F06.80 - Specifications

SCOPE
1.1 This specification covers the requirements for the compound and physical characteristics of bonded rubber crumb floor coverings.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers vinyl composition floor tile with either smooth or embossed surfaces. Vinyl composition tile shall conform to the materials, color, pattern, wearing surface, size, thickness, and squareness indicated in this specification. The material shall be tested for indentation and impact. Performance requirements for vinyl composition tiles include deflection limit, dimensional stability, chemical resistance, and heat resistance. Basic chemicals for chemical resistance test include vinegar, alcohol, mineral oil, sodium hydroxide solution, household ammonia solution, household bleach, olive oil, kerosene, unleaded gasoline, and phenol.
SCOPE
1.1 This specification covers vinyl composition tile (VCT) with either smooth or embossed surfaces for flooring application.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SCOPE
1.1 This specification covers the requirements for the compound and physical characteristics of heterogeneous polyurethane tile or plank flooring that is printed or otherwise decorated to achieve a pattern or visual and protected by a clear wear layer.  
1.2 This specification covers heterogeneous polyurethane tile or plank flooring that shall be composed of binder, fillers, and pigments. The binder shall consist of one or more resins of polyurethane, polyurethane copolymers or other suitable or any desirable combination. Other suitable polymeric resins may be incorporated as part of the binder, provided the polyurethane portion of the binder is greater than 60 % in the base layer.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers floor tiles made of a homogeneous mixture of linoleum cement binder calendered or pressed onto a fibrous or suitable backing for use in commercial, light commercial and residential buildings based on serviceability characteristics. General information and performance characteristics, which determine serviceability and recommended use, are included in this document. The floor coverings shall be of the following types: Type I—linoleum floor tile with fibrous backing; Type II—linoleum floor tile with special backing; Type III—linoleum floor tile without backing; and Type IV—static dissipative linoleum floor tile with or without backing. Materials shall be tested and the individual grades shall conform to specified values of physical properties such as wear surface, size, thickness, and squareness; performance requirements such as residual indentation, static load resistance, flexibility, dimensional stability, resistance to chemicals, resistance to heat, resistance to light, and static dissipation.
SCOPE
1.1 This specification covers floor tiles made of a homogeneous mixture of linoleum cement binder calendered or pressed onto a fibrous or suitable backing. This specification also covers linoleum floor tile without backing.  
1.2 Four types of linoleum floor tile are covered. The floor covering is intended for use in commercial, light commercial, and residential buildings based on serviceability characteristics. General information and performance characteristics, which determine serviceability and recommended use, are included in this document.  
1.3 The following safety hazards caveat pertains only to the test methods portion, Sections 7 and 8, of this specification.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SCOPE
1.1 This specification covers the requirements for the compound and physical characteristics of heterogeneous polyurethane sheet flooring that is printed or otherwise decorated to achieve a pattern or visual and protected by a clear wear layer.  
1.2 This specification covers heterogeneous polyurethane sheet flooring that shall be composed of binder, fillers, and pigments. The binder shall consist of one or more resins of polyurethane, polyurethane copolymers or other suitable or any desirable combination. Other suitable polymeric resins may be incorporated as part of the binder, provided the polyurethane portion of the binder is greater than 60 % in the base layer.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers the requirements for the compound and physical characteristics of homogeneous (Type I) and layered (Type II) rubber sheet floor covering with backing. Both types shall be fibrous and foamed rubber, and may also contain intermediate layers. They may either have smooth, embossed, or molded pattern surfaces, and shall not contain asbestos. They shall be tested on, and conform accordingly to the following requirements: chemical composition; hardness; modulus of 10 % elongation; static load limit; resistance to chemicals such as white vinegar, rubbing alcohol, sodium hydroxide solution, hydrochloric acid solution, sulfuric acid solution, household ammonia solution, and household bleach; resistance to heat; resistance to light; width and length; and base, wear layer, and overall thicknesses.
SCOPE
1.1 This specification covers the requirements for the compound and physical characteristics of rubber sheet floor covering having a rubber wear layer with backing. Products may also contain intermediate layers.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following precautionary statement pertains only to the test method portion, Section 10, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers the requirements for the compound and physical characteristics of homogeneous (Type I) and layered (Type II) rubber sheet floor covering without backing. The floor coverings may either have smooth, embossed, or molded pattern surfaces, and shall not contain asbestos. They shall be tested on, and conform accordingly to the following requirements: chemical composition; hardness; modulus of 10 % elongation; static load limit; resistance to chemicals such as white vinegar, rubbing alcohol, sodium hydroxide solution, hydrochloric acid solution, sulfuric acid solution, household ammonia solution, and household bleach; resistance to heat; resistance to light; width and length; and base, wear layer, and overall thicknesses.
SCOPE
1.1 This specification covers the requirements for the compound and physical characteristics of rubber sheet floor covering without backing.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following precautionary statement pertains only to the test method portion, Section 10, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers requirements for the compound and physical characteristics of rubber floor tile. The polymeric binder of the rubber floor tile shall have been vulcanized such that it becomes thermoset. The rubber floor tile made from this compound shall be resistant to neutral pH cleaners. For homogeneous rubber floor tile, the surface coloring or mottling shall be uniform throughout the entire thickness of the rubber floor tile. For layered rubber floor tile, the surface color or mottling need not extend through the entire thickness of the rubber floor tile, but must extend throughout the entire thickness of the wear layer. The material shall be tested for heat resistance, abrasion resistance, dimensional stability, and light resistance.
SCOPE
1.1 This specification covers requirements for the compound and physical characteristics of rubber floor tile.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following precautionary statement applies only to the test method portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers resilient floor covering having a vinyl plastic wear layer with backing intended for use in commercial, light commercial, and residential building applications. Material covered by this specification consists of Types I and II floor covering, which may further be classified according to grade (Grades 1, 2, and 3) and backing classes (Class A, B, and C). the floor covering shall consist of a vinyl plastic wear layer (transparent, translucent, or opaque, with the surface smooth, embossed, or textured with or without valley printing), intermediate layers made of foam and reinforcing materials, and backing (which may be fibrous, nonfoamed plastic, or foamed plastic). Tests for wear layer binder content, wear layer thickness, overall thickness, residual indentation, flexibility, and resistance to chemicals, heat, light, and static load shall be performed and shall conform to the requirements specified.
SCOPE
1.1 This specification covers floor covering having a vinyl plastic wear layer with backing. Products may also contain non-PVC specialty performance top layer(s) or intermediate layer(s), or both.  
1.2 Two types of floor covering based on binder content are covered. The floor covering is intended for use in commercial, light commercial, and residential buildings based on serviceability characteristics. General information and performance characteristics that determine serviceability and recommended use are included in this specification.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 The following safety hazards caveat pertains only to the test methods portion, Section 11, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers resilient wall base. These products are manufactured from rubber or thermoplastic materials, or a combination thereof. Wall base is used to provide a functional, as well as decorative border, between walls and floors. This specification does not include rigid products. Wall base shall be of the following types, as specified: type TS - rubber, vulcanized thermoset, type TP - rubber, thermoplastic, and type TV - vinyl, thermoplastic. Wall base shall be one of the following groups, as specified: group 1 - solid, and group 2 - layered. Wall base shall be of the following styles as specified: style A - straight, style B - cove, style C - butt-to, style D - sculptured. The wear layer thickness, flexibility, adjacent surface straining induced by wall base, light resistance, chemical resistance, dimensional stability, height, thickness, and length shall be tested to meet the requirements prescribed.
SCOPE
1.1 This specification covers resilient wall base. These products are manufactured from rubber or thermoplastic materials, or a combination thereof. Wall base is used to provide a functional, as well as decorative border, between walls and floors. This specification does not include rigid products.  
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 The following safety caveat pertains to the test methods portion, Section 12, of this specification:  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification defines the requirements for the compound and physical characteristics of cork floor coverings made from agglomerated composition cork supplied in tile form, to be used with a factory finish or an in situ finish, or both. Cork floor tile covered by this specification shall have a smooth surface and be classified as Class I (Types A and B) and Class II (Types A and B). The standard covers information in the invitation to bid or purchase order, materials and manufacture, physical properties, performance requirements, workmanship, finish and appearance, sampling for testing physical characteristics, inspection, certification, product marking, and packaging and package marking.
SCOPE
1.1 This specification covers requirements for the compound and physical characteristics of cork floor tile. This standard specifies the requirements for cork floor coverings made from agglomerated composition cork supplied in tile form, which are designed to be used with a factory finish or an in situ finish, or both.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers resilient stair treads made of rubber and thermoplastic vinyl for interior use. Treads covered by this specification includes the following types, class, and groups: Type TS, Type TP, Type TV, Class 1, Class 2, Group 1, and Group 2. The material requirements for the tread surface design, nosing style, and color are specified. Some typical nosing styles are illustrated. Treads shall meet the specified performance requirements for: (1) hardness, (2) molded stair tread bonding surface, (3) tread backs, (4) resistance to chemicals for short-term exposure, (5) resistance to heat, and (6) resistance to light. The prescribed dimensional requirements includes tread thickness, length, and depth. The sampling methods for the physical property tests are specified.
SCOPE
1.1 This specification covers resilient treads made of rubber and vinyl for interior use.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification establishes the material, manufacturing, physical, and performance requirements for resilient flooring, typically in tiles or planks format, or both, that are surface decorated or printed and protected by a clear wear layer. The product is a laminated resilient flooring structure that utilizes a polymeric rigid core as part of the product structure and is intended for use in commercial and residential buildings. This type of floor covering may also be manufactured with or without an attached underlay backer for better noise reduction and to help with accommodating minor subfloor irregularities. The wear surface of the resilient tile(s) or plank(s) shall be composed of binder, filler, and pigments compounded with suitable lubricants and processing aids. The binder consists of one or more polymers or copolymers of vinyl chloride, other modifying resins, plasticizers, and stabilizers. The polymers or copolymers of vinyl chloride comprise at least 60% of the weight of the binder. Any copolymer of vinyl chloride used shall contain at least 85% vinyl chloride.
Physical requirements cover binder content, size, thickness, squareness, flatness, openings, and ledging, whereas performance requirements cover residual indentation, surface integrity test, dimensional stability, resistance to chemicals, resistance to heat, resistance to light, and static load resistance. This specification also covers sampling for tests, conditioning, inspection, and certification, as well as workmanship, finish, and appearance, and packaging, packing, and marking.
SCOPE
1.1 This specification covers resilient flooring, typically in tiles or planks format, or both, that are surface decorated or printed and protected by a clear wear layer.  
1.2 This type of floor covering utilizes a polymeric rigid core as part of the product structure.  
1.3 This type of floor covering may utilize an attached underlay backer for reduced noise and for reducing issues concerning minor subfloor irregularities.  
1.4 This type of floor covering is intended for use in commercial and residential buildings. General information and performance characteristics that determine serviceability and recommended use are included in this specification.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification establishes the material and performance characteristics that determine serviceability and recommended applicability of solid vinyl floor tiles intended for use in commercial, light commercial, and residential buildings. Floor tiles shall be classified as Class I for monolithic vinyl tiles, Class II for surface-decorated vinyl tiles, and Class III for printed film vinyl tiles. Furthermore, these classes of tiles shall be subgrouped as Type A for tiles with smooth surfaces, and Type B for those with embossed surfaces. The tiles shall be composed of binder, filler, and pigments compounded with suitable lubricants and processing aids, the composition for all of which shall be dictated by their respective classes. When tested, the tiles shall adhere to the following physical requirements: binder content; dimension including size, thickness, squareness, and dimensional stability; residual indentation; flexibility; resistance to chemicals such as white vinegar, rubbing alcohol, white mineral oil, sodium hydroxide solution, hydrochloric acid solution, sulfuric acid solution, household ammonia solution, household bleach, olive oil, kerozene, unleaded gasoline, and phenol; resistance to heat; and resistance to light.
SCOPE
1.1 This specification covers solid vinyl2 floor tiles that are monolithic, surface decorated or printed, and protected by a clear wear layer.  
1.2 This type of floor covering is intended for use in commercial, light commercial, and residential buildings. General information and performance characteristics which determine serviceability and recommended use are included in this specification.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers sheet floor covering having a vinyl wear layer without backing. Products also may contain a clear specialty performance top layers. This type of floor covering is intended for use in commercial and light commercial buildings. The wear layer shall have a vinyl plastic binder and may include pigments, fillers, extenders, and other ingredients. This layer shall be stabilized against heat and light deterioration. The binder content of the PVC-pattern portion of the wear layer such as vinyl resins, plasticizers, and stabilizers shall be a minimum of 50 %.
SCOPE
1.1 This specification covers sheet floor covering having a vinyl wear layer without backing. Products also may contain a clear specialty performance top layer(s).  
1.2 This type of floor covering is intended for use in commercial and light commercial buildings. General information and performance characteristics, which determine serviceability and recommended use, are included in this specification.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification is intended for polyolefin composition tile with either smooth or embossed surfaces flooring application for use in commercial, light commercial or residential surfaces flooring application. It covers a tile that is composed of binder, fillers and pigments. The binder consists of one or more resins of polyolefin, polyolefin copolymers or polyolefin ter-polymers (or other suitable), or any desirable combination. Other suitable polymeric resins may be incorporated as part of the binder provided the polyolefin portion of the binder system is greater than 50 %. This specification covers materials and manufacture, physical properties, mechanical properties, performance requirements, sampling, and inspection.
SCOPE
1.1 This specification covers polyolefin composition tile with either smooth or embossed surfaces flooring application for use in commercial, light commercial or residential surfaces flooring application.  
1.2 This specification covers a tile that shall be composed of binder, fillers and pigments. The binder shall consist of one or more resins of polyolefin, polyolefin copolymers or polyolefin ter-polymers (or other suitable), or any desirable combination. Other suitable polymeric resins may be incorporated as part of the binder provided the polyolefin portion of the binder system is greater than 50 %.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers sheet linoleum floor covering. These floor coverings are intended for use in commercial, light commercial, and residential buildings based on serviceability characteristics. The floor coverings shall be of the following types: Type I; Type II; and Type III. The jute backing shall be firmly bonded to and partially embedded in the linoleum mix. The minimum amount of linoleum cement shall be 30 % when tested. The following test methods shall be performed: overall thickness; static load; resistance to chemicals; resistance to heat; resistance to light; flexibility; static dissipation; and wear surface.
SCOPE
1.1 This specification covers sheet linoleum floor covering.  
1.2 Three types of linoleum floor covering are covered (see Section 4). These floor coverings are intended for use in commercial, light commercial, and residential buildings based on serviceability characteristics. General information and performance characteristics, which determine serviceability and recommended use, are included in this specification.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 The following safety hazards caveat pertains only to the test methods portion, Section 11, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers polyester composition floor tile for use in commercial, light commercial or residential flooring applications. The tile may be either smooth or embossed. The tile shall be composed of binder, fillers, and pigments, the color and pattern, as applicable shall be as specified in the contract or order. In through pattern tile, either the pattern and colors on the surface of the tile extend entirely through the thickness of the tile without significant change, or the colors appearing on the surface shall extend throughout the entire thickness of the tile, although the appearance of the pattern created by these colors will change throughout the thickness.
SCOPE
1.1 This specification covers polyester composition floor tile for use in commercial, light commercial or residential flooring applications. The tile may be either smooth or embossed.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SCOPE
1.1 This specification covers the requirements for the compound and physical characteristics of heterogeneous polyurethane tile or plank flooring that is printed or otherwise decorated to achieve a pattern or visual and protected by a clear wear layer.  
1.2 This specification covers heterogeneous polyurethane tile or plank flooring that shall be composed of binder, fillers, and pigments. The binder shall consist of one or more resins of polyurethane, polyurethane copolymers or other suitable or any desirable combination. Other suitable polymeric resins may be incorporated as part of the binder, provided the polyurethane portion of the binder is greater than 60 % in the base layer.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SCOPE
1.1 This specification covers the requirements for the compound and physical characteristics of heterogeneous polyurethane tile or plank flooring that is printed or otherwise decorated to achieve a pattern or visual and protected by a clear wear layer.  
1.2 This specification covers heterogeneous polyurethane tile or plank flooring that shall be composed of binder, fillers, and pigments. The binder shall consist of one or more resins of polyurethane, polyurethane copolymers or other suitable or any desirable combination. Other suitable polymeric resins may be incorporated as part of the binder, provided the polyurethane portion of the binder is greater than 60 % in the base layer.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SCOPE
1.1 This specification covers the requirements for the compound and physical characteristics of heterogeneous polyurethane sheet flooring that is printed or otherwise decorated to achieve a pattern or visual and protected by a clear wear layer.  
1.2 This specification covers heterogeneous polyurethane sheet flooring that shall be composed of binder, fillers, and pigments. The binder shall consist of one or more resins of polyurethane, polyurethane copolymers or other suitable or any desirable combination. Other suitable polymeric resins may be incorporated as part of the binder, provided the polyurethane portion of the binder is greater than 60 % in the base layer.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SCOPE
1.1 This specification covers the requirements for the compound and physical characteristics of heterogeneous polyurethane sheet flooring that is printed or otherwise decorated to achieve a pattern or visual and protected by a clear wear layer.  
1.2 This specification covers heterogeneous polyurethane sheet flooring that shall be composed of binder, fillers, and pigments. The binder shall consist of one or more resins of polyurethane, polyurethane copolymers or other suitable or any desirable combination. Other suitable polymeric resins may be incorporated as part of the binder, provided the polyurethane portion of the binder is greater than 60 % in the base layer.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SCOPE
1.1 This specification covers the requirements for the compound and physical characteristics of heterogeneous polyurethane tile or plank flooring that is printed or otherwise decorated to achieve a pattern or visual and protected by a clear wear layer.  
1.2 This specification covers heterogeneous polyurethane tile or plank flooring that shall be composed of binder, fillers, and pigments. The binder shall consist of one or more resins of polyurethane, polyurethane copolymers or other suitable or any desirable combination. Other suitable polymeric resins may be incorporated as part of the binder, provided the polyurethane portion of the binder is greater than 60 % in the base layer.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers the requirements for the compound and physical characteristics of homogeneous (Type I) and layered (Type II) rubber sheet floor covering with backing. Both types shall be fibrous and foamed rubber, and may also contain intermediate layers. They may either have smooth, embossed, or molded pattern surfaces, and shall not contain asbestos. They shall be tested on, and conform accordingly to the following requirements: chemical composition; hardness; modulus of 10 % elongation; static load limit; resistance to chemicals such as white vinegar, rubbing alcohol, sodium hydroxide solution, hydrochloric acid solution, sulfuric acid solution, household ammonia solution, and household bleach; resistance to heat; resistance to light; width and length; and base, wear layer, and overall thicknesses.
SCOPE
1.1 This specification covers the requirements for the compound and physical characteristics of rubber sheet floor covering having a rubber wear layer with backing. Products may also contain intermediate layers.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following precautionary statement pertains only to the test method portion, Section 10, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers the requirements for the compound and physical characteristics of homogeneous (Type I) and layered (Type II) rubber sheet floor covering without backing. The floor coverings may either have smooth, embossed, or molded pattern surfaces, and shall not contain asbestos. They shall be tested on, and conform accordingly to the following requirements: chemical composition; hardness; modulus of 10 % elongation; static load limit; resistance to chemicals such as white vinegar, rubbing alcohol, sodium hydroxide solution, hydrochloric acid solution, sulfuric acid solution, household ammonia solution, and household bleach; resistance to heat; resistance to light; width and length; and base, wear layer, and overall thicknesses.
SCOPE
1.1 This specification covers the requirements for the compound and physical characteristics of rubber sheet floor covering without backing.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following precautionary statement pertains only to the test method portion, Section 10, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers requirements for the compound and physical characteristics of rubber floor tile. The polymeric binder of the rubber floor tile shall have been vulcanized such that it becomes thermoset. The rubber floor tile made from this compound shall be resistant to neutral pH cleaners. For homogeneous rubber floor tile, the surface coloring or mottling shall be uniform throughout the entire thickness of the rubber floor tile. For layered rubber floor tile, the surface color or mottling need not extend through the entire thickness of the rubber floor tile, but must extend throughout the entire thickness of the wear layer. The material shall be tested for heat resistance, abrasion resistance, dimensional stability, and light resistance.
SCOPE
1.1 This specification covers requirements for the compound and physical characteristics of rubber floor tile.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following precautionary statement applies only to the test method portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SCOPE
1.1 This specification covers the requirements for the compound and physical characteristics of bonded rubber crumb floor coverings.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers vinyl composition floor tile with either smooth or embossed surfaces. Vinyl composition tile shall conform to the materials, color, pattern, wearing surface, size, thickness, and squareness indicated in this specification. The material shall be tested for indentation and impact. Performance requirements for vinyl composition tiles include deflection limit, dimensional stability, chemical resistance, and heat resistance. Basic chemicals for chemical resistance test include vinegar, alcohol, mineral oil, sodium hydroxide solution, household ammonia solution, household bleach, olive oil, kerosene, unleaded gasoline, and phenol.
SCOPE
1.1 This specification covers vinyl composition tile (VCT) with either smooth or embossed surfaces for flooring application.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers floor tiles made of a homogeneous mixture of linoleum cement binder calendered or pressed onto a fibrous or suitable backing for use in commercial, light commercial and residential buildings based on serviceability characteristics. General information and performance characteristics, which determine serviceability and recommended use, are included in this document. The floor coverings shall be of the following types: Type I—linoleum floor tile with fibrous backing; Type II—linoleum floor tile with special backing; Type III—linoleum floor tile without backing; and Type IV—static dissipative linoleum floor tile with or without backing. Materials shall be tested and the individual grades shall conform to specified values of physical properties such as wear surface, size, thickness, and squareness; performance requirements such as residual indentation, static load resistance, flexibility, dimensional stability, resistance to chemicals, resistance to heat, resistance to light, and static dissipation.
SCOPE
1.1 This specification covers floor tiles made of a homogeneous mixture of linoleum cement binder calendered or pressed onto a fibrous or suitable backing. This specification also covers linoleum floor tile without backing.  
1.2 Four types of linoleum floor tile are covered. The floor covering is intended for use in commercial, light commercial, and residential buildings based on serviceability characteristics. General information and performance characteristics, which determine serviceability and recommended use, are included in this document.  
1.3 The following safety hazards caveat pertains only to the test methods portion, Sections 7 and 8, of this specification.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification establishes the material and performance characteristics that determine serviceability and recommended applicability of solid vinyl floor tiles intended for use in commercial, light commercial, and residential buildings. Floor tiles shall be classified as Class I for monolithic vinyl tiles, Class II for surface-decorated vinyl tiles, and Class III for printed film vinyl tiles. Furthermore, these classes of tiles shall be subgrouped as Type A for tiles with smooth surfaces, and Type B for those with embossed surfaces. The tiles shall be composed of binder, filler, and pigments compounded with suitable lubricants and processing aids, the composition for all of which shall be dictated by their respective classes. When tested, the tiles shall adhere to the following physical requirements: binder content; dimension including size, thickness, squareness, and dimensional stability; residual indentation; flexibility; resistance to chemicals such as white vinegar, rubbing alcohol, white mineral oil, sodium hydroxide solution, hydrochloric acid solution, sulfuric acid solution, household ammonia solution, household bleach, olive oil, kerozene, unleaded gasoline, and phenol; resistance to heat; and resistance to light.
SCOPE
1.1 This specification covers solid vinyl2 floor tiles that are monolithic, surface decorated or printed, and protected by a clear wear layer.  
1.2 This type of floor covering is intended for use in commercial, light commercial, and residential buildings. General information and performance characteristics which determine serviceability and recommended use are included in this specification.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification establishes the material and performance characteristics that determine serviceability and recommended applicability of solid vinyl floor tiles intended for use in commercial, light commercial, and residential buildings. Floor tiles shall be classified as Class I for monolithic vinyl tiles, Class II for surface-decorated vinyl tiles, and Class III for printed film vinyl tiles. Furthermore, these classes of tiles shall be subgrouped as Type A for tiles with smooth surfaces, and Type B for those with embossed surfaces. The tiles shall be composed of binder, filler, and pigments compounded with suitable lubricants and processing aids, the composition for all of which shall be dictated by their respective classes. When tested, the tiles shall adhere to the following physical requirements: binder content; dimension including size, thickness, squareness, and dimensional stability; residual indentation; flexibility; resistance to chemicals such as white vinegar, rubbing alcohol, white mineral oil, sodium hydroxide solution, hydrochloric acid solution, sulfuric acid solution, household ammonia solution, household bleach, olive oil, kerozene, unleaded gasoline, and phenol; resistance to heat; and resistance to light.
SCOPE
1.1 This specification covers solid vinyl2 floor tiles that are monolithic, surface decorated or printed, and protected by a clear wear layer.  
1.2 This type of floor covering is intended for use in commercial, light commercial, and residential buildings. General information and performance characteristics which determine serviceability and recommended use are included in this specification.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SCOPE
1.1 This specification covers resilient flooring, typically in tiles or planks format, or both, that are surface decorated or printed and protected by a clear wear layer.  
1.2 This type of floor covering utilizes a polymeric rigid core as part of the product structure.  
1.3 This type of floor covering may utilize an attached underlay backer for reduced noise and for reducing issues concerning minor subfloor irregularities.  
1.4 This type of floor covering is intended for use in commercial and residential buildings. General information and performance characteristics that determine serviceability and recommended use are included in this specification.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers polyester composition floor tile for use in commercial, light commercial or residential flooring applications. The tile may be either smooth or embossed. The tile shall be composed of binder, fillers, and pigments, the color and pattern, as applicable shall be as specified in the contract or order. In through pattern tile, either the pattern and colors on the surface of the tile extend entirely through the thickness of the tile without significant change, or the colors appearing on the surface shall extend throughout the entire thickness of the tile, although the appearance of the pattern created by these colors will change throughout the thickness.
SCOPE
1.1 This specification covers polyester composition floor tile for use in commercial, light commercial or residential flooring applications. The tile may be either smooth or embossed.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers resilient wall base. These products are manufactured from rubber or thermoplastic materials, or a combination thereof. Wall base is used to provide a functional, as well as decorative border, between walls and floors. This specification does not include rigid products. Wall base shall be of the following types, as specified: type TS - rubber, vulcanized thermoset, type TP - rubber, thermoplastic, and type TV - vinyl, thermoplastic. Wall base shall be one of the following groups, as specified: group 1 - solid, and group 2 - layered. Wall base shall be of the following styles as specified: style A - straight, style B - cove, style C - butt-to, style D - sculptured. The wear layer thickness, flexibility, adjacent surface straining induced by wall base, light resistance, chemical resistance, dimensional stability, height, thickness, and length shall be tested to meet the requirements prescribed.
SCOPE
1.1 This specification covers resilient wall base. These products are manufactured from rubber or thermoplastic materials, or a combination thereof. Wall base is used to provide a functional, as well as decorative border, between walls and floors. This specification does not include rigid products.  
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 The following safety caveat pertains to the test methods portion, Section 12, of this specification:  This standard does not purport to address all the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers resilient stair treads made of rubber and thermoplastic vinyl for interior use. Treads covered by this specification includes the following types, class, and groups: Type TS, Type TP, Type TV, Class 1, Class 2, Group 1, and Group 2. The material requirements for the tread surface design, nosing style, and color are specified. Some typical nosing styles are illustrated. Treads shall meet the specified performance requirements for: (1) hardness, (2) molded stair tread bonding surface, (3) tread backs, (4) resistance to chemicals for short-term exposure, (5) resistance to heat, and (6) resistance to light. The prescribed dimensional requirements includes tread thickness, length, and depth. The sampling methods for the physical property tests are specified.
SCOPE
1.1 This specification covers resilient treads made of rubber and vinyl for interior use.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

ABSTRACT
This specification covers resilient stair treads made of rubber and thermoplastic vinyl for interior use. Treads covered by this specification includes the following types, class, and groups: Type TS, Type TP, Type TV, Class 1, Class 2, Group 1, and Group 2. The material requirements for the tread surface design, nosing style, and color are specified. Some typical nosing styles are illustrated. Treads shall meet the specified performance requirements for: (1) hardness, (2) molded stair tread bonding surface, (3) tread backs, (4) resistance to chemicals for short-term exposure, (5) resistance to heat, and (6) resistance to light. The prescribed dimensional requirements includes tread thickness, length, and depth. The sampling methods for the physical property tests are specified.
SCOPE
1.1 This specification covers resilient treads made of rubber and vinyl for interior use.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

ABSTRACT
This specification covers requirements for the compound and physical characteristics of rubber floor tile. The polymeric binder of the rubber floor tile shall have been vulcanized such that it becomes thermoset. The rubber floor tile made from this compound shall be resistant to neutral pH cleaners. For homogeneous rubber floor tile, the surface coloring or mottling shall be uniform throughout the entire thickness of the rubber floor tile. For layered rubber floor tile, the surface color or mottling need not extend through the entire thickness of the rubber floor tile, but must extend throughout the entire thickness of the wear layer. The material shall be tested for heat resistance, abrasion resistance, dimensional stability, and light resistance.
SCOPE
1.1 This specification covers requirements for the compound and physical characteristics of rubber floor tile.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers resilient stair treads made of rubber and thermoplastic vinyl for interior use. Treads covered by this specification includes the following types, class, and groups: Type TS, Type TP, Type TV, Class 1, Class 2, Group 1, and Group 2. The material requirements for the tread surface design, nosing style, and color are specified. Some typical nosing styles are illustrated. Treads shall meet the specified performance requirements for: (1) hardness, (2) molded stair tread bonding surface, (3) tread backs, (4) resistance to chemicals for short-term exposure, (5) resistance to heat, and (6) resistance to light. The prescribed dimensional requirements includes tread thickness, length, and depth. The sampling methods for the physical property tests are specified.
SCOPE
1.1 This specification covers resilient treads made of rubber and vinyl for interior use.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

ABSTRACT
This specification covers the requirements for the compound and physical characteristics of homogeneous (Type I) and layered (Type II) rubber sheet floor covering with backing. Both types shall be fibrous and foamed rubber, and may also contain intermediate layers. They may either have smooth, embossed, or molded pattern surfaces, and shall not contain asbestos. They shall be tested on, and conform accordingly to the following requirements: chemical composition; hardness; modulus of 10 % elongation; static load limit; resistance to chemicals such as white vinegar, rubbing alcohol, sodium hydroxide solution, hydrochloric acid solution, sulfuric acid solution, household ammonia solution, and household bleach; resistance to heat; resistance to light; width and length; and base, wear layer, and overall thicknesses.
SCOPE
1.1 This specification covers the requirements for the compound and physical characteristics of rubber sheet floor covering having a rubber wear layer with backing. Products may also contain intermediate layers.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following precautionary statement pertains only to the test method portion, Section 10, of this specification:  This standard does not purport to address all the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers vinyl composition floor tile with either smooth or embossed surfaces. Vinyl composition tile shall conform to the materials, color, pattern, wearing surface, size, thickness, and squareness indicated in this specification. The material shall be tested for indentation and impact. Performance requirements for vinyl composition tiles include deflection limit, dimensional stability, chemical resistance, and heat resistance. Basic chemicals for chemical resistance test include vinegar, alcohol, mineral oil, sodium hydroxide solution, household ammonia solution, household bleach, olive oil, kerosene, unleaded gasoline, and phenol.
SCOPE
1.1 This specification covers vinyl composition tile (VCT) with either smooth or embossed surfaces for flooring application.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers the requirements for the compound and physical characteristics of homogeneous (Type I) and layered (Type II) rubber sheet floor covering without backing. The floor coverings may either have smooth, embossed, or molded pattern surfaces, and shall not contain asbestos. They shall be tested on, and conform accordingly to the following requirements: chemical composition; hardness; modulus of 10 % elongation; static load limit; resistance to chemicals such as white vinegar, rubbing alcohol, sodium hydroxide solution, hydrochloric acid solution, sulfuric acid solution, household ammonia solution, and household bleach; resistance to heat; resistance to light; width and length; and base, wear layer, and overall thicknesses.
SCOPE
1.1 This specification covers the requirements for the compound and physical characteristics of rubber sheet floor covering without backing.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following precautionary statement pertains only to the test method portion, Section 10, of this specification:  This standard does not purport to address all the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers the requirements for the compound and physical characteristics of homogeneous (Type I) and layered (Type II) rubber sheet floor covering with backing. Both types shall be fibrous and foamed rubber, and may also contain intermediate layers. They may either have smooth, embossed, or molded pattern surfaces, and shall not contain asbestos. They shall be tested on, and conform accordingly to the following requirements: chemical composition; hardness; modulus of 10 % elongation; static load limit; resistance to chemicals such as white vinegar, rubbing alcohol, sodium hydroxide solution, hydrochloric acid solution, sulfuric acid solution, household ammonia solution, and household bleach; resistance to heat; resistance to light; width and length; and base, wear layer, and overall thicknesses.
SCOPE
1.1 This specification covers the requirements for the compound and physical characteristics of rubber sheet floor covering having a rubber wear layer with backing. Products may also contain intermediate layers.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following precautionary statement pertains only to the test method portion, Section 10, of this specification:  This standard does not purport to address all the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers sheet floor covering having a vinyl wear layer without backing. Products also may contain a clear specialty performance top layers. This type of floor covering is intended for use in commercial and light commercial buildings. The wear layer shall have a vinyl plastic binder and may include pigments, fillers, extenders, and other ingredients. This layer shall be stabilized against heat and light deterioration. The binder content of the PVC-pattern portion of the wear layer such as vinyl resins, plasticizers, and stabilizers shall be a minimum of 50 %.
SCOPE
1.1 This specification covers sheet floor covering having a vinyl wear layer without backing. Products also may contain a clear specialty performance top layer(s).  
1.2 This type of floor covering is intended for use in commercial and light commercial buildings. General information and performance characteristics, which determine serviceability and recommended use, are included in this specification.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers the requirements for the compound and physical characteristics of homogeneous (Type I) and layered (Type II) rubber sheet floor covering without backing. The floor coverings may either have smooth, embossed, or molded pattern surfaces, and shall not contain asbestos. They shall be tested on, and conform accordingly to the following requirements: chemical composition; hardness; modulus of 10 % elongation; static load limit; resistance to chemicals such as white vinegar, rubbing alcohol, sodium hydroxide solution, hydrochloric acid solution, sulfuric acid solution, household ammonia solution, and household bleach; resistance to heat; resistance to light; width and length; and base, wear layer, and overall thicknesses.
SCOPE
1.1 This specification covers the requirements for the compound and physical characteristics of rubber sheet floor covering without backing.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following precautionary statement pertains only to the test method portion, Section 10, of this specification:  This standard does not purport to address all the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers resilient floor covering having a vinyl plastic wear layer with backing intended for use in commercial, light commercial, and residential building applications. Material covered by this specification consists of Types I and II floor covering, which may further be classified according to grade (Grades 1, 2, and 3) and backing classes (Class A, B, and C). the floor covering shall consist of a vinyl plastic wear layer (transparent, translucent, or opaque, with the surface smooth, embossed, or textured with or without valley printing), intermediate layers made of foam and reinforcing materials, and backing (which may be fibrous, nonfoamed plastic, or foamed plastic). Tests for wear layer binder content, wear layer thickness, overall thickness, residual indentation, flexibility, and resistance to chemicals, heat, light, and static load shall be performed and shall conform to the requirements specified.
SCOPE
1.1 This specification covers floor covering having a vinyl plastic wear layer with backing. Products may also contain non-PVC specialty performance top layer(s) or intermediate layer(s), or both.  
1.2 Two types of floor covering based on binder content are covered. The floor covering is intended for use in commercial, light commercial, and residential buildings based on serviceability characteristics. General information and performance characteristics that determine serviceability and recommended use are included in this specification.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 The following safety hazards caveat pertains only to the test methods portion, Section 11, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This specification covers the requirements for the compound and physical characteristics of bonded rubber crumb floor coverings.  
1.2 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification is intended for polyolefin composition tile with either smooth or embossed surfaces flooring application for use in commercial, light commercial or residential surfaces flooring application. It covers a tile that is composed of binder, fillers and pigments. The binder consists of one or more resins of polyolefin, polyolefin copolymers or polyolefin ter-polymers (or other suitable), or any desirable combination. Other suitable polymeric resins may be incorporated as part of the binder provided the polyolefin portion of the binder system is greater than 50 %. This specification covers materials and manufacture, physical properties, mechanical properties, performance requirements, sampling, and inspection.
SCOPE
1.1 This specification covers polyolefin composition tile with either smooth or embossed surfaces flooring application for use in commercial, light commercial or residential surfaces flooring application.  
1.2 This specification covers a tile that shall be composed of binder, fillers and pigments. The binder shall consist of one or more resins of polyolefin, polyolefin copolymers or polyolefin ter-polymers (or other suitable), or any desirable combination. Other suitable polymeric resins may be incorporated as part of the binder provided the polyolefin portion of the binder system is greater than 50 %.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers floor tiles made of a homogeneous mixture of linoleum cement binder calendered or pressed onto a fibrous or suitable backing for use in commercial, light commercial and residential buildings based on serviceability characteristics. General information and performance characteristics, which determine serviceability and recommended use, are included in this document. The floor coverings shall be of the following types: Type I—linoleum floor tile with fibrous backing; Type II—linoleum floor tile with special backing; Type III—linoleum floor tile without backing; and Type IV—static dissipative linoleum floor tile with or without backing. Materials shall be tested and the individual grades shall conform to specified values of physical properties such as wear surface, size, thickness, and squareness; performance requirements such as residual indentation, static load resistance, flexibility, dimensional stability, resistance to chemicals, resistance to heat, resistance to light, and static dissipation.
SCOPE
1.1 This specification covers floor tiles made of a homogeneous mixture of linoleum cement binder calendered or pressed onto a fibrous or suitable backing. This specification also covers linoleum floor tile without backing.  
1.2 Four types of linoleum floor tile are covered. The floor covering is intended for use in commercial, light commercial, and residential buildings based on serviceability characteristics. General information and performance characteristics, which determine serviceability and recommended use, are included in this document.  
1.3 The following safety hazards caveat pertains only to the test methods portion, Sections 7 and 8, of this specification.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

ABSTRACT
This specification covers sheet linoleum floor covering. These floor coverings are intended for use in commercial, light commercial, and residential buildings based on serviceability characteristics. The floor coverings shall be of the following types: Type I; Type II; and Type III. The jute backing shall be firmly bonded to and partially embedded in the linoleum mix. The minimum amount of linoleum cement shall be 30 % when tested. The following test methods shall be performed: overall thickness; static load; resistance to chemicals; resistance to heat; resistance to light; flexibility; static dissipation; and wear surface.
SCOPE
1.1 This specification covers sheet linoleum floor covering.  
1.2 Three types of linoleum floor covering are covered (see Section 4). These floor coverings are intended for use in commercial, light commercial, and residential buildings based on serviceability characteristics. General information and performance characteristics, which determine serviceability and recommended use, are included in this specification.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 The following safety hazards caveat pertains only to the test methods portion, Section 11, of this specification.  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification defines the requirements for the compound and physical characteristics of cork floor coverings made from agglomerated composition cork supplied in tile form, to be used with a factory finish or an in situ finish, or both. Cork floor tile covered by this specification shall have a smooth surface and be classified as Class I (Types A and B) and Class II (Types A and B). The standard covers information in the invitation to bid or purchase order, materials and manufacture, physical properties, performance requirements, workmanship, finish and appearance, sampling for testing physical characteristics, inspection, certification, product marking, and packaging and package marking.
SCOPE
1.1 This specification covers requirements for the compound and physical characteristics of cork floor tile. This standard specifies the requirements for cork floor coverings made from agglomerated composition cork supplied in tile form, which are designed to be used with a factory finish or an in situ finish, or both.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.