ASTM E2517-11

Standard Specification for Cargo Bed Cover, Type III (M35A2, 2 1/2 Ton Cargo Truck/M1078, 2 1/2 Ton Lightweight Medium Tactical Vehicle (LMTV)/ M1082, 2 1/2 Ton LMTV Trailer)

ABSTRACT
This specification covers the general requirements for the Type III cargo bed cover (CBC). The Type III cargo bed cover is a removable general purpose rigid enclosure for the cargo bed of the 2-1/2 ton cargo truck (M35A2), 2-1/2 ton lightweight medium tactical vehicle (LMTV; M1078), and 2-1/2 ton LMTV trailer (M1082). The CBC provides environmental protection and security for mission equipment and items of general transport.
SCOPE
1.1 This specification covers the general requirements for the Type III Cargo Bed Cover (CBC). The Type III CBC is a removable general purpose rigid wall enclosure that is mounted on any of the following model 2.5 ton cargo trucks (1) the M35A2 Lightweight Medium Tactical Vehicle (LMTV) and (2) the M1078 LMTV . It can also be mounted on the M1082 LMTV Trailer. The CBC provides environmental protection and security for mission equipment and items of general transport.
1.2 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.
1.3 The following safety hazards caveat pertains only to the test required portion, Section 4, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

General Information

• Status: Historical
• Publication Date: 31-Aug-2011
• ICS: 43.080.10 - Trucks and trailers
• Technical Committee: E06 - Performance of Buildings
• Drafting Committee: E06.53 - Materials and Processes for Durable Rigidwall Relocatable Structures

Relations

• Replaces: ASTM E2517-06 - Standard Specification for Cargo Bed Cover, Type III (M35A2, 2 <bold> 1</bold>/<bold>2</bold> Ton Cargo Truck/M1078, 2 <bold>1</bold>/<bold> 2</bold> Ton Lightweight Medium Tactical Vehicle (LMTV)/M1082, 2 <bold>1</bold>/<bold> 2</bold> Ton LMTV Trailer)
• Effective Date: 01-Sep-2011

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:E2517 −11
StandardSpecification for
Cargo Bed Cover, Type III (M35A2, 2 1/2 Ton Cargo Truck/
M1078, 2 1/2 Ton Lightweight Medium Tactical Vehicle
1
(LMTV)/ M1082, 2 1/2 Ton LMTV Trailer)
This standard is issued under the fixed designation E2517; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
4
1. Scope 2.2 Federal Standards:
FED-STD-595Colors Used in Government Procurement
1.1 This specification covers the general requirements for
4
2.3 Military Standards:
the Type III Cargo Bed Cover (CBC). The Type III CBC is a
MIL-C-46168Coating, Aliphatic Polyurethane, Chemical
removablegeneralpurposerigidwallenclosurethatismounted
Agent Resistant
on any of the following model 2.5ton cargo trucks (1) the
MIL-CDTL-53039Coating, Aliphatic Polyurethane, Single
M35A2LightweightMediumTacticalVehicle(LMTV)and(2)
Component, Chemical Agent Resistant
the M1078 LMTV . It can also be mounted on the M1082
MIL-CDTL-53072 Chemical Agent Resistant Coating
LMTV Trailer. The CBC provides environmental protection
(CARC)SystemApplicationProceduresandQualityCon-
and security for mission equipment and items of general
trol Inspection
transport.
MIL-PRF-22750Coating, Epoxy, High Solids
1.2 The values stated in inch-pound units are to be regarded
MIL-STD-209Slinging and Tiedown Provisions for Lifting
asstandard.Nootherunitsofmeasurementareincludedinthis
and Tying Down Military Equipment
standard.
MIL-STD-810 Environmental Test Methods and Engineer-
1.3 The following safety hazards caveat pertains only to the
ing Guidelines
test required portion, Section 4, of this specification: This
MIL-STD-1366Transportability Criteria
standard does not purport to address all of the safety concerns,
MIL-STD-1472Design Criteria: Human Engineering
if any, associated with its use. It is the responsibility of the user 4
2.4 Military Handbooks:
of this standard to establish appropriate safety and health
MIL-HDBK-759Human Engineering Design
practicesanddeterminetheapplicabilityofregulatoryrequire-
MIL-HDBK-1791Designing for Internal Aerial Delivery in
ments prior to use.
Fixed Winged Aircraft
5
2.5 OSHA Documents:
2. Referenced Documents
Title 29 CFR 1910OHSA Permissible Exposure Limits
2
6
2.1 ASTM Standards:
2.6 ACGIH Documents:
E1925Specification for Engineering and Design Criteria for
ACGIHThreshold Limit Values
Rigid Wall Relocatable Structures
F501Test Method for Aerospace Materials Response to
3. General Requirements
Flame, with Vertical Test Specimen (for Aerospace Ve-
3.1 First Article—When specified (see 6.2), a sample shall
3
hicles Standard Conditions) (Withdrawn 1998)
besubjectedtofirstarticleinspectioninaccordancewith4.1.1.
A first article is defined as a pre-production or an initial
production sample consisting of one or more of each type of
1
This specification is under the jurisdiction of ASTM Committee E06 on
completed CBC.
Performance of Buildings and is the direct responsibility of Subcommittee E06.53
on Materials and Processes for Durable Rigidwall Relocatable Structures.
Current edition approved Sept. 1, 2011. Published October 2011. Originally
4
approved in 2006. Last previous edition approved in 2006 as E2517–06. DOI: Available from Standardization Documents Order Desk, DODSSP, Bldg. 4,
10.1520/E2517-11. Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http://
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or www.dodssp.daps.mil.
5
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Available from Occupational Safety and Health Administration (OSHA), 200
Standards volume information, refer to the standard’s Document Summary page on Constitution Ave., NW, Washington, DC 20210, http://www.osha.gov.
6
the ASTM website. Available from American Conference of Governmental Industrial Hygienists,
3
The last approved version of this historical standard is referenced on Inc. (ACGIH), 1330 Kemper Meadow Dr., Suite 600, Cincinnati, OH 45240,
www.astm.org. http://www.acgih.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
E2517−11
3.2 Conformance—Items furnished under this specification 3.3.5.2 Gases or Vapors—The materials, as installed in the
shall be subjected to conformance inspection in accordance equipment and under service conditions specified in the equip-
with 4.1.2. ment specification, shall not liberate noxious odors, toxic or
corrosive gases, or vapors that would be detrimental to the
3.3 Operating Requirements—Unless otherwise specified,
health of pe
...

This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:E2517–06 Designation: E2517 – 11
Standard Specification for
Cargo Bed Cover, Type III (M35A2, 2 1/2 Ton Cargo Truck/
M1078, 2 1/2 Ton Lightweight Medium Tactical Vehicle
1
(LMTV)/ M1082, 2 1/2 Ton LMTV Trailer)
This standard is issued under the fixed designation E2517; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1This specification covers the general requirements for the Type III Cargo Bed Cover (CBC). The Type III Cargo Bed Cover
1 1
isaremovablegeneralpurposerigidenclosureforthecargobedoftheM35A2,2 ⁄2TonCargoTruck/M1078,2 ⁄2TonLightweight
1
Medium Tactical Vehicle (LMTV)/M1082, 2 ⁄2 Ton LMTVTrailer. The CBC provides environmental protection and security for
mission equipment and items of general transport.
1.1 This specification covers the general requirements for the Type III Cargo Bed Cover (CBC). The Type III CBC is a
removablegeneralpurposerigidwallenclosurethatismountedonanyofthefollowingmodel2.5toncargotrucks(1)theM35A2
Lightweight Medium Tactical Vehicle (LMTV) and (2) the M1078 LMTV . It can also be mounted on the M1082 LMTVTrailer.
The CBC provides environmental protection and security for mission equipment and items of general transport.
1.2 Thevaluesstatedininch-poundunitsaretoberegardedasthestandard.Thevaluesgiveninparenthesisareforinformation
only. The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this
standard.
1.3 The following safety hazards caveat pertains only to the test required portion, Section 4, of this specification: This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to
use.
2. Referenced Documents
2
2.1 ASTM Standards:
E1925 Specification for Engineering and Design Criteria for Rigid Wall Relocatable Structures
3
F501 Test Method for Aerospace Materials Response to Flame, With Vertical Test Specimen
4
2.2 Federal Standard: Federal Standards:
FED-STD-595 Colors Used in Government Procurement
4
2.3 Military Standards: Military Standards:
MIL-C-46168 Coating, Aliphatic Polyurethane, Chemical Agent Resistant
MIL-CDTL-53039 Coating, Aliphatic Polyurethane, Single Component, Chemical Agent Resistant
MIL-CDTL-53072 ChemicalAgent Resistant Coating (CARC) SystemApplication Procedures and Quality Control Inspection
MIL-PRF-22750 Coating, Epoxy, High Solids
MIL-STD-209 Slinging and Tiedown Provisions for Lifting and Tying Down Military Equipment
MIL-STD-810 Environmental Test Methods and Engineering Guidelines
MIL-STD-1366 Transportability Criteria MIL-PRF-22750Coating, Epoxy, High Solids
MIL-CDTL-53039 Coating, Aliphatic Polyurethane, Single Component, Chemical Agent Resistant
MIL-CDTL-53072Chemical Agent Resistant Coating (CARC) System Application Procedures and Quality Control Inspection
2.4 Military Handbook:
MIL-STD-1472 Design Criteria: Human Engineering
1
This specification is under the jurisdiction ofASTM Committee E06 on Performance of Buildings and is the direct responsibility of Subcommittee E06.53 on Materials
and Processes for Durable Rigidwall Relocatable Structures.
Current edition approved Oct. 1, 2006. Published October 2006. DOI: 10.1520/E2517-06.
Current edition approved Sept. 1, 2011. Published October 2011. Originally approved in 2006. Last previous edition approved in 2006 as E2517–06. DOI:
10.1520/E2517-11.
2
ForreferencedASTMstandards,visittheASTMwebsite,www.astm.org,[e-mail] Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Withdrawn. The last approved version of this historical standard is referenced on www.astm.org.
4
Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http://www.dodssp.daps.mil.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
E2517 – 11
4
2.4 Military Handbooks:
MIL-HDBK-759 Human Engineering Design
MIL-HDBK-1791 Designing for Internal Aerial Delivery in
...