SIST EN 60811-513:2012

Electric and optical fibre cables - Test methods for non-metallic materials - Part 513: Mechanical tests - Methods specific to polyethylene and polypropylene compounds - Wrapping test after conditioning

This Part 513 of IEC 60811 gives procedures for a wrapping test after conditioning at elevated temperature. This test method applies specifically to polyethylene and polypropylene insulation. This test is intended for samples from filled cables of polyolefin insulation having a wall thickness of less than or equal to 0,8 mm.

Kabel, isolierte Leitungen und Glasfaserkabel - Prüfverfahren für nichtmetallene Werkstoffe - Teil 513: Mechanische Prüfungen - Verfahren speziell für Polyethylen- und Polypropylenmischungen - Wickelprüfung nach Vorbehandlung

Câbles électriques et câbles à fibres optiques - Méthodes d'essai pour les matériaux non-métalliques - Partie 513: Essais mécaniques - Méthodes spécifiques aux mélanges de polyéthylène et de polypropylène - Essai d'enroulement après conditionnement

La CEI 60811-513:2012 décrit la procédure à suivre pour réaliser un essai d'enroulement après conditionnement à température élevée. Cette méthode d'essai s'applique spécifiquement aux enveloppes isolantes en polyéthylène et polypropylène. Cet essai s'applique aux enveloppes isolantes à base de polyoléfines des câbles remplis ayant une épaisseur de paroi inférieure ou égale à 0,8 mm. La CEI 60811-513:2012 annule et remplace l'Article 9 de la CEI 60811-4-2:2004, qui est supprimée. L'ensemble des informations relatives aux remplacements figure dans l'Annexe A de la CEI 60811-100:2012. Aucune modification technique n'a été effectuée par rapport à l'édition précédente; voir cependant l'avant-propos de la CEI 60811-100:2012.   Cette publication doit être lue conjointement avec la CEI 60811-100:2012.

Električni in optični kabli - Preskuševalne metode za nekovinske materiale - 513. del: Specifične metode za polietilenske in polipropilenske zmesi - Preskus z ovijanjem po kondicioniranju

513. del standarda IEC 60811 navaja postopke za preskus z ovijanjem po kondicioniranju pri povišani temperaturi. Ta preskusna metoda je specifična za polietilensko in polipropilensko izolacijo. Ta preskus je predviden za vzorce poliolefinske izolacije iz polnjenih kablov, katere stena je debela največ 0,8 mm.

General Information

• Status: Published
• Publication Date: 08-Jul-2012
• ICS: 29.035.20 - Plastics and rubber insulating materials
• ICS: 29.060.20 - Cables
• Technical Committee: IEKA - Electric cables
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 19-Jun-2012
• Due Date: 24-Aug-2012
• Completion Date: 09-Jul-2012
• Directive: 2006/95/EC - Directive 2006/95/EC of the European Parliament and of the Council of 12 December 2006 on the harmonisation of the laws of Member States relating to electrical equipment designed for use within certain voltage limits (codified version)
• Directive: 2014/35/EU - Directive 2014/35/EU of the European Parliament and of the Council of 26 February 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of electrical equipment designed for use within certain voltage limits
• Ref Project: EN 60811-513:2012 - Electric and optical fibre cables - Test methods for non-metallic materials - Part 513: Mechanical tests - Methods specific to polyethylene and polypropylene compounds - Wrapping test after conditioning

Relations

• Replaces: SIST EN 60811-4-2:2005 - Insulating and sheathing materials of electric and optical cables - Common test methods -- Part 4-2: Methods specific to polyethylene and polypropylene compounds - Tensile strength and elongation at break after conditioning at elevated temperature - Wrapping test after conditioning at elevated temperature - Wrapping test after thermal ageing in air - Measurement of mass increase - Long-term stability test - Test method for copper-catalyzed oxidative degradation
• Effective Date: 29-Jan-2023
• Revised: SIST EN 60811-4-2:2005 - Insulating and sheathing materials of electric and optical cables - Common test methods -- Part 4-2: Methods specific to polyethylene and polypropylene compounds - Tensile strength and elongation at break after conditioning at elevated temperature - Wrapping test after conditioning at elevated temperature - Wrapping test after thermal ageing in air - Measurement of mass increase - Long-term stability test - Test method for copper-catalyzed oxidative degradation
• Effective Date: 23-Jul-2014
• Revised: SIST EN 60811-4-2:2005 - Insulating and sheathing materials of electric and optical cables - Common test methods -- Part 4-2: Methods specific to polyethylene and polypropylene compounds - Tensile strength and elongation at break after conditioning at elevated temperature - Wrapping test after conditioning at elevated temperature - Wrapping test after thermal ageing in air - Measurement of mass increase - Long-term stability test - Test method for copper-catalyzed oxidative degradation
• Effective Date: 07-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60811-513:2012
01-september-2012
(OHNWULþQLLQRSWLþQLNDEOL3UHVNXãHYDOQHPHWRGH]DQHNRYLQVNHPDWHULDOH
GHO6SHFLILþQHPHWRGH]DSROLHWLOHQVNHLQSROLSURSLOHQVNH]PHVL3UHVNXV]
RYLMDQMHPSRNRQGLFLRQLUDQMX
Electric and optical fibre cables - Test methods for non-metallic materials - Part 513:
Mechanical tests - Methods specific to polyethylene and polypropylene compounds -
Wrapping test after conditioning
Kabel, isolierte Leitungen und Glasfaserkabel - Prüfverfahren für nichtmetallene
Werkstoffe - Teil 513: Mechanische Prüfungen - Verfahren speziell für Polyethylen- und
Polypropylenmischungen - Wickelprüfung nach Vorbehandlung
Câbles électriques et câbles à fibres optiques - Méthodes d'essai pour les matériaux non
-métalliques - Partie 513: Essais mécaniques - Méthodes spécifiques aux mélanges de
polyéthylène et de polypropylène - Essai d'enroulement après conditionnement
Ta slovenski standard je istoveten z: EN 60811-513:2012
ICS:
29.035.20 3ODVWLþQLLQJXPHQLL]RODFLMVNL Plastics and rubber insulating
PDWHULDOL materials
29.060.20 Kabli Cables
SIST EN 60811-513:2012 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60811-513:2012

---------------------- Page: 2 ----------------------

SIST EN 60811-513:2012

EUROPEAN STANDARD
EN 60811-513

NORME EUROPÉENNE
June 2012
EUROPÄISCHE NORM

ICS 29.035.01; 29.060.20 Supersedes EN 60811-4-2:2004 (partially)


English version


Electric and optical fibre cables -
Test methods for non-metallic materials -
Part 513: Mechanical tests -
Methods specific to polyethylene and polypropylene compounds -
Wrapping test after conditioning
(IEC 60811-513:2012)

Câbles électriques et à fibres optiques -  Kabel, isolierte Leitungen
Méthodes d'essai pour les matériaux und Glasfaserkabel -
non-métalliques - Prüfverfahren für nichtmetallene
Partie 513: Essais mécaniques - Werkstoffe -
Méthodes spécifiques pour les mélanges Teil 513: Mechanische Prüfungen -
polyéthylène et polypropylène - Verfahren speziell für Polyethylen- und
Essai d'enroulement après Polypropylenmischungen -
conditionnement Wickelprüfung nach Vorbehandlung
(CEI 60811-513:2012) (IEC 60811-513:2012)


This European Standard was approved by CENELEC on 2012-04-17. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland, Turkey and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels


© 2012 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60811-513:2012 E

---------------------- Page: 3 ----------------------

SIST EN 60811-513:2012
EN 60811-513:2012 - 2 -
Foreword
The text of document 20/1309/FDIS, future edition 1 of IEC 60811-513, prepared by IEC/TC 20
"Electric cables" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
EN 60811-513:2012.
The following dates are fixed:
(dop) 2013-01-17
• latest date by which the document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2015-04-17
• latest date by which the national
standards conflicting with the
document have to be withdrawn

This document supersedes Clause 9 of EN 60811-4-2:2004 (partially). Full details of the replacements
are shown in Annex A of EN 60811-100:2012.
There are no specific technical changes with respect to EN 60811-4-2:2004, but see the Foreword to
EN 60811-100:2012.

This standard is to be read in conjunction with EN 60811-100.

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.

This standard covers the Principle Elements of the Safety Objectives for Electrical Equipment
Designed for Use within Certain Voltage Limits (LVD - 2006/95/EC).

Endorsement notice
The text of the International Standard IEC 60811-513:2012 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:

IEC 60811-4-2:2004 NOTE Harmonized as EN 60811-4-2:2004 (not modified).
IEC 60811-601 NOTE Harmonized as EN 60811-601.

---------------------- Page: 4 ----------------------

SIST EN 60811-513:2012
- 3 - EN 60811-513:2012
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.

Publication Year Title EN/HD Year
IEC 60811-100 2012 Electric and optical fibre cables - Test EN 60811-100 2012
methods for non-metallic materials -
Part 100: General

---------------------- Page: 5 ----------------------

SIST EN 60811-513:2012

---------------------- Page: 6 ----------------------

SIST EN 60811-513:2012



IEC 60811-513

®


Edition 1.0 2012-03




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE











Electric and optical fibre cables – Test methods for non-metallic materials –

Part 513: Mechanical tests – Methods specific to polyethylene and

polypropylene compounds – Wrapping test after conditioning




Câbles électriques et à fibres optiques – Méthodes d’essai pour les matériaux

non-métalliques –


Partie 513: Essais mécaniques – Méthodes spécifiques pour les mélanges

polyéthylène et polypropylène – Essai d’enroulement après conditionnement












INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE

PRICE CODE
INTERNATIONALE

CODE PRIX H


ICS 29.035.01; 29.060.20 ISBN 978-2-88912-992-8



Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN 60811-513:2012
– 2 – 60811-513  IEC:2012
CONTENTS
FOREWORD . 3
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Test method . 6
4.1 General . 6
4.2 Conditioning procedure . 6
4.3 Test procedure . 7
4.4 Evaluation of results . 7
5 Test report. 7
Bibliography . 8

---------------------- Page: 8 ----------------------

SIST EN 60811-513:2012
60811-513  IEC:2012 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

ELECTRIC AND OPTICAL FIBRE CABLES –
TEST METHODS FOR NON-METALLIC MATERIALS –

Part 513: Mechanical tests –
Methods specific to polyethylene and polypropylene compounds –
Wrapping test after conditioning


FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international c
...