iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 1335-3:2001

(Main)

Office furniture - Office work chair - Part 3: Safety test methods

Office furniture - Office work chair - Part 3: Safety test methods

This part of prEN 1335:1999 specifies the test methods to be applied when testing the safety of office work chairs. The corresponding safety requirements are found in prEN 1335-2:1999. This European Standard does not specify type approval tests for chair components. The tests in clause 8, 9 and 10 are based upon use by persons weighing up to 110 kg for eight hours a day. For more severe conditions of use, increased requirements will be necessary.

Büromöbel - Büro-Arbeitsstuhl - Teil 3: Sicherheitsprüfungen

Dieser Teil der prEN 1335:1999 legt Prüfmethoden fest, die zur Prüfung der Sicherheit von Büro-Arbeitsstühlen angewendet werden müssen. Die zugehörigen Anforderungen sind in prEN 1335-2:1999 festgelegt. Diese Norm legt keine Bauartprüfungen für Bauteile von Büro-Arbeitsstühlen fest. Die Prüfanforderungen in den Abschnitten 7, 8 und 9 berücksichtigen eine Benutzung von täglich acht Stunden durch Personen mit einem Gewicht bis zu 110 kg. Bei höheren Beanspruchungen ist es notwendig, die Anforderungen zu erhöhen.

Mobilier de bureau - Siege de travail de bureau - Partie 3: Essais de sécurité

La présente partie du prEN 1335:1999 fixe les méthodes d'essai a appliquer lors de la vérification de la sécurité des sieges de bureau pivotants. Les exigences de sécurité correspondantes sont données dans le prEN 1335-2:1999. Cette norme ne prévoit pas d'essais spécifiques pour les composants constitutifs des sieges. Les exigences d'essai des paragraphes 8, 9 et 10 sont basées sur une utilisation par des personnes pesant jusqu'a 110 kg pendant 8 heures par jour. Pour des conditions d'utilisation plus séveres, des exigences plus élevées sont a prévoir.

Pisarniško pohištvo - Pisarniški delovni stoli - 3. del: Varnostne preskusne metode

General Information

Status
Withdrawn
Publication Date
31-Jan-2001
Withdrawal Date
16-Dec-2009
ICS
97.140 - Furniture
Technical Committee
POH - Furniture
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
03-Dec-2009
Due Date
26-Dec-2009
Completion Date
17-Dec-2009
Ref Project
EN 1335-3:2000 - Office furniture - Office work chair - Part 3: Safety test methods

Relations

Replaced By
SIST EN 1335-3:2010 - Office furniture - Office work chair - Part 3: Test methods
Effective Date
01-Jan-2010

Buy Standard

EN 1335-3:2001EN 1335-3:2001
PreviousNext
Standard
EN 1335-3:2001
English language
19 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Pisarniško pohištvo - Pisarniški delovni stoli - 3. del: Varnostne preskusne metodeBüromöbel - Büro-Arbeitsstuhl - Teil 3: SicherheitsprüfungenMobilier de bureau - Siege de travail de bureau - Partie 3: Essais de sécuritéOffice furniture - Office work chair - Part 3: Safety test methods97.140PohištvoFurnitureICS:Ta slovenski standard je istoveten z:EN 1335-3:2000SIST EN 1335-3:2001en01-februa
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 1729-2:2023(Main)
Furniture - Chairs and tables for educational institutions - Part 2: Safety requirements and test methods
EN 1729-2:2023

This document specifies safety requirements and test methods for chairs and tables for general educational purposes in educational institutions including kindergarten, childcare institutions and early years education settings.
It applies to furniture for use with laptop computers or portable devices, but not to special purpose workstations, e.g. laboratories, ranked seating and workshops.
The chairs fulfilling the applicable requirements of this document are suitable for users weighing up to 110 kg.
The figures illustrate test principles only and cannot be used to carry out the tests.
NOTE   EN 1729-1 specifies functional dimensions and marking of chairs and tables for general educational purposes.
Annex A (informative) Test method for determination of the displacement of chairs placed on tabletops.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 13721:2023(Main)
Furniture - Assessment of the surface reflectance
EN 13721:2023

This document specifies a method for the assessment of the surface reflectance of furniture surfaces and relates to rigid surfaces of all finished products regardless of materials, except for finishes on leather and fabrics, which are excluded from this document.
The test is intended to be carried out on finished furniture, but can be carried out on test panels of the same material, finished in an identical manner to the finished product, and of a size sufficient to meet the requirements of the test.
The test method is not applicable to some metallic paints and pearly coatings.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 16611:2023(Main)
Furniture - Assessment of the surface resistance to microscratching
EN 16611:2023

This document specifies a method for the assessment of the surface resistance to microscratching and relates to rigid surfaces of all finished products, considering the following exceptions:.
Method A is suitable for all types of surface coatings and coverings except for lacquers with pearly or metallic effects.
Method B is suitable for all types of surface.
No method applies to finishes on leather and fabrics.
The test is intended to be carried out on a part of finished furniture, but can be carried out on test panels of the same material, finished in an identical manner to the finished product, and of a size sufficient to meet the requirements of the test.
It is essential that the test is carried out on unused surfaces.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 17869:2023(Main)
Hardware for furniture - Test method for strength and overload tests of connectors for furniture constructed from panel material
EN 17869:2023

This document specifies test methods for the strength and overload tests of connectors for furniture constructed from panel material and procedures for evaluating test results.
The document is specifically intended for assessing of cabinet connectors for carcases made of wood-based panel materials. The methods described can, however, be used to assess the relative performance of other types of connectors, e.g. some types of connectors for beds.
The strength and overload tests only apply to the connectors and their components, as well as the mounting to and in the cabinet carcase.  It does not apply to additional functions that the connector may have e.g. covering of the connector.
The tests described are carried according to a test setup with specified properties and characteristics.
The test results are only valid for the connector tested. The results can be used to represent the performance of production models, provided the tested model is representative of the production model.
Aging and the influences of temperature and humidity are not included. The standard contains four informative annexes, providing additional methodologies for the detailed evaluation of the test results, and a procedure for comparing the tested connector with a reference connector.
Annex A (informative) – Reference connector – Glued dowel
Annex B (informative) – Ratio generation
Annex C (informative) – Stiffness calculation for further evaluation of the overload
Annex D (informative) – Evaluation by the characteristic value (5% percentile)

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 17737:2023(Main)
Hardware for furniture - Test and evaluation methods for the corrosion resistance of furniture fittings
EN 17737:2022

This European standard specifies test methods for the determination of corrosion resistance of furniture fittings as ready-to-use assemblies or their individual parts.
It applies to the optical assessment of surface changes for the following materials:
•   Metals and their alloys
•   Metal coatings with anodic or cathodic properties
•   Conversion coatings
•   Anodic oxide layers
•   Organic coatings on metallic materials
This document does not include any requirements. These should be in the product specifications.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1335-1:2020+A1:2023(Main)
Office furniture - Office work chair - Part 1: Dimensions - Determination of dimensions
EN 1335-1:2020+A1:2022

This part of prEN 1335:2017 applies to office work chairs. It specifies dimensions of three types of chairs as well as test methods for their determination.
Annex A (informative) contains a Rationale for office chair features and comparison between current published dimensions with European anthropometric data.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 14749:2016+A1:2022(Main)
Furniture - Domestic and kitchen storage units and kitchen-worktops - Safety requirements and test methods
EN 14749:2016+A1:2022

This European Standard specifies safety requirements and test methods for all types of kitchen and bathroom storage units and domestic storage furniture and their components.
It does not apply to non-domestic storage, office storage, industrial storage, catering equipment, retail storage and industrial storage lockers.
It does not apply to units covered by EN 71 1, Safety of toys - Part 1: Mechanical and physical properties and EN 60065, Audio, video and similar electronic apparatus - Safety requirements (IEC 60065).
It does not include requirements for the resistance to ageing, degradation, flammability and electrical safety.
Safety that is dependent upon the structure of the building is not included, e.g. the strength of wall hanging units includes only the cabinet and its components including wall attachment devices. The wall and the wall attachments are not included.
Annex A (normative) contains additional test methods.
Annex B (informative) contains a guide to testing of units and components according to this document.
Annex C (informative) contains an example of loading of wall hanging units.
Annex D (informative) contains a method for calculation of vertical and horizontal acting forces.

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TS CEN/TS 16209:2022(Main)
Furniture - Classification for properties for furniture surfaces
CEN/TS 16209:2022

This Technical Specification specifies a system for the classification of the resistance to:
   Dry heat
   Wet heat
   Cold liquids
   Abrasion
   Scratching
   Microscratching
The classification applies to foils, laminates, melamine faced boards, pigmented and transparent lacquers. The classification for the resistance to cold liquids also applies to oils and waxes.
The following classification does not apply to leather surfaces.

  • Technical specification
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 17191:2021(Main)
Children’s Furniture - Seating for children - Safety requirements and test methods
EN 17191:2021

This European Standard specifies safety requirements and test methods for seating for children who are able to walk and sit by themselves.
It applies to seating intended to be placed on the floor for all fields of application with the exception of the use in educational institutions.
This European Standard applies to the seating function only. If the furniture has additional functions or can be converted into other products, the relevant European Standards may apply.
It does not apply to children’s high chairs and reclined cradles for which other European Standards exist.
It does not apply to wheel chairs, electrical powered chairs and seating for children with special needs.

  • Standard
    49 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    44 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 16890:2017+A1:2021(Main)
Children's furniture - Mattresses for cots and cribs - Safety requirements and test methods
EN 16890:2017+A1:2021

This European Standard specifies safety requirements and test methods for mattresses including mattress bases and mattress toppers, used in children's cots, travel cots, cribs and suspended baby beds, for domestic and non-domestic use.
This European Standard does not apply to mattresses for carry cots and pram bodies, inflatable mattresses, water mattresses and mattresses used for medical purposes.

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day