SIST EN 13523-0:2014
(Main)Coil coated metals - Test methods - Part 0: General introduction and list of test methods
Coil coated metals - Test methods - Part 0: General introduction and list of test methods
EN 13523-0 specifies test methods for organic coatings on coil coated metals. This part of EN 13523 specifies the overall scope of all parts of EN 13523, gives definitions common to all parts and describes how sampling and preparation of test panels for most of the individual test methods are to be carried out.
Bandbeschichtete Metalle - Prüfverfahren - Teil 0: Allgemeine Einleitung und Liste der Prüfverfahren
EN 13523 legt Prüfverfahren für organische Beschichtungen auf bandbeschichteten Metallen fest.
Dieser Teil von EN 13523 legt den Anwendungsbereich aller Teile von EN 13523 fest und enthält Definitionen, die für alle Teile gelten. Er beschreibt auch, wie Proben zu nehmen sind und Probenplatten für die meisten der angegebenen Prüfverfahren hergestellt werden.
Tôles prélaquées - Méthodes d'essai - Partie 0 : Introduction générale et liste des méthodes d'essai
L’EN 13523 traite des méthodes d’essai des revêtements organiques sur les tôles prélaquées.
La présente partie de l’EN 13523 spécifie le domaine d’application de l’ensemble des parties de l’EN 13523, donne les définitions communes à toutes les parties et décrit comment effectuer l’échantillonnage et la préparation des éprouvettes pour la plupart des méthodes d’essai.
Prevlečene kovine, ki se navijajo - Preskusne metode - 0. del: Splošni uvod in seznam preskusnih metod
Standard EN 13523-0 določa preskusne metode za organske prevleke na prevlečenih kovinah, ki se navijajo. Ta del standarda EN 13523 določa skupni obseg vseh delov standarda EN 13523, podaja definicije, ki so skupne vsem delom, in opisuje, kako je treba izvesti vzorčenje in pripravo testnih panelov za večino posameznih preskusnih metod, ki jih je treba izvesti.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Bandbeschichtete Metalle - Prüfverfahren - Teil 0: Allgemeine Einleitung und Liste der PrüfverfahrenTôles prélaquées - Méthodes d'essai - Partie 0 : Introduction générale et liste des méthodes d'essaiCoil coated metals - Test methods - Part 0: General introduction and list of test methods25.220.60Organske prevlekeOrganic coatings17.040.20Lastnosti površinProperties of surfacesICS:Ta slovenski standard je istoveten z:EN 13523-0:2014SIST EN 13523-0:2014en,fr,de01-september-2014SIST EN 13523-0:2014SLOVENSKI
STANDARDSIST EN 13523-0:20021DGRPHãþD
SIST EN 13523-0:2014
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13523-0
June 2014 ICS 25.220.60 Supersedes EN 13523-0:2001English Version
Coil coated metals - Test methods - Part 0: General introduction Tôles prélaquées - Méthodes d'essai - Partie 0 : Introduction générale
Bandbeschichtete Metalle - Prüfverfahren - Teil 0: Allgemeine Einleitung This European Standard was approved by CEN on 7 May 2014.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13523-0:2014 ESIST EN 13523-0:2014
EN 13523-0:2014 (E) 2 Contents Page Foreword .3 1 Scope .5 2 Normative references .5 3 Terms and definitions .5 4 Sampling .6 5 Preparation of test panels .6 6 Conditioning of test panels .6 7 Test conditions .7 Bibliography .8
SIST EN 13523-0:2014
EN 13523-0:2014 (E) 3 Foreword This document (EN 13523-0:2014) has been prepared by Technical Committee CEN/TC 139 “Paints and varnishes”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2014, and conflicting national standards shall be withdrawn at the latest by December 2014. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 13523-0:2001. The main technical changes are: a) the title of the standard was changed; b) the definitions were aligned with those in EN ISO 4618; c) the list of the existing parts of EN 13523 was updated; d) a note on rolling direction was added; e) the normative references were updated. EN 13523, Coil coated metals — Test methods, consists of the following parts: — Part 0: General introduction — Part 1: Film thickness — Part 2: Gloss — Part 3: Colour difference — Instrumental comparison — Part 4: Pencil hardness — Part 5: Resistance to rapid deformation (impact test) — Part 6: Adhesion after indentation (cupping test) — Part 7: Resistance to cracking on bending (T-bend test) — Part 8: Resistance to salt spray (fog) — Part 9: Resistance to water immersion — Part 10: Resistance to fluorescent UV radiation and water condensation — Part 11: Resistance to solvents (rubbing test) — Part 12: Resistance to scratching — Part 13: Resistance to accelerated ageing by the use of heat SIST EN 13523-0:2014
EN 13523-0:2014 (E) 4 — Part 14: Chalking (Helmen method) — Part 15: Metamerism — Part 16: Resistance to abrasion — Part 17: Adhesion of strippable films — Part 18: Resistance to staining — Part 19: Pan
...
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Bandbeschichtete Metalle - Prüfverfahren - Teil 0: Allgemeine Einleitung und Liste der PrüfverfahrenTôles prélaquées - Méthodes d'essai - Partie 0 : Introduction générale et liste des méthodes d'essaiCoil coated metals - Test methods - Part 0: General introduction and list of test methods25.220.60Organske prevlekeOrganic coatings17.040.20Lastnosti površinProperties of surfacesICS:Ta slovenski standard je istoveten z:FprEN 13523-0kSIST FprEN 13523-0:2014en,fr,de01-marec-2014kSIST FprEN 13523-0:2014SLOVENSKI
STANDARD
kSIST FprEN 13523-0:2014
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
FINAL DRAFT
FprEN 13523-0
February 2014 ICS 25.220.60 Will supersede EN 13523-0:2001English Version
Coil coated metals - Test methods - Part 0: General introduction Tôles prélaquées - Méthodes d'essai - Partie 0 : Introduction générale
Bandbeschichtete Metalle - Prüfverfahren - Teil 0: Allgemeine Einleitung This draft European Standard is submitted to CEN members for formal vote. It has been drawn up by the Technical Committee CEN/TC 139.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. FprEN 13523-0:2014 EkSIST FprEN 13523-0:2014
FprEN 13523-0:2013 (E) 2 Contents Page Foreword .3 1 Scope .4 2 Normative references .4 3 Terms and definitions .5 4 Sampling .6 5 Preparation of test panels .6 6 Conditioning of test panels .6 7 Test conditions .6 Bibliography .7
kSIST FprEN 13523-0:2014
FprEN 13523-0:2013 (E) 3 Foreword This document (FprEN 13523-0:2014) has been prepared by Technical Committee CEN/TC 139 “Paints and varnishes”, the secretariat of which is held by DIN. This document is currently submitted to the Formal Vote. This document will supersede EN 13523-0:2001. The main technical changes are: a) the title of the standard was changed; b) the definitions were aligned with those in EN ISO 4618; c) the list of the existing parts of EN 13523 was updated; d) a note on rolling direction was added; e) the normative references were updated. EN 13523, Coil coated metals — Test methods, consists of the following parts: — Part 0: General introduction — Part 1: Film thickness — Part 2: Gloss — Part 3: Colour difference — Instrumental comparison — Part 4: Pencil hardness — Part 5: Resistance to rapid deformation (impact test) — Part 6: Adhesion after indentation (cupping test) — Part 7: Resistance to cracking on bending (T-bend test) — Part 8: Resistance to salt spray (fog) — Part 9: Resistance to water immersion — Part 10: Resistance to fluorescent UV radiation and water condensation — Part 11: Resistance to solvents (rubbing test) — Part 12: Resistance to scratching — P
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.