F13.30 - Footwear

SCOPE
1.1 This specification covers minimum slip resistance requirements for the performance of protective (safety) footwear and is intended to help reduce potential injuries. Controlled laboratory tests used to determine compliance with this performance specification shall not be deemed as establishing performance levels for all situations to which individuals may be exposed to.  
1.2 The cited Test Method F2913 allows for testing of alternative flooring or contaminates, or both. It is suggested that testing those alternatives be considered should specific workplace hazards exist.  
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
4.1 Since the heel is an integral support element of the shoe, the heel-attaching strength is a significant factor in ensuring the wearer's safety, as well as the longevity and serviceability of the shoe.  
4.2 This test should be performed on each new style shoe and when any changes are made in the design, material or method of shank or heel area of the shoe, or both, or in the attachment of the heel in an existing shoe.
SCOPE
1.1 This test method covers the determination of the force required to detach the heel from footwear through the application of longitudinal tensile force at a constant displacement rate. The longitudinal test force simulates the most common heel failure mode. Heel height of 20 mm (13/16 in.) or larger is needed to perform this test method properly. Most women's medium and high heeled footwear meets this requirement.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
5.1 This non-proprietary laboratory test method allows for the reproducible testing of whole footwear and footwear-related soling materials for evaluating relative slip performance. Other ASTM test methods generally employ a standardized test foot primarily for evaluation of flooring materials.
SCOPE
1.1 This test method2 determines the dynamic coefficient of friction between footwear and floorings under reproducible laboratory conditions for evaluating relative slip performance. The method is applicable to all types of footwear, outsole units, heel top lifts and sheet soling materials, also to most types of floorings, including matting and stair nosing, and surface contaminants on the flooring surface, including but not limited to liquid water, ice, oil and grease. The method may also be applied to surfaces such as block pavers, turf and gravel.  
1.2 Special purpose footwear or fittings containing spikes, metal studs or similar may be tested on appropriate surfaces but the method does not fully take account of the risk of tripping due to footwear/ground interlock.  
1.3 The values stated in the ASTM test method in metrics are to be regarded as the standard. The values in parentheses are for information.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
4.1 These test methods contain requirements to evaluate the performance of footwear for the following:  
4.1.1 Impact resistance for the toe area of footwear (I),  
4.1.2 Compression resistance for the toe area of footwear (C),  
4.1.3 Metatarsal protection that reduces the chance of injury to the metatarsal bones at the top of the foot (Mt),  
4.1.4 Conductive properties which reduce hazards that may result from static electricity buildup, and reduce the possibility of ignition of explosives and volatile chemicals (Cd),  
4.1.5 Electric hazard to protect the wearer when accidentally stepping on live electric wires (EH),  
4.1.6 Static dissipative properties to reduce hazards that result from a build up of static charge where there is an underlying risk of accidental contact with live electrical circuits (SD), and  
4.1.7 Puncture resistance footwear devices (PR).  
4.2 Any changes to the original components of safety toe footwear such as replacing or adding after-market footbeds/inserts could cause non-compliance to any or all parts of this standard rendering the ASTM label invalid. Protective toe footwear specimens or samples shall be retested for any of the following changes.  
4.2.1 Change in material used to make protective toe cap, change in protective cap manufacturer, change in the design of the toe cap.  
4.2.2 Change in construction method used to make footwear or change in factory in which footwear is produced.  
4.2.3 Change in the upper or insole material thickness greater than 25 %.  
4.2.4 Change in the out sole or midsole, including its hardness.  
4.2.5 Change in shape of last used in the manufacturing of footwear.  
4.2.6 Change in material or supplier of protective insole.  
4.2.7 Change in material or supplier of met guard.
SCOPE
1.1 These test methods measure the resistance of footwear to a variety of hazards that can potentially result in injury.  
1.2 These test methods may be used to test for compliance to minimum performance requirements in established safety standards.  
1.2.1 By agreement between the purchaser and the supplier, or as required by established safety standards, these test methods can be used to determine any one, or all of the following: (1) impact resistance (I), (2) compression resistance (C), (3) metatarsal impact resistance (Mt), (4) resistance to electrical conductivity (Cd), (5) resistance to electric hazard (EH), (6) static dissipative performance (SD), and (7) puncture resistance (PR).  
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification provides certification of protective footwear. It includes performance requirements for footwear to protect workers' feet from a variety of workplace hazards.
SCOPE
1.1 The principal purpose of this specification is the certification of protective footwear. Certification must be performed by independent third party laboratories in order for footwear to bear the ASTM marking.  
1.2 The specification contains performance requirements for footwear to protect workers' feet from the following hazards by providing: (1) conductive properties (Cd) which reduce hazards that may result from static electricity buildup; and reduce the possibility of ignition of explosives and volatile chemicals; (2) electric hazard protection (EH), to protect the wearer from accidental contact by stepping on live electric wires; (3) static dissipative properties (SD) to reduce hazards due to excessively low footwear electrical resistance that may exist where SD footwear is required; (4) puncture resistance (PR) footwear devices.  
1.3 This specification covers minimum requirements for the performance of footwear to provide protection against a variety of workplace hazards other than the toe area that can potentially result in injury.  
1.4 This specification is not intended to serve as a detailed manufacturing or purchasing specification, but can be referenced in purchase contracts to ensure that minimum performance requirements are met.  
1.5 Controlled laboratory tests used to determine compliance with the performance requirements of this specification shall not be deemed as establishing performance levels for all situations to which individuals may be exposed.  
1.6 Any changes to the original components of safety footwear such as replacing or adding after market footbeds/inserts could cause failure to any or all parts of this specification rendering the ASTM Soft Toe Protective Footwear label invalid.  
1.7 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers the minimum design, performance, testing, and classification requirements, and prescribes fit, function, and performance criteria for footwear designed to be worn to provide protection against a variety of workplace hazards that can potentially result in injury. It is not the intention of this specification to serve as a detailed manufacturing or purchasing specification, but can be referenced in purchase contracts to ensure that minimum performance requirements are met. Footwear conforming to this specification shall meet the performance requirements for the following: impact resistance for the toe area of footwear; compression resistance for the toe area of footwear; metatarsal protection that reduces the chance of injury to the metatarsal bones at the top of the foot; conductive properties which reduce hazards that may result from static electricity buildup, and reduce the possibility of ignition of explosives and volatile chemicals; electric shock resistance; static dissipative (SD) properties to reduce hazards due to excessively low footwear resistance that may exist where SD footwear is required; puncture resistance of footwear bottoms; chain saw cut resistance; and dielectric insulation.
SCOPE
1.1 This specification covers minimum requirements for the performance of footwear to provide protection against a variety of workplace hazards that can potentially result in injury.  
1.2 This specification is not intended to serve as a detailed manufacturing or purchasing specification, but can be referenced in purchase contracts to ensure that minimum performance requirements are met.  
1.3 Controlled laboratory tests used to determine compliance with the performance requirements of this specification shall not be deemed as establishing performance levels for all situations to which individuals may be exposed.  
1.4 Any changes to the original components of safety toe footwear such as replacing or adding after market footbeds/inserts could cause failure to any or all parts of this standard rendering the ASTM marking invalid.  
1.5 This specification is not applicable to overshoes with safety toe caps or strap on devices with safety toes.  
1.6 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
4.1 These test methods contain requirements to evaluate the performance of footwear for the following:  
4.1.1 Impact resistance for the toe area of footwear (I/75),  
4.1.2 Compression resistance for the toe area of footwear (C/75),  
4.1.3 Metatarsal protection that reduces the chance of injury to the metatarsal bones at the top of the foot (Mt/75),  
4.1.4 Conductive properties which reduce hazards that may result from static electricity buildup, and reduce the possibility of ignition of explosives and volatile chemicals (Cd),  
4.1.5 Electric Hazard by stepping on live wire (EH),  
4.1.6 Static dissipative (SD) properties to reduce hazards due to excessively low footwear electrical resistance that may exist where SD footwear is required, and  
4.1.7 Puncture resistance footwear devices (PR).  
4.2 Any changes to the original components of safety toe footwear such as replacing or adding after-market footbeds/inserts could cause non-compliance to any or all parts of this standard rendering the ASTM label invalid. Protective toe footwear specimens or samples shall be retested for any of the following changes.  
4.2.1 Change in material used to make protective toe cap, change in protective cap manufacturer, change in the design of the toe cap.  
4.2.2 Change in construction method used to make footwear or change in factory in which footwear is produced.  
4.2.3 Change in the upper or insole material thickness greater than 25 %, change to the soling system or a change in the hardness of the outsole.  
4.2.4 Change in shape of last used in the manufacturing of footwear.  
4.2.5 Change in material or supplier of protective insole.  
4.2.6 Change in material or supplier of met guard.
SCOPE
1.1 These test methods measure the resistance of footwear to a variety of hazards that can potentially result in injury.  
1.2 These test methods may be used to test for compliance to minimum performance requirements in established safety standards.  
1.2.1 By agreement between the purchaser and the supplier, or as required by established safety standards, these test methods can be used to determine any one, or all of the following: (1) impact resistance (I), (2) compression resistance (C), (3) metatarsal impact resistance (Mt), (4) resistance to electrical conductivity (Cd), (5) resistance to electric hazard (EH), (6) static dissipative performance (SD), and (7) puncture resistance (PR).  
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification covers the minimum design, performance, testing, and classification requirements, and prescribes fit, function, and performance criteria for footwear designed to be worn to provide protection against a variety of workplace hazards that can potentially result in injury. It is not the intention of this specification to serve as a detailed manufacturing or purchasing specification, but can be referenced in purchase contracts to ensure that minimum performance requirements are met. Footwear conforming to this specification shall meet the performance requirements for the following: impact resistance for the toe area of footwear; compression resistance for the toe area of footwear; metatarsal protection that reduces the chance of injury to the metatarsal bones at the top of the foot; conductive properties which reduce hazards that may result from static electricity buildup, and reduce the possibility of ignition of explosives and volatile chemicals; electric shock resistance; static dissipative (SD) properties to reduce hazards due to excessively low footwear resistance that may exist where SD footwear is required; puncture resistance of footwear bottoms; chain saw cut resistance; and dielectric insulation.
SCOPE
1.1 This specification covers minimum requirements for the performance of footwear to provide protection against a variety of workplace hazards that can potentially result in injury.  
1.2 This specification is not intended to serve as a detailed manufacturing or purchasing specification, but can be referenced in purchase contracts to ensure that minimum performance requirements are met.  
1.3 Controlled laboratory tests used to determine compliance with the performance requirements of this specification shall not be deemed as establishing performance levels for all situations to which individuals may be exposed.  
1.4 Any changes to the original components of safety toe footwear such as replacing or adding after market footbeds/inserts could cause failure to any or all parts of this standard rendering the ASTM marking invalid.  
1.5 This specification is not applicable to overshoes with safety toe caps or strap on devices with safety toes.  
1.6 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This specification provides certification of protective footwear. It includes performance requirements for footwear to protect workers' feet from a variety of workplace hazards.
SCOPE
1.1 The principal purpose of this specification is the certification of protective footwear. Certification must be performed by independent third party laboratories in order for footwear to bear the ASTM marking.  
1.2 The specification contains performance requirements for footwear to protect workers' feet from the following hazards by providing: (1) conductive properties (Cd) which reduce hazards that may result from static electricity buildup; and reduce the possibility of ignition of explosives and volatile chemicals; (2) electric hazard protection (EH), to protect the wearer from accidental contact by stepping on live electric wires; (3) static dissipative properties (SD) to reduce hazards due to excessively low footwear electrical resistance that may exist where SD footwear is required; (4) puncture resistance (PR) footwear devices.  
1.3 This specification covers minimum requirements for the performance of footwear to provide protection against a variety of workplace hazards other than the toe area that can potentially result in injury.  
1.4 This specification is not intended to serve as a detailed manufacturing or purchasing specification, but can be referenced in purchase contracts to ensure that minimum performance requirements are met.  
1.5 Controlled laboratory tests used to determine compliance with the performance requirements of this specification shall not be deemed as establishing performance levels for all situations to which individuals may be exposed.  
1.6 Any changes to the original components of safety footwear such as replacing or adding after market footbeds/inserts could cause failure to any or all parts of this specification rendering the ASTM Soft Toe Protective Footwear label invalid.  
1.7 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
5.1 This non-proprietary laboratory test method allows for the reproducible testing of whole footwear and footwear-related soling materials for evaluating relative slip performance. Other ASTM test methods generally employ a standardized test foot primarily for evaluation of flooring materials.
SCOPE
1.1 This test method2 determines the dynamic coefficient of friction between footwear and floorings under reproducible laboratory conditions for evaluating relative slip performance. The method is applicable to all types of footwear, outsole units, heel top lifts and sheet soling materials, also to most types of floorings, including matting and stair nosing, and surface contaminants on the flooring surface, including but not limited to liquid water, ice, oil and grease. The method may also be applied to surfaces such as block pavers, turf and gravel.  
1.2 Special purpose footwear or fittings containing spikes, metal studs or similar may be tested on appropriate surfaces but the method does not fully take account of the risk of tripping due to footwear/ground interlock.  
1.3 The values stated in the ASTM test method in metrics are to be regarded as the standard. The values in parentheses are for information.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
4.1 Since the heel is an integral support element of the shoe, the heel-attaching strength is a significant factor in ensuring the wearer's safety, as well as the longevity and serviceability of the shoe.  
4.2 This test should be performed on each new style shoe and when any changes are made in the design, material or method of shank or heel area of the shoe, or both, or in the attachment of the heel in an existing shoe.
SCOPE
1.1 This test method covers the determination of the force required to detach the heel from footwear through the application of longitudinal tensile force at a constant displacement rate. The longitudinal test force simulates the most common heel failure mode. Heel height of 20 mm (13/16 in.) or larger is needed to perform this test method properly. Most women's medium and high heeled footwear meets this requirement.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SIGNIFICANCE AND USE
This non-proprietary laboratory test method allows preliminarily for the reproducible testing of whole footwear and footwear-related soling materials for evaluating relative slip performance. Other ASTM test methods generally employ a standardized test foot primarily for evaluation of flooring materials.
FIG. 1 Example of Footwear Mounted Using 7° Wedge to Set Proper Contact Angle
SCOPE
1.1 This test method determines the dynamic coefficient of friction between footwear and floorings under reproducible laboratory conditions for evaluating relative slip performance. The method is applicable to all types of footwear, outsole units, heel top-pieces (top-lifts) and sheet soling materials, also to most types of indoor floorings, including matting and stair nosing, and surface contaminants on the flooring surface, including but not limited to liquid water, ice, oil and grease. The method may also be applied to surfaces such as block pavers, turf and gravel.
1.2 Special purpose footwear or fittings containing spikes, metal studs or similar may be tested on appropriate surfaces but the method does not fully take account of the risk of tripping due to footwear/ground interlock.
1.3 The values stated in the ASTM test method in metrics are to be regarded as the standard. The values in parentheses are for information.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers the minimum design, performance, testing, and classification requirements, and prescribes fit, function, and performance criteria for footwear designed to be worn to provide protection against a variety of workplace hazards that can potentially result in injury. It is not the intention of this specification to serve as a detailed manufacturing or purchasing specification, but can be referenced in purchase contracts to ensure that minimum performance requirements are met. Footwear conforming to this specification shall meet the performance requirements for the following: impact resistance for the toe area of footwear; compression resistance for the toe area of footwear; metatarsal protection that reduces the chance of injury to the metatarsal bones at the top of the foot; conductive properties which reduce hazards that may result from static electricity buildup, and reduce the possibility of ignition of explosives and volatile chemicals; electric shock resistance; static dissipative (SD) properties to reduce hazards due to excessively low footwear resistance that may exist where SD footwear is required; puncture resistance of footwear bottoms; chain saw cut resistance; and dielectric insulation.
SCOPE
1.1 This specification covers minimum requirements for the performance of footwear to provide protection against a variety of workplace hazards that can potentially result in injury.
1.2 This specification is not intended to serve as a detailed manufacturing or purchasing specification, but can be referenced in purchase contracts to ensure that minimum performance requirements are met.
1.3 Controlled laboratory tests used to determine compliance with the performance requirements of this specification shall not be deemed as establishing performance levels for all situations to which individuals may be exposed.
1.4 Any changes to the original components of safety toe footwear such as replacing or adding after market footbeds/inserts could cause failure to any or all parts of this standard rendering the ASTM marking invalid.
1.5 This specification is not applicable to overshoes with safety toe caps or strap on devices with safety toes.
1.6 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification provides certification of protective footwear. It includes performance requirements for footwear to protect workers' feet from a variety of workplace hazards.
SCOPE
1.1 The principle purpose of this specification is the certification of protective footwear. Certification must be performed by independent third party laboratories in order for footwear to bare the ASTM marking.
1.2 The specification contains performance requirements for footwear to protect workers' feet from the following hazards by providing: (1) conductive properties (Cd) which reduce hazards that may result from static electricity buildup; and reduce the possibility of ignition of explosives and volatile chemicals; (2) electric hazard protection (EH), to protect the wearer when accidental contact by stepping on live electric wires; (3) static dissipative properties (SD) to reduce hazards due to excessively low footwear electrical resistance that may exist where SD footwear is required; (4) puncture resistance (PR) footwear devices.
1.3 This specification covers minimum requirements for the performance of footwear to provide protection against a variety of workplace hazards other than the toe area that can potentially result in injury.
1.4 This specification is not intended to serve as a detailed manufacturing or purchasing specification, but can be referenced in purchase contracts to ensure that minimum performance requirements are met.
1.5 Controlled laboratory tests used to determine compliance with the performance requirements of this specification shall not be deemed as establishing performance levels for all situations to which individuals may be exposed.
1.6 Any changes to the original components of safety footwear such as replacing or adding after market footbeds/inserts could cause failure to any or all parts, or a combination thereof, of this specification rendering the ASTM Soft Toe Protective Footwear label invalid.
1.7 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SIGNIFICANCE AND USE
These test methods contain requirements to evaluate the performance of footwear for the following:
Impact resistance for the toe area of footwear (I/75),
Compression resistance for the toe area of footwear (C/75),
Metatarsal protection that reduces the chance of injury to the metatarsal bones at the top of the foot (Mt/75),
Conductive properties which reduce hazards that may result from static electricity buildup, and reduce the possibility of ignition of explosives and volatile chemicals (Cd),
Electric Hazard by stepping on live wire (EH),
Static dissipative (SD) properties to reduce hazards due to excessively low footwear electrical resistance that may exist where SD footwear is required, and
Puncture resistance footwear devices (PR).
Any changes to the original components of safety toe footwear such as replacing or adding after market footbeds/inserts could cause non compliance to any or all parts of this standard rendering the ASTM label invalid. Protective toe footwear specimens or samples shall be retested for any of the following changes.
Change in material used to make protective toe cap, change in protective cap manufacturer, change in the design of the toe cap.
Change in construction method used to make footwear or change in factory in which footwear is produced.
Change in the upper or insole material thickness greater than 25 %, change to the soling system or a change in the hardness of the outsole.
Change in shape of last used in the manufacturing of footwear.
Change in material or supplier of protective insole.
Change in material or supplier of met guard.
SCOPE
1.1 These test methods measure the resistance of footwear to a variety of hazards that can potentially result in injury.
1.2 These test methods may be used to test for compliance to minimum performance requirements in established safety standards.
1.2.1 By agreement between the purchaser and the supplier, or as required by established safety standards, these test methods can be used to determine any one, or all of the following: (1) impact resistance (I), (2) compression resistance (C), (3) metatarsal impact resistance (Mt), (4) resistance to electrical conductivity (Cd), (5) resistance to electric hazard (EH), (6) static dissipative performance (SD), and (7) puncture resistance (PR).
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SIGNIFICANCE AND USE
Since the heel is an integral support element of the shoe, the heel-attaching strength is a significant factor in ensuring the wearer's safety, as well as the longevity and serviceability of the shoe.
This test should be performed on each new style shoe and when any changes are made in the design, material or method of shank or heel area of the shoe, or both, or in the attachment of the heel in an existing shoe.
SCOPE
1.1 This test method covers the determination of the force required to detach the heel from footwear through the application of longitudinal tensile force at a constant displacement rate. The longitudinal test force simulates the most common heel failure mode. Heel height of 20 mm (13/16 in.) or larger is needed to perform this test method properly. Most women's medium and high heeled footwear meets this requirement.
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers the minimum design, performance, testing, and classification requirements, and prescribes fit, function, and performance criteria for footwear designed to be worn to provide protection against a variety of workplace hazards that can potentially result in injury. It is not the intention of this specification to serve as a detailed manufacturing or purchasing specification, but can be referenced in purchase contracts to ensure that minimum performance requirements are met. Footwear conforming to this specification shall meet the performance requirements for the following: impact resistance for the toe area of footwear; compression resistance for the toe area of footwear; metatarsal protection that reduces the chance of injury to the metatarsal bones at the top of the foot; conductive properties which reduce hazards that may result from static electricity buildup, and reduce the possibility of ignition of explosives and volatile chemicals; electric shock resistance; static dissipative (SD) properties to reduce hazards due to excessively low footwear resistance that may exist where SD footwear is required; puncture resistance of footwear bottoms; chain saw cut resistance; and dielectric insulation.
SCOPE
1.1 This specification covers minimum requirements for the design, performance, testing, and classification of footwear designed to provide protection against a variety of workplace hazards that can potentially result in injury.
1.2 The objective of this specification is to prescribe fit, function, and performance criteria for footwear that is intended to be worn to reduce injuries.
1.3 This specification is not intended to serve as a detailed manufacturing or purchasing specification, but can be referenced in purchase contracts to ensure that minimum performance requirements are met.
1.4 Controlled laboratory tests used to determine compliance with the performance requirements of this specification shall not be deemed as establishing performance levels for all situations to which individuals may be exposed.
1.5 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SIGNIFICANCE AND USE
The purpose of these test methods is to provide measurable criteria for various hazards.
The protection that can be demonstrated by evaluation of footwear includes the following:
4.2.1 The effectiveness of impact resistant footwear to eliminate or diminish the severity of injury to the toe area of the foot when subjected to a falling object.
4.2.2 The effectiveness of compression resistant footwear to eliminate or diminish the severity of injury to the toe area of the foot when subjected to a compressive force.
4.2.3 The effectiveness of metatarsal protective footwear to eliminate or diminish the severity of injury to the metatarsal area adjacent to where the toes and the bones of the upper foot intersect.
4.2.4 The effectiveness of conductive footwear to safely reduce the buildup of static electricity from wearer to ground so as to reduce the possibility of ignition of explosives and volatile chemicals.
4.2.5 The effectiveness of electric shock resistant footwear to provide resistance to electric shock when accidental contact is made with live wires.
4.2.6 The effectiveness of static dissipative footwear to reduce the hazards due to excessively low footwear electrical resistance that may exist where SD footwear is required.
4.2.7 The effectiveness of puncture resistant footwear to reduce the possibility of puncture injury to the bottom of the human foot.
4.2.8 The effectiveness of chain saw cut resistant footwear to reduce the chance of injury when exposed to a running power chain saw.
4.2.9 The effectiveness of dielectric insulative footwear to reduce the possibility of injury when exposed to a high voltage charge.
SCOPE
1.1 These test methods measure the resistance of footwear to a variety of hazards that can potentially result in injury.
1.2 These test methods may be used to test for compliance to minimum performance requirements in established safety standards.
1.2.1 By agreement between the purchaser and the supplier, or as required by established safety standards, these test methods can be used to determine any one, or all of the following: (1) impact resistance, (2) compression resistance, (3) metatarsal impact resistance, (4) resistance to electrical conductivity, (5) resistance to electric shock, (6) static dissipative performance, (7) puncture resistance of outsoles,  (8) chain saw cut resistance, and (9) dielectric insulation.
1.3 &si-value;
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SIGNIFICANCE AND USE
Since the heel is an integral support element of the shoe, the heel-attaching strength is a significant factor in ensuring the wearer’safety, as well as the longevity and serviceability of the shoe.
This test should be performed on each new style shoe and when any changes are made in the design, material or method of shank or heel area of the shoe, or both, or in the attachment of the heel in an existing shoe.
SCOPE
1.1 This method covers the determination of the force required to detach the heel from footwear through the application of longitudinal tensile force at a constant displacement rate. The longitudinal test force simulates the most common heel failure mode. Heel height of 20 mm (13/16 in.) or larger is needed to perform this test method properly. Most women's medium and high heeled footwear meets this requirement.
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This test method covers the determination of heel attachment strength on women's and misses' shoes through application of a static load to the heel. Shoe heels may be made of various materials, including wood, plastic, leather, or rubber. The heels may be attached to the shoe body with nails, screws, staples, cement, or a combination of these.
1.2 This test method is applicable for testing heel heights 11/2 in. (38 mm) and higher. (Heel heights are manufactured in 1/8-in. increments.) This testing is applicable for front or back of heel.