EN 13523-0:2021
(Main)Coil coated metals - Test methods - Part 0: General introduction
Coil coated metals - Test methods - Part 0: General introduction
This document specifies the overall scope of all parts of EN 13523, gives definitions common to all parts and describes how sampling and preparation of test panels for most of the individual test methods are to be carried out.
Bandbeschichtete Metalle - Prüfverfahren - Teil 0: Allgemeine Einleitung
Dieses Dokument legt den Anwendungsbereich aller Teile von EN 13523 fest und enthält Definitionen, die für alle Teile gelten. Es beschreibt, wie Proben zu nehmen sind und Probenplatten für die meisten der angegebenen Prüfverfahren hergestellt werden.
Tôles prélaquées - Méthodes d'essai - Partie 0 : Introduction générale
Le présent document spécifie le domaine d’application de l’ensemble des parties de l’EN 13523, donne les définitions communes à toutes les parties et décrit comment effectuer l’échantillonnage et la préparation des panneaux d’essai pour la plupart des méthodes d’essai.
Prevlečene kovine, ki se navijajo - Preskusne metode - 0. del: Splošni uvod
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2021
Nadomešča:
SIST EN 13523-0:2014
Prevlečene kovine, ki se navijajo - Preskusne metode - 0. del: Splošni uvod
Coil coated metals - Test methods - Part 0: General introduction
Bandbeschichtete Metalle - Prüfverfahren - Teil 0: Allgemeine Einleitung
Tôles prélaquées - Méthodes d'essai - Partie 0 : Introduction générale
Ta slovenski standard je istoveten z: EN 13523-0:2021
ICS:
17.040.20 Lastnosti površin Properties of surfaces
25.220.60 Organske prevleke Organic coatings
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN 13523-0
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2021
EUROPÄISCHE NORM
ICS 25.220.60 Supersedes EN 13523-0:2014
English Version
Coil coated metals - Test methods - Part 0: General
introduction
Tôles prélaquées - Méthodes d'essai - Partie 0 : Bandbeschichtete Metalle - Prüfverfahren - Teil 0:
Introduction générale Allgemeine Einleitung
This European Standard was approved by CEN on 16 August 2021.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13523-0:2021 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Sampling . 6
5 Preparation of test panels . 6
6 Conditioning of test panels . 7
7 Test conditions . 7
Bibliography . 8
European foreword
This document (EN 13523-0:2021) has been prepared by Technical Committee CEN/TC 139 “Paints and
varnishes”, the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2022, and conflicting national standards shall be
withdrawn at the latest by April 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 13523-0:2014.
The main changes are:
a) the definitions have been aligned with those in EN ISO 4618;
b) the bibliography has been updated;
c) the list of the existing parts of EN 13523 has been updated;
d) the text has been editorially revised and the normative references have been updated.
The EN 13523 series, Coil coated metals — Test methods, consists of the following parts:
— Part 0: General introduction
— Part 1: Film thickness
— Part 2: Gloss
— Part 3: Colour difference and metamerism — Instrumental comparison
— Part 4: Pencil hardness
— Part 5: Resistance to rapid deformation (impact test)
— Part 6: Adhesion after indentation (cupping test)
— Part 7: Resistance to cracking on bending (T-bend test)
— Part 8: Resistance to salt spray (fog)
— Part 9: Resistance to water immersion
— Part 10: Resistance to fluorescent UV radiation and water condensation
— Part 11: Resistance to solvents (rubbing test)
— Part 12: Resistance to scratching
— Part 13: Resistance to accelerated ageing by the use of heat
— Part 14: Chalking (Helmen method)
— Part 16: Resistance to abrasion
— Part 17: Adhesion of strippable films
— Part 18: Resistance to staining
— Part 19
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.