SIST EN 13880-12:2004

Hot applied joint sealants - Part 12: Test method for the manufacture of concrete test blocks for bond testing (recipe methods)

This European Standard describes a method for the manufacture of concrete test blocks for joint sealant bond
testing.
The requirements of this European Standard are applicable to concrete test blocks with a maximum aggregate size of 16 mm to 20 mm or with a maximum aggregate size of 4,0 mm.

Heiß verarbeitbare Fugenmassen - Teil 12: Prüfverfahren zur Herstellung von Beton-Grundkörpern für die Bestimmung des Dehn- und Haftvermögens

Diese Europäische Norm beschreibt ein Verfahren zur Herstellung von Beton-Probekörpern für die Prüfung des Haft- und Dehnvermögens von Fugenmassen.
Die Anforderungen dieser Europäischen Norm gelten für Beton-Probekörper mit einer maximalen Korngröße der Gesteinskörnungen von 16 mm bis 20 mm bzw. von 4 mm.

Produits de scellement de joints appliqués a chaud - Partie 12 : Méthode d'essai pour la fabrication de blocs en béton pour l'essai d'adhérence (composition)

Cette Norme européenne décrit une méthode pour la fabrication de blocs en béton pour l'essai d'adhérence des produits de scellement de joints.
Les exigences de cette Norme européenne s'appliquent aux blocs d'essai en béton avec une dimension de gravillons maximale de 16 mm a 20 mm ou une dimension de granulat maximale de 4,0 mm.

Hot applied joint sealants - Part 12: Test method for the manufacture of concrete test blocks for bond testing (recipe methods)

General Information

• Status: Published
• Publication Date: 31-May-2004
• ICS: 91.100.50 - Binders. Sealing materials
• ICS: 93.080.20 - Road construction materials
• Technical Committee: CES - Roads
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 01-Jun-2004
• Due Date: 01-Jun-2004
• Completion Date: 01-Jun-2004
• Directive: 89/106/EEC - Construction products
• Ref Project: EN 13880-12:2003 - Hot applied joint sealants - Part 12: Test method for the manufacture of concrete test blocks for bond testing (recipe methods)

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Hot applied joint sealants - Part 12: Test method for the manufacture of concrete test blocks for bond testing (recipe methods)Heiß verarbeitbare Fugenmassen - Teil 12: Prüfverfahren zur Herstellung von Beton-Grundkörpern für die Bestimmung des Dehn- und HaftvermögensProduits de scellement de joints appliqués a chaud - Partie 12 : Méthode d'essai pour la fabrication de blocs en béton pour l'essai d'adhérence (composition)Hot applied joint sealants - Part 12: Test method for the manufacture of concrete test blocks for bond testing (recipe methods)93.080.20Materiali za gradnjo cestRoad construction materials91.100.50Veziva. Tesnilni materialiBinders. Sealing materialsICS:Ta slovenski standard je istoveten z:EN 13880-12:2003SIST EN 13880-12:2004en01-junij-2004SIST EN 13880-12:2004SLOVENSKI
STANDARD



SIST EN 13880-12:2004



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13880-12August 2003ICS 93.080.20English versionHot applied joint sealants - Part 12: Test method for themanufacture of concrete test blocks for bond testing (recipemethods)Produits de scellement de joints appliqués à chaud - Partie12: Méthode d'essai pour la fabrication de blocs en bétonpour l'essai d'adhérence (recette)Heiß verarbeitbare Fugenmassen - Teil 12: Prüfverfahrenzur Herstellung von Beton-Grundkörpern für dieBestimmung des Dehn- und HaftvermögensThis European Standard was approved by CEN on 2 May 2003.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and UnitedKingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2003 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13880-12:2003 ESIST EN 13880-12:2004



EN 13880-12:2003 (E)2ContentspageForeword.31Scope.32Normative references.43Principle.44Apparatus.45Materials.55.1Coarse aggregate.55.2Fine aggregate.55.3Cement.55.4Mixing water.55.5Admixtures.56Concrete test block mixes.66.1General.66.2Concrete test blocks with coarse aggregate.66.3Concrete test blocks with fine aggregate.67Manufacture of concrete test blocks.67.1General.67.2Casting.77.3Curing the concrete blocks.77.4Cutting the concrete test blocks.77.5Storage of the concrete test blocks.78Conditioning of the concrete test blocks.79Test report.7Bibliography.8SIST EN 13880-12:2004



EN 13880-12:2003 (E)3ForewordThis document EN 13880-12:2003 has been prepared by Technical Committee CEN/TC 227 “Road materials”, thesecretariat of which is held by DIN.This European Standard shall be given the status of a national standard, either by publication of an identical text orby endorsement, at the latest by February 2004, and conflicting national standards shall be withdrawn at the latestby March 2005.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the followingcountries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal,Slovakia, Spain, Sweden, Switzerland and the United Kingdom.This European Standard is one of a series of standards as listed below:EN 13880-1, Hot applied joint sealants — Part 1: Test method for the determination of density at 25 °C.EN 13880-2, Hot applied joint sealants — Part 2: Test method for the determination of cone penetration at 25 °C.EN 13880-3, Hot applied joint sealants — Part 3: Test method for the determination of penetration and recovery(resilience).EN 13880-4, Hot applied joint selants — Part 4: Test method for the determination of heat resistance — Change inpenetration value.EN 13880-5, Hot applied joint sealants — Part 5: Test method for the determination of flow resistance.prEN 13880-6, Hot applied joint sealants — Part 6: Test method for the preparation of samples for testing.EN 13880-7, Hot applied joint sealants — Part 7: Function testing of joint sealants.EN 13880-8, Hot applied joint sealants — Part 8: Test method for the determination of the change in weight of fuelresistance joint sealants after fuel immersion.EN 13880-9, Hot applied joint sealants — Part 9: Test method for the determination of compatibility with asphaltpavements.EN 13880-10, Hot applied joint sealants — Part 10: Test method for the determination of adhesion and cohesionfollowing continuous extension and compression.EN 13880-11, Hot applied joint sealants — Part 11: Test method for the preparation of asphalt test bl
...