SIST EN 13445-3:2014/oprA12:2017

Unfired pressure vessels - Part 3: Design

Amends subclause 6.1.3 and Table 6.1

Unbefeuerte Druckbehälter - Teil 3: Konstruktion

Dieser Teil 3 der Europäischen Norm legt die Anforderungen an die Konstruktion von unbefeuerten Druckbehältern
nach EN 13445-1:2014 und hergestellt aus Stählen nach EN 13445-2:2014 fest.
EN 13445-5:2014 gibt im Anhang C Bedingungen für die Konstruktion von Zugangs- und Besichtigungsöffnungen,
von Verschlüssen und besonderen Verschlusselementen.
ANMERKUNG Dieser Teil gilt für Konstruktion und Berechnung von Behältern vor der Inbetriebnahme. Er kann auch, mit
entsprechenden Anpassungen, für Berechnungen oder analytische Nachweise im Betrieb verwendet werden.

Récipients sous pression non soumis à la flamme - Partie 3 : Conception

Cette partie de la présente norme européenne spécifie les exigences relatives à la conception des récipients sous
pression non soumis à la flamme couverts par l’EN 13445-1:2014 et construits en aciers conformes à
l’EN 13445-2:2014.
L’Annexe C de l’EN 13445-5:2014 spécifie les exigences relatives à la conception des ouvertures d’accès et
d’inspection, des mécanismes de fermeture et des éléments de verrouillage spéciaux.
NOTE Cette partie s'applique à la conception des récipients avant mise en service. Elle peut être utilisée pour les calculs
ou l'analyse en service sous réserve d'apporter les ajustements appropriés.

Nekurjene tlačne posode - 3. del: Konstruiranje - Dopolnilo A12

General Information

• Status: Not Published
• Public Enquiry End Date: 09-Aug-2017
• ICS: 23.020.32 - Pressure vessels
• Technical Committee: TLP - Pressure vessels
• Current Stage: 98 - Abandoned project (Adopted Project)
• Start Date: 06-Oct-2022
• Due Date: 11-Oct-2022
• Completion Date: 06-Oct-2022
• Directive: 2014/68/EU - Directive 2014/68/EU of the European Parliament and of the Council of 15 May 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of pressure equipment
• Mandate: M/071 - Mandate to CEN for standardization in the field of Pressure equipment
• Ref Project: EN 13445-3:2014/prA12 - Unfired pressure vessels - Part 3: Design

Relations

• Amends: SIST EN 13445-3:2014 - Unfired pressure vessels - Part 3: Design
• Effective Date: 01-Jul-2017

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 13445-3:2014/oprA12:2017
01-julij-2017
1HRJUHYDQHQHNXUMHQHWODþQHSRVRGHGHO.RQVWUXLUDQMH'RSROQLOR$
Unfired pressure vessels - Part 3: Design
Unbefeuerte Druckbehälter - Teil 3: Konstruktion
Récipients sous pression non soumis à la flamme - Partie 3 : Conception
Ta slovenski standard je istoveten z: EN 13445-3:2014/prA12
ICS:
23.020.32 7ODþQHSRVRGH Pressure vessels
SIST EN 13445-3:2014/oprA12:2017 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 13445-3:2014/oprA12:2017

---------------------- Page: 2 ----------------------

SIST EN 13445-3:2014/oprA12:2017


DRAFT
EUROPEAN STANDARD
EN 13445-3:2014
NORME EUROPÉENNE

EUROPÄISCHE NORM
prA12
June 2017
ICS 23.020.30
English Version

Unfired pressure vessels - Part 3: Design
Récipients sous pression non soumis à la flamme - Unbefeuerte Druckbehälter - Teil 3: Konstruktion
Partie 3 : Conception
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 54.

This draft amendment A12, if approved, will modify the European Standard EN 13445-3:2014. If this draft becomes an
amendment, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for
inclusion of this amendment into the relevant national standard without any alteration.

This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. I
...