SIST EN 14035-19:2003/AC:2006
(Amendment)Fireworks - Part 19: Hand-held sparklers - Specification and test methods
Fireworks - Part 19: Hand-held sparklers - Specification and test methods
TC - Various modifications throughout text
Feuerwerkskörper - Teil 19: Wunderkerzen - Anforderungen und Prüfverfahren
Artifices de divertissement - Partie 19: Cierges magiques tenus a la main - Spécifications et méthodes d'essai
Ognjemet – 19. del: Čudežne svečke - ročne – Specifikacija in preskusne metode
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Fireworks - Part 19: Hand-held sparklers - Specification and test methodsArtifices de divertissement - Partie 19: Cierges magiques tenus a la main - Spécifications et méthodes d'essaiFeuerwerkskörper - Teil 19: Wunderkerzen - Anforderungen und PrüfverfahrenTa slovenski standard je istoveten z:EN 14035-19:2003/AC:2006SIST EN 14035-19:2003/AC:2006en,de71.100.30ICS:SLOVENSKI
STANDARDSIST EN 14035-19:2003/AC:200601-september-2006
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 14035-19:2003/ACMay 2006Mai 2006Mai 2006ICS 71.100.30English versionVersion FrançaiseDeutsche FassungFireworks - Part 19: Hand-held sparklers - Specification and test methodsArtifices de divertissement - Partie 19:Cierges magiques tenus à la main -Spécifications et méthodes d'essaiFeuerwerkskörper - Teil 19: Wunderkerzen- Anforderungen und PrüfverfahrenThis corrigendum becomes effective on 24 May 2006 for incorporation in the three official languageversions of the EN.Ce corrigendum prendra effet le 24 mai 2006 pour incorporation dans les trois versions linguistiquesofficielles de la EN.Die Berichtigung tritt am 24.Mai 2006 zur Einarbeitung in die drei offiziellen Sprachfassungen der ENin Kraft.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2006 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members.Tous droits d'exploitation sous quelque forme et de quelque manière que ce soit réservés dans le monde entier auxmembres nationaux du CEN.Alle Rechte der Verwertung, gleich in welcher Form und in welchem Verfahren, sind weltweit den nationalen Mitgliedernvon CEN vorbehalten.Ref. No.:EN 14035-19:2003/AC:2006 D/E/F
EN 14035-19:2003/AC:2006 (E/F/D) 2 English version
Foreword
Replace ‘prEN 14035-5, Fireworks – Part 5: Batteries or combinations – Specification and test methods’ by ‘EN 14035-5, Fireworks – Part 5: Batteries and combinations – Specification and test methods’.
‘prEN 14035-31, Fireworks – Part 31: Shells-in-mortars – Specification and test methods’ by ‘prEN 14035-31, Fireworks – Part 31: Shell-in-mortars – Specification and test methods’.
Delete:
prEN 14035-14, Fireworks – Part 14: Flying squibs – Specification and test methods prEN 14035-16, Fireworks – Part 16: Friction ignited flash bangers – Specification and test methods prEN 14035-26, Fireworks – Part 26: Percussion caps – Specification and test methods prEN 14035-32, Fireworks – Part 32: Snaps – Specification and test methods
Add: EN 14035-38, Fireworks – Part 38: Shot tubes – Specification and test methods
1 Scope
brief description Replace: ’….rigid wire partially coated with slow-burning pyrotechnic composition, with or without an ignition tip and designed to be held in the hand;…’ by ‘….rigid wire partially coated along one end with slow-burning pyrotechnic composition, with or without an ignition tip and designed to be held in the hand….’
2
Normative references
Replace “ISO 2439, Flexible cellular polymeric materials – Determination of hardness (indentation technique) (including Technical Corrigendum 1:2001)” by “EN ISO 2439, Flexible cellular polymeric materials - Determination of hardness (indentation technique) (ISO 2439:1997, including Technical Corrigendum 1:1998)
8.1 Length of hand-held sparkler (type test and batch test)
Add (an alternative procedure and corresponding apparatus):
'8.1.1 Apparatus Rack, comprising a board with raised strips (at least 10 mm thick) along three edges, supported in a plane inclined at 30° to the horizontal, capable of holding at least ten hand-held sparklers side-by-side. The board shall be marked with lines parallel to the bottom edge to indicate the maximum total length and the minimum handle length for the sparklers under test, as specified in 4.1 (for example, (300 ± 1) mm for the total length and (75 ± 1) mm for the handle length, respectively, for category 1 sparklers). An example of a suitable rack (for category 1 sparklers) is shown in Figure 1. For category 2 hand-held sparklers the rack shall be marked with two lines ((450 ± 1) mm and (700 ± 1 mm)) for the total lengths and two lines ((75 ± 1) mm and (150 ± 1 mm)) for the corresponding handle lengths.
EN 14035-19:2003/AC:2006 (E/F/D) 3
Figure 1 – Example of a rack for measuring category 1 sparklers
NOTE The alignment of the sparklers in the rack may be aided by means of individual V-shaped grooves cut into the board, running at 90 ° to the bottom edge.
8.1.2 Procedure Record the total numbers of measured sparklers. Measure the length of the sparklers and the handles. Place the sparklers in the rack (8.1.1) in a single layer, with their axes at 90 ° to the bottom edge, as shown in figure 1. Record for each hand-held sparkler whether the total length exceeds a total length of 300 mm for category 1 or 750 mm for category 2. For each hand-held sparkler record, whether the
'handle' length (the length of the wire not coated with pyrotechnic composition) was less than 75 mm for category 1 sparklers and for category 2 sparklers with a total length not exceeding 450 mm, or whether the 'handle' length less than 150 mm for category 2 sparklers with a total length greater than 450 mm. Repeat this process, as necessary, for all the sparklers to be measured.'
8.3.2 Procedure
Line 2 Replace: ‘as shown in Figure 1’ by ‘as shown in Figure 2’
EN 14035-19:2003/AC:2006 (E/F/D) 4 Replace: ‘Figure 1 – Measurement of droop’ by ‘Figure 2 – Measurement of droop’
8.4 Labelling (type test and batch test)
Replace: 'Check conformity to 7.6.2 for example by comparing the type sizes on the actual label with a transparent copy made from Figure 2. Record whether the type sizes were correct'.
by 'Check conformity to 7.6.2, for example by comparing the type sizes on the actual label with a transparent copy made from Figure 3 (for the empty frame, use the inside). Record whether the type sizes are correct'.
Replace: 2,8 mm: ABC abc XYZ xyz 123 2,1 mm: ABC abc XYZ xyz 123
by
2,8 mm:
ABC abc XYZ xyz 123
2,1 mm:
ABC abc XYZ xyz 123
Figure title Replace: ‘Figure 2 – Type sizes of print’ by ‘Figure 3 – Type sizes of print’
A.5.1.2 Cellular rubber sheet
Replace: 'ISO 2439' by 'EN ISO 2439'
A.5.2.1 Conditioning.
Last line, replace “Continue running the machine for 2 h” by “Continue running the machine for 1 h”.
A.5.2.2 Collection of loose pyrotechnic composition
First line, replace “At the end of the 2 h period….” by “At the end of the 1 h period.”
A.7 Test report
Replace: ‘The test report shall include at least the following information, with items i) to j) and l) to r) being given for each hand-held sparkler tested:'
by ‘The test report shall include at least the following information, with items l) to r) being given for each hand-held sparkler tested:'
Replace (only in case the alternative procedure is applied): 'i) * the total length of the hand-held sparkler, in millimetres
and
for category 1 hand-held sparklers, whether the total length was more than 300 mm or
for category 2 hand-held sparklers whether the total length was mote than 750 mm;' by 'i) * for category 1 hand-held sparklers, whether the total length was more than 300 mm,
or for category 2 hand-held sparklers, more than 750 mm;’
EN 14035-19:2003/AC:2006 (E/F/D) 5 Replace (only in case the alternative procedure is applied): 'j) * the handle length, in millimetres
and
for category 1 hand-held sparklers, whether the minimum handle length was at least 75 mm or for category 2 hand-held sparklers, whether the minimum handle length was at least 75 mm when the total length of the hand-held sparkler was not more than 450 mm or at least 150 mm when the total length of the hand-held sparkler was more than 450 mm;'
by 'j) * for category 1 hand-held sparklers and category 2 hand-held sparklers with a total
length of not more than 450 mm, whether the handle length was less than 75 mm, or
for category 2 hand-held sparklers with a total length of more than 450 mm, whether
the handle-length was less than 150 mm;'
B.6.1 General
Replace: 'B.6.4’ by ‘B.6.5’
B.6.3 Critical nonconforming units
Replace ‘Acceptance Quality Level (AQL)’ by ‘acceptance quality limit (AQL)’
Annex D
Add:
A-deviation France France(Arrêté du 1er juillet 1991 portant approbation du Recueil des épreuves d'agrément des artifices de divertissement publié au J.O.R.F. du 20 juillet 1991)The duration of the test for the thermal conditioning shall be 72 h.La durée de l'essai pour le conditionnement thermique est de 72 h.
A-deviation Ireland The basis for applying to the Technical Committee (CEN/TC 212) for an A Deviation is due to the current policy of the Irish Government on the sale of consumer fireworks. On safety and security grounds, the sale of consumer fireworks (of any category) to the general public, is not permitted under current Government policy.
Importation licences can be issued, but only for fireworks used for organised displays, conducted by professional competent operators.
This policy is referenced in the “Guidance Document on Organised Fireworks Displays July 2003” issued by the Irish Government Department of Justice, Equality and Law Reform.
A-deviation Spain R.D. 230/1998 (16/02/1998) Reglamento de Explosivos – Explosives Regulation ITC #8 Catalogación de artificios pirotécnicos – Fireworks cataloguing Compulsory for every item being catalogued mechanical conditioning (2 hours).
A-deviation Switzerland In der Schweiz ist das "Zulassungsverfahren und die technischen Anforderungen für pyrotechnische Gegenstände (Feuerwerk) zum Bundesgesetz vom 25. März 1977 über explosionsgefährlche Stoffe (Sprengstoffgesetz) und dessen Verordnung vom 27. November 2000 (Sprengstoffverordnung) für den Inhalt dieser Norm bindend.
EN 14035-19:2003/AC:2006 (E/F/D) 6 Unterabschnitt Abweichung 4.1 Länge Wunderkerzen der Kategorie II müssen einen Handgriff von mindestens 150 mm haben. 5.1 Art der Anzündung Reibköpfe werden nicht zugelassen. 5.6 Absenkung der Spitze Beim Abbrand von Wunderkerzen der Kategorie I darf die Absenkung der Spitze nicht mehr als 60° von der Waagrechten betragen.
Schalldruckpegel Wunderkerzen der Kategorie I die Knattern oder Knistern dürfen in einer Entfernung von 0,5 Me
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.