SIST EN IEC 63461:2024
(Main)Pelton hydraulic turbines - Model acceptance tests (IEC 63461:2024)
Pelton hydraulic turbines - Model acceptance tests (IEC 63461:2024)
IEC 63461:2024 applies to laboratory model tests of any type of Pelton hydraulic turbine with unit power greater than 5 MW. It contains the rules governing test conduct and provides measures to be taken if any phase of the tests is disputed.
The main objectives of this document are:
- to define the terms and quantities used;
- to specify methods of testing and of measuring the quantities involved, in order to ascertain the hydraulic performance of the model;
- to specify the methods of computation of results and of comparison with guarantees;
- to determine if the contract guarantees that fall within the scope of this document have been fulfilled;
- and to define the extent, content and structure of the final report.
Full application of the procedures herein described is not generally justified for machines with smaller power. Nevertheless, this document can be used for such machines by agreement between the purchaser and the supplier.
Hydraulische Pelton Turbinen - Modellabnahmeprüfungen (IEC 63461:2024)
Turbines hydrauliques Pelton - Essais de réception sur modèle (IEC 63461:2024)
IEC 63461:2024 s’applique aux essais de modèles de laboratoire de tout type de turbine Pelton d’une puissance unitaire supérieure à 5 MW. Il fixe les règles de conduite de ces essais et spécifie les mesures à prendre en cas de contestation d’une phase quelconque des essais.
Les principaux objectifs du présent document sont les suivants:
- définir les termes et les grandeurs utilisés;
- spécifier les méthodes d'essai et de mesure des grandeurs concernées, afin de déterminer les performances hydrauliques du modèle;
- spécifier les méthodes de calcul des résultats et de comparaison avec les garanties;
- déterminer si les garanties contractuelles qui relèvent du domaine d’application du présent document sont respectées;
- et définir l’étendue, le contenu et la structure du rapport final.
L’application intégrale des procédures décrites dans le présent document ne se justifie généralement pas pour les machines de puissance inférieure. Néanmoins, le présent document peut être utilisé pour de telles machines après accord entre l’acheteur et le fournisseur.
Peltonove vodne turbine - Prevzemni preskusi modela (IEC 63461:2024)
Standard IEC 63461:2024 se uporablja za laboratorijske preskuse modela Peltonove vodne turbine katere koli vrste z močjo enote, večjo od 5 MW. Vsebuje pravila, ki urejajo izvajanje preskusov, in določa ukrepe, ki jih je treba izvesti v primeru sporov glede ene od faz preskusov.
Glavni namen tega dokumenta je:
– opredelitev izrazov in količin, ki se uporabljajo;
– določitev metod za preskušanje in merjenje vključenih količin, da se opredeli hidravlična zmogljivost modela;
– določitev metod za izračun rezultatov in primerjavo z jamstvi;
– ugotovitev, ali so pogodbena jamstva, ki spadajo na področje uporabe tega dokumenta, izpolnjena; ter
– določitev obsega, vsebine in strukture končnega poročila.
Celotna uporaba postopkov, opisanih v tem dokumentu, na splošno ni utemeljena za stroje z manjšo močjo. Kljub temu pa je mogoče po dogovoru med kupcem in dobaviteljem ta dokument uporabiti tudi za take stroje .
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-oktober-2024
Peltonove vodne turbine - Prevzemni preskusi modela (IEC 63461:2024)
Pelton hydraulic turbines - Model acceptance tests (IEC 63461:2024)
Hydraulische Pelton Turbinen - Modellabnahmeprüfungen (IEC 63461:2024)
Turbines hydrauliques Pelton - Essais de réception sur modèle (IEC 63461:2024)
Ta slovenski standard je istoveten z: EN IEC 63461:2024
ICS:
27.140 Vodna energija Hydraulic energy engineering
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN IEC 63461
NORME EUROPÉENNE
EUROPÄISCHE NORM August 2024
ICS 27.140 Supersedes EN IEC 60193:2019
English Version
Pelton hydraulic turbines - Model acceptance tests
(IEC 63461:2024)
Turbines Pelton - Essais de réception sur modèle Hydraulische Pelton Turbinen - Modellabnahmeprüfungen
(IEC 63461:2024) (IEC 63461:2024)
This European Standard was approved by CENELEC on 2024-08-02. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 63461:2024 E
European foreword
The text of document 4/460/CDV, future edition 1 of IEC 63461, prepared by IEC/TC 4 "Hydraulic
turbines" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2025-05-02
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2027-08-02
document have to be withdrawn
This document supersedes EN IEC 60193:2019 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 63461:2024 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standard indicated:
IEC 60041:1991 NOTE Approved as EN 60041:1994
IEC 60609-1:2004 NOTE Approved as EN 60609-1:2005 (not modified)
IEC 60609-2:1997 NOTE Approved as EN 60609-2:1999 (not modified)
IEC 60994:1991 NOTE Approved as EN 60994:1992 (not modified)
ISO 4006:1991 NOTE Approved as EN 24006:1993 (not modified)
ISO 4373:2022 NOTE Approved as EN ISO 4373:2022 (not modified)
ISO 5167-1:2022 NOTE Approved as EN ISO 5167-1:2022 (not modified)
ISO 20456:2017 NOTE Approved as EN ISO 20456:2019 (not modified)
ISO 80000-4:2019 NOTE Approved as EN ISO 80000-4:2019 (not modified)
ISO 80000-11:2019 NOTE Approved as EN ISO 80000-11:2020 (not modified)
ISO 21920-2:2021 NOTE Approved as EN ISO 21920-2:2022 (not modified)
IEC 60609 series NOTE Approved as EN 60609 series
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cencenelec.eu.
Publication Year Title EN/HD Year
ISO 2186 2007 Fluid flow in closed conduits_- Connections - -
for pressure signal transmissions between
primary and secondary elements
ISO 2533 1975 Standard Atmosphere - -
ISO 4185 1980 Measurement of liquid flow in closed EN 24185 1993
conduits - Weighing method
- - + AC 1993
ISO 8316 1987 Measurement of liquid flow in closed EN ISO 8316 1995
conduits - Method by collection of the liquid
in a volumetric tank
IEC 63461 ®
Edition 1.0 2024-06
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Pelton hydraulic turbines – Model acceptance tests
Turbines Pelton – Essais de réception sur modèle
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 27.140 ISBN 978-2-8322-9236-5
– 2 – IEC 63461:2024 © IEC 2024
CONTENTS
FOREWORD . 9
1 Scope . 11
2 Normative references . 12
3 Terms, definitions, symbols and units . 12
3.1 General . 12
3.2 Terms and definitions. 12
3.3 Units . 14
3.4 Terms, definitions, symbols and units . 14
3.4.1 List by topics . 14
3.4.2 Subscripts and symbols . 15
3.4.3 Geometry . 16
3.4.4 Physical quantities and properties . 17
3.4.5 Discharge, velocity and speed . 18
3.4.6 Pressure . 18
3.4.7 Specific energy . 19
3.4.8 Height and head . 19
3.4.9 Power and torque . 20
3.4.10 Efficiency . 22
3.4.11 Fluctuating quantities . 22
3.4.12 Fluid dynamics and scaling . 25
3.4.13 Dimensionless terms and definitions . 25
3.4.14 Additional performance data . 26
4 Physical properties . 26
4.1 General . 26
4.2 Acceleration due to gravity . 26
4.3 Physical properties of water . 27
4.3.1 Density of water . 27
4.3.2 Kinematic viscosity . 30
4.3.3 Vapour pressure . 30
4.4 Physical conditions of atmosphere . 31
4.4.1 Density of dry air . 31
4.4.2 Ambient pressure . 31
4.5 Density of mercury . 31
5 Requirements of tests . 32
5.1 Requirement of test installation and model . 32
5.1.1 Choice of laboratory . 32
5.1.2 Test installation . 32
5.1.3 Model requirements . 33
5.2 Dimensional check of model and prototype . 35
5.2.1 General . 35
5.2.2 Explanation of terms used for model and prototype. 36
5.2.3 Purpose of dimensional checks. 36
5.2.4 General rules . 36
5.2.5 Procedure . 37
5.2.6 Methods . 38
5.2.7 Accuracy of measurements . 41
5.2.8 Dimensions of model and prototype to be checked . 41
IEC 63461:2024 © IEC 2024 – 3 –
5.2.9 Permissible maximum deviations in geometrical similarity between
prototype and model . 43
5.2.10 Surface waviness and roughness . 44
5.3 Test procedures . 46
5.3.1 Organization of tests. 46
5.3.2 Inspections and calibrations . 48
5.3.3 Execution of tests . 50
5.3.4 Faults and repetition of tests . 54
5.3.5 Preliminary test report . 55
5.3.6 Final test report . 55
6 Data acquisition . 55
6.1 Data acquisition and data processing . 55
6.1.1 General . 55
6.1.2 General requirements . 56
6.1.3 Data acquisition . 56
6.1.4 Component requirements . 58
6.1.5 Check of the data acquisition system . 61
6.2 Data acquisition and processing for measurement of fluctuating quantities . 63
6.2.1 General .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.