iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 60688:1995

(Main)

Electrical measuring transducers for converting a.c. electrical quantities to analogue or digital signals

Electrical measuring transducers for converting a.c. electrical quantities to analogue or digital signals

Applies to transducers with electrical inputs and outputs for making measurements of a.c. electrical quantities with a nominal frequency between 5 Hz and 1 500 Hz. The output signal may be in the form of an analogue direct current or in digital form. Supersedes IEC 688-1 and IEC 688-2.

Elektrische Messumformer zur Umwandlung von Wechselstromgrößen in analoge oder digitale Signale

Transducteurs électriques de mesure convertissant les grandeurs électriques alternatives en signaux analogiques ou numériques

S'applique aux transducteurs à grandeurs d'entrées et de sorties électriques, destinés à mesurer des grandeurs électriques alternatives d'une fréquence nominale comprise entre 5 Hz et 1 500 Hz. Le signal de sortie peut être sous la forme de courant continu analogique ou sous la forme numérique. Remplace la CEI 688-1 (1980) et CEI 688-2 (1988).

Električni merilni pretvorniki za pretvarjanje izmeničnih električnih veličin v analogne ali digitalne signale (IEC 60688:1992)

General Information

Status
Withdrawn
Publication Date
31-Jul-1995
Withdrawal Date
08-Nov-2015
ICS
17.220.20 - Measurement of electrical and magnetic quantities
Technical Committee
MOV - Measuring equipment for electromagnetic quantities
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
09-Nov-2015
Due Date
02-Dec-2015
Completion Date
09-Nov-2015
Ref Project
EN 60688:1992 - Electrical measuring transducers for converting a.c. electrical quantities to analogue or digital signals

Relations

Amended By
SIST EN 60688:1995/A1:2001 - Electrical measuring transducers for converting a.c. electrical quantities to analogue or digital signals
Effective Date
21-Sep-2010
Amended By
SIST EN 60688:1995/A2:2002 - Electrical measuring transducers for converting a.c. electrical quantities to analogue or digital signals
Effective Date
21-Sep-2010
Amended By
SIST EN 60688:1995/A1:2001 - Electrical measuring transducers for converting a.c. electrical quantities to analogue or digital signals
Effective Date
29-Jan-2023
Amended By
SIST EN 60688:1995/A2:2002 - Electrical measuring transducers for converting a.c. electrical quantities to analogue or digital signals
Effective Date
29-Jan-2023
Revised
SIST EN 60688:2013 - Electrical measuring transducers for converting a.c. electrical quantities to analogue or digital signals (IEC 60688:2012)
Effective Date
06-May-2014
Amended By
SIST EN 60688:1995/A2:2002 - Electrical measuring transducers for converting a.c. electrical quantities to analogue or digital signals
Effective Date
07-Jun-2022
Amended By
SIST EN 60688:1995/A1:2001 - Electrical measuring transducers for converting a.c. electrical quantities to analogue or digital signals
Effective Date
07-Jun-2022
Replaced By
SIST EN 60688:2013 - Electrical measuring transducers for converting a.c. electrical quantities to analogue or digital signals (IEC 60688:2012)
Effective Date
01-Mar-2013
Replaced By
SIST EN 60688:2013 - Electrical measuring transducers for converting a.c. electrical quantities to analogue or digital signals (IEC 60688:2012)
Effective Date
28-Jan-2023

Buy Standard

EN 60688:1995EN 60688:1995
PreviousNext
Standard
EN 60688:1995
English language
39 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60688:1995
01-avgust-1995
(OHNWULþQLPHULOQLSUHWYRUQLNL]DSUHWYDUMDQMHL]PHQLþQLKHOHNWULþQLKYHOLþLQY
DQDORJQHDOLGLJLWDOQHVLJQDOH ,(&
Electrical measuring transducers for converting a.c. electrical quantities to analogue or
digital signals
Elektrische Messumformer zur Umwandlung von Wechselstromgrößen in analoge oder
digitale Signale
Transducteurs électriques de mesure convertissant les grandeurs électriques
alternatives en signaux analogiques ou numériques
Ta slovenski standard je istoveten z: EN 60688:1992
ICS:
17.220.20 0HUMHQMHHOHNWULþQLKLQ Measurement of electrical
PDJQHWQLKYHOLþLQ and magnetic quantities
SIST EN 60688:1995 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60688:1995

---------------------- Page: 2 ----------------------

SIST EN 60688:1995

---------------------- Page: 3 ----------------------

SIST EN 60688:1995

---------------------- Page: 4 ----------------------

SIST EN 60688:1995

---------------------- Page: 5 ----------------------

SIST EN 60688:1995

---------------------- Page: 6 ----------------------

SIST EN 60688:1995

---------------------- Page: 7 ----------------------

SIST EN 60688:1995

---------------------- Page: 8 ----------------------

SIST EN 60688:1995

---------------------- Page: 9 ----------------------

SIST EN 60688:1995

---------------------- Page: 10 ----------------------

SIST EN 60688:1995

---------------------- Page: 11 ----------------------

SIST EN 60688:1995

---------------------- Page: 12 ----------------------

SIST EN 60688:1995

---------------------- Page: 13 ----------------------

SIST EN 60688:1995

---------------------- Page: 14 ----------------------

SIST EN 60688:1995

---------------------- Page: 15 ----------------------

SIST EN 60688:1995

---------------------- Page: 16 ----------------------

SIST EN 6068
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN IEC 61557-12:2022/AC:2022(Corrigendum)
Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC - Equipment for testing, measuring or monitoring of protective measures - Part 12: Power metering and monitoring devices (PMD) (IEC 61557-12:2018/COR1:2022)
EN IEC 61557-12:2022/AC:2022-09

IEC Corrected Version

  • Corrigendum
    4 pages
    French language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 61557-12:2022/A1:2022/AC:2022(Corrigendum)
Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC - Equipment for testing, measuring or monitoring of protective measures - Part 12: Power metering and monitoring devices (PMD) (IEC 61557-12:2018/A1:2021/COR1:2022)
EN IEC 61557-12:2022/A1:2022/AC:2022-09

IEC Corrected Version

  • Corrigendum
    4 pages
    French language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 61557-3:2022(Main)
Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC - Equipment for testing, measuring or monitoring of protective measures - Part 3: Loop impedance (IEC 61557-3:2019)
EN IEC 61557-3:2022

This part of IEC 61557 specifies the requirements applicable to equipment for measuring the
loop impedance between a line conductor and protective conductor; between a line conductor
and neutral; or between two line conductors by using the voltage drop when the circuit under
test is loaded.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 60477-2:2022(Main)
Laboratory resistors - Part 2: Laboratory AC resistors (IEC 60477-2:2022)
EN IEC 60477-2:2022

This part of IEC 60477 applies to resistors intended as laboratory AC resistors for use over a range of frequencies from DC up to a stated frequency which is not in excess of 1 MHz. Such resistors are hereinafter referred to as "AC resistors".
In addition to satisfying the requirements of IEC 60477, resistors satisfying the requirements of this standard are designed to have a small variation of resistance and a small phase displacement over the stated frequency range.
Because of the uncertainties in AC properties which can result from stray inductances, stray capacitances, eddy currents, dielectric absorption effects and skin effect, the AC resistors to which this standard applies are classified according to their construction (see Annex D), as follows:
a) Two-terminal resistor which each of one terminal both for current and potential;
b) Three-terminal resistor which has one more shield terminal (also could be called as guard terminal) connected to the electric screen than the two-terminal resistor to reduce the stray capacitances effect;
c) Four-terminal resistor which has independent current terminals and potential terminals to reduce the stray inductances and contact resistances;
d) Five-terminal resistor which has one more shield terminal than the four-terminal resistor;
e) Four-terminal coaxial resistor which has two terminal-pairs with the outer shield conductors working as the low terminal of current or potential;
f) Two-terminal-pair resistor which has two terminal-pairs with the outer shield conductors working as the return path for the signal current (not grounded);
g) Four-terminal-pair resistor which has four terminal-pairs with the outer shield conductors working as the return path for the signal current (not grounded) to eliminate the effect of mutual coupling between the current and potential leads.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 60477-1:2022(Main)
Laboratory resistors - Part 1: Laboratory DC resistors (IEC 60477-1:2022)
EN IEC 60477-1:2022

This document applies to resistors intended for use as laboratory DC resistors (hereinafter
referred to as "resistors") comprising standard resistors, single or multiple resistors of accuracy
Classes 0,000 05 to 10 and single or multi-dial resistors of accuracy Classes 0,000 5 to 10.
This document does not apply to:
1) resistors which are intended for use solely as permanently mounted circuit components,
2) resistors used on alternating current or on pulsed current,
3) active resistors,
4) series resistors and shunts which are considered as accessories of electrical measuring
instruments in the relevant IEC document (examples of these are as follows).
EXAMPLE 1 IEC 60051 series: Recommendations for direct acting indicating analogue electrical measuring
instruments and their accessories.
EXAMPLE 2 IEC 60258: Direct acting recording electrical measuring instruments and their accessories.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 61557-7:2022(Main)
Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. - Equipment for testing, measuring or monitoring of protective measures - Part 7: Phase sequence (IEC 61557-7:2019)
EN IEC 61557-7:2022

This part of IEC 61557 specifies the requirements applicable to measuring equipment for
testing the phase sequence in three-phase distribution systems. Indication of the phase
sequence can be mechanical, visual and/or audible.
This document does not apply to additional measurements for other quantities. It does not
apply to monitoring relays.
NOTE Common worldwide three-phase distribution systems are depicted in IEC 61010-1.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 61557-1:2022(Main)
Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC - Equipment for testing, measuring or monitoring of protective measures - Part 1: General requirements (IEC 61557-1:2019)
EN IEC 61557-1:2021

This part of IEC 61557 specifies the general requirements applicable to measuring and
monitoring equipment for testing the electrical safety in low-voltage distribution systems with
nominal voltages up to 1 000 V AC and 1 500 V DC.
When measuring equipment or measuring installations involve measurement tasks of various
measuring equipment covered by this series of standards, then the part of this series relevant
to each of the measurement tasks is applicable.
NOTE The term "measuring equipment" will hereafter be used to designate "testing, measuring and monitoring
equipment".
Other parts of IEC 61557 can specify additional requirements or deviations.
This document does not cover functional safety or cybersecurity

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 61557-4:2022(Main)
Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC - Equipment for testing, measuring or monitoring of protective measures - Part 4: Resistance of earth connection and equipotential bonding (IEC 61557-4:2019)
EN IEC 61557-4:2021

This part of IEC 61557 specifies the requirements applicable to equipment for measuring the
resistance of earth conductors, protective earth conductors and conductors for equipotential
bonding, including their connections and terminals, with an indication of the measured value
or an indication of the limits.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 61557-12:2022/A1:2022(Amendment)
Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC - Equipment for testing, measuring or monitoring of protective measures - Part 12: Power metering and monitoring devices (PMD) (IEC 61557-12:2018/A1:2021)
EN IEC 61557-12:2022/A1:2022

This part of IEC 61557 specifies requirements for power metering and monitoring devices (PMD) that measure and monitor the electrical quantities within electrical distribution systems, and optionally other external signals. These requirements also defin the performance of PMD in single- and three-phace AC or DC systems having rated voltages up to 1000 V AC or up to 1500 V DC.
These devices are fixed or portable. They are intended to be used indoors and/or outdoors.
Power metering and monitoring devices  (PMD), as defined in this document, give additional safety information, which aids the verification of the installation and enhances the performance of the distribution systems.
Additionally, this document specifies requirements for measurement functions dedicated to metering and monitoring of electrical parameters called power metering and monitoring function (PMF) which can be embedded in equipment (EMPF) that is not classified as PMD and for which the main function is not power metering and monitoring.
Requirements for power metering and monitoring function (PMF) and additional requirements for equipments embedding power metering and monitoring function (EPMF) are described in Annex H.
The power metering and monitoring devices (PMD) for electrical parameters described in this document are used for general industrial and commercial applications.
This document does not address functional safety and cyber security aspects.
This document is not applicable to:
- electricity metering equipment that complies with IEC 62053-21, IEC 62053-22, IEC 62053-23 and IEC 62053-24. Nevertheless, uncertainties defined in this document for active and reactive energy measurement are derived from those defined in IEC 62053 (all parts);
- the measurement and monitoring of electrical parameters defined in IEC 61557-2 to IEC 61557-9 and IEC 61557-13 or in IEC 62020;
- power quality instrument (PQI) according IEC 62586 (all parts);
- devices covered by IEC 60051 (all parts) (direct acting analogue electrical measuring instrument).
Note 1 Generally such types of devices are used in the following applications or for the following general needs:
- energy management inside the installation, such as facilitating the implementation of documents such as ISO 50001 and IEC 60364-8-1;
- monitoring and/or measurement of electrical parameters;
- measurement and/or monitoring of the quality of energy inside commercial/industrial installations.
Note 2 A measuring and monitoring device of electrical parameters usually consists of several functional modules. All or some of the functional modules are combined in one device. Examples of fuctnional modules are:
- measurement and monitoring of several electrical parameters simultaneously;
- energy measurement and/or monitoring, as well as sometimes compliance with aspects of building regulations;
- alarms functions;
- demand side quality (current and voltage harmonics, over/under voltages, voltage dips and swells, etc.).
Note 3 PMD are historically called power meter, power monitor, power monitor device, power energy monitoring device, power analyser, multifunction meter, measuring multifunction equipment, energe meters.
Note 4 Metering, measuring and monitoring applications are explained in Annex A.

  • Amendment
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 61557-5:2022(Main)
Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC - Equipment for testing, measuring or monitoring of protective measures - Part 5: Resistance to earth (IEC 61557-5:2019)
EN IEC 61557-5:2021

This part of IEC 61557 specifies the requirements applicable to measuring equipment for measuring the resistance to earth using an AC voltage.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day