25.140.01 - Hand-held tools in general

TAN - // IEC Corrigendum

This document specifies a laboratory method for measuring hand-transmitted vibration emission at the handles of hand-held power-driven angle and vertical grinders. It is a type-test procedure for establishing the magnitude of vibration in the gripping areas of a machine fitted with a specified test wheel and run under no‑load conditions. The method has been established for surface grinding tasks only. Cutting and sanding generally create lower vibrations. It is intended that the results be used ...view more

This document specifies minimum values for Rockwell hardness and torsional strength for hand-operated wrenches and sockets. It covers the following three series of torsion torques: — Series A: usual box wrenches and socket wrenches; EXAMPLE 1 Reference nos. 1 1 02 01 0; 1 1 02 02 0 and 1 1 02 02 1; 1 1 02 03 0; 1 1 02 04 0; 1 1 02 05 0; 1 1 02 06 0; 1 1 02 09 0; 1 1 02 10 0; 1 1 02 11 0; 1 1 02 12 0; 1 1 02 13 0 and 1 1 02 13 1; 1 1 02 14 0; 1 1 02 15 0; 1 1 08 01 0; 1 1 08 02 0. — Series C: ope...view more

This document specifies hardness and minimum torsional strength for machine-operated square drive sockets in accordance with ISO 2725-2 intended for use with impact wrenches. EXAMPLE Reference nos. 2 2 02 01 0; 2 2 02 02 0; 5 2 00 04 0. NOTE The sockets mentioned above are listed under their respective reference numbers in ISO 1703.

Based on IEC corrigendum

This document specifies the design, construction, guidance on use and maintenance of a dynamic loading device for the following categories of hand-held power tools: — percussive; — rotary-percussive. The device can be used when measurements are being made for vibration and noise including when required for specification in test standards.

This document is applicable to insulated, insulating and hybrid hand tools used for working
live or close to live parts at nominal voltages up to 1 000 V AC and 1 500 V DC.
The products designed and manufactured according to this document contribute to the safety
of the users provided they are used by skilled persons, in accordance with safe methods of
work and the instructions for use (where appropriate).

ISO 1703:2018 gives a nomenclature in English of assembly tools for screws and nuts. NOTE Annex A provides the technically equivalent terms in French, one of the other official ISO languages. In addition, this document gives the equivalent terms in German, Italian, Spanish and Swedish (see Annex B). These terms are published under the responsibility of the member bodies for Germany (DIN), Italy (UNI), Spain (UNE) and Sweden (SIS) and are given for information only. However, only the English and ...view more

ISO 2725-2:2017 specifies dimensions, designation, and marking of machine-operated "impact" square drive sockets with operating end having a hexagonal or double hexagonal form in accordance with ISO 1174‑2. NOTE Machine-operated "impact" square drive sockets covered by this document are the ones identified in ISO 1703 under reference numbers 2 2 02 01 0. ISO 2725-2:2017 does not cover technical specifications for these products. Technical specifications are given in ISO 1711‑2.

ISO 2725-3:2017 specifies dimensions, designation, and marking of machine-operated "non-impact" square drive sockets. NOTE Machine-operated "non-impact" square drive sockets covered by this document are the ones identified in ISO 1703 under reference numbers 2 2 02 01 0.

2013-09-20 EMA: Draft for //ENQ received in ISO/CS (see notification of 2013-09-19 in dataservice).

2013-09-20 EMA: Draft for //ENQ received in ISO/CS (see notification of 2013-09-19 in dataservice).

2013-10-02 EMA: Draft for //ENQ received in ISO/CS (see notification of 2013-10-02 in dataservice).

2013-10-02 EMA: Draft for //ENQ received in ISO/CS (see notification of 2013-10-02 in dataservice).

ISO 2351-3:2014 prescribes the technical specifications for machine-operated screwdriver bits for hexagon socket screws, listed in ISO 1703 under reference number 3 2 03 01 0. It applies to bits with male hexagon drive or with cylindrical flat-end drive as defined in ISO 1173 and to tips for screwdrivers as defined in ISO 2936. It also gives recommended combinations between tips and bits.

IEC 60745-2-23:2012 applies to die grinders and small rotary tools for mounted accessories not exceeding 55 mm in diameter and mounted sanding accessories not exceeding 80 mm in diameter such as, threaded cones or plugs that are threaded on a mandrel with an unrelieved shoulder flange, mandrel mounted wheels and rotary files with a rated speed not exceeding a peripheral speed of the accessory of 80 m/s at rated capacity. This part 2 is to be used in conjunction with the latest edition of IEC 607...view more

This document provides the basis for the drafting of vibration test codes for hand-held and hand-guided powerdriven machinery. It specifies the determination of hand-transmitted vibration emission in terms of frequencyweighted root-mean-square (r.m.s.) acceleration during type testing. For machines where vibration test codes do not exist, it may also be used for determination of emission values and contains sufficient guidance for designing an appropriate test. NOTE Vibration test codes based on...view more

ISO 28927-12:2012 specifies a laboratory method for measuring hand-transmitted vibration emission at the handles of hand-held power driven portable die grinders. It is a type-test procedure for establishing the magnitude of vibration in the gripping areas of the machines where operating under type test conditions. It is intended that the results be used to compare different models of the same type of machine.
ISO 28927-12:2012 is applicable to hand-held machines, driven pneumatically or by othe...view more