommenda tion R 1829 was approved bv the Member Bodies of the
folio wing countries
Romania
Austria India
Brazil Israel Spain
South Africa, Rep. oi
Chile Japan
Sweden
Czechoslovakia Netherlands
New Zealand Switzerland
Egypt, Arab Rep. of
Turkey
Germany Norway
Peru United Kingdom
Greece
Poland U.S.S.R.
Hungary
The Member Bodies of the following countries expressed disapproval of the
Recommendation on technical grounds :
Belgium
Canada
France
. Portugal
The Member Body of the following country disapproved the transformation of
ISO/R 1829 into an International Standard :
Australia
0 International Organization for Standardization, 1975 l
Printed in Switzerland
---------------------- Page: 2 ----------------------
IS0 18294975 (E)
INTERNATIONAL STANDARD ’
Selection of tolerance zones for general purposes
0 INTRODUCTION
ISO/R 286, /SO System of limits and fits - Part I : General, tolerances and deviations, gives the possibility of a very wide
choice among the various symbols for tolerance zones that it contains, even if this choice is limited only to those shown in i
...SLOVENSKI STANDARD
SIST ISO 1829:1999
01-marec-1999
,]ELUDWROHUDQþQLKSROM]DVSORãQRUDER
Selection of tolerance zones for general purposes
Sélection de zones de tolérances pour usages généraux
Ta slovenski standard je istoveten z: ISO 1829:1975
ICS:
17.040.10 Tolerance in ujemi Limits and fits
SIST ISO 1829:1999 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------SIST ISO 1829:1999
---------------------- Page: 2 ----------------------
SIST ISO 1829:1999
INTEliNATlONAL STANDARD.
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION l MEXAYHAPOAHPJI OPI-AHM3AUWfi I-IO =AHAAPTtI3AUMM*ORGANISATlON INTERNATIONALE DE NORMALISATION
Selection of tolerance zones for general purposesSe ’iection de zones de tolkances pour usages gh?raux
First edition - 1975.006-15
Ref. No. IS0 18294975 (E)
UDC 621.753.1/.2 : 389.17
Descriptors : dimensional tolerances, fits, selection.
Price based on 2 pages
---------------------- Page: 3 ----------------------
SIST ISO 1829:1999
FOREWORD
IS0 (the International Organization for Standardization) is a worldwide federation
of national standards institutes (IS0 Member Bodies). The work of developinginternational Standards is carried out through IS0 Technical Committees. Every
Member Body interested in a subject for which a Technical Committee has been set
up has the right to be represented on that Committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work.
Draft International Standards adopted by the Techrltcal Committees are circulated
to the Member Bodies for approval before their acceptance as InternationalStandards by the IS0 Council.
Prior to 1972, the results of the work of the Technical Committees were published
as IS0 Recommendations; these documents are now in the process of beingtransformed into International Standards. As part uf this process, Technical
Committee ISO/TC 3 has reviewed IS0 Recommendation R 1829 and found it
technically suitable for transformation. International Standard IS0 1829 therefore
replaces IS0 Recommendation R 1829-1970 to which it is technically identical.IS0 Recommenda tion R 1829 was approved bv the Member Bodies of the
folio wing countries
Romania
Austria India
Brazil Israel Spain
South Africa, Rep. oi
Chile Japan
Sweden
Czechoslovakia Netherlands
New Zealand Switzerland
Egypt, Arab Rep. of
Turkey
Germany Norway
Peru United Kingdom
Greece
Poland U.S.S.R.
Hungary
The Member Bodies of the following countries expressed disapproval of the
Recommendation on technical grounds :
Belgium
Canada
France
. Portugal
The Member Body of the following country disapproved the transformation of
ISO/R 1829 into an International Standard :
Australia
0 International Organization for Standardization, 1975 l
Printed in Switzerland
---------------------- Page: 4 ----------------------
SIST ISO 1829:1999
IS0 18294975 (E)
INTERNATIONAL STANDARD ’
Selection of tol
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.