iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D3006-99(2004)

(Specification)

Standard Specification for Polyethylene Plastic Pressure-Sensitive Electrical Insulating Tape

Standard Specification for Polyethylene Plastic Pressure-Sensitive Electrical Insulating Tape

ABSTRACT
This specification covers electrical insulating tape consisting of a backing made from polyethylene plastic film, coated on one side with a pressure-sensitive adhesive. The backing shall be polyethylene, suitably compounded to meet the requirements prescribed. The standard widths and lengths of the material are presented. The selection of rolls, conditioning, and testing shall meet the requirements prescribed.
SCOPE
1.1 This specification covers electrical insulating tape consisting of a backing made from polyethylene plastic film, coated on one side with a pressure-sensitive adhesive.
1.2 The values stated in SI units are the standard. The values given in parentheses are provided for information purposes only.

General Information

Status
Historical
Publication Date
09-Mar-1999
ICS
29.035.20 - Plastics and rubber insulating materials
Technical Committee
D09 - Electrical and Electronic Insulating Materials
Drafting Committee
D09.07 - Electrical Insulating Materials
Current Stage
Ref Project

Relations

Replaces
ASTM D3006-99 - Standard Specification for Polyethylene Plastic Pressure-Sensitive Electrical Insulating Tape
Effective Date
10-Mar-1999
Replaced By
ASTM D3006-10 - Standard Specification for Polyethylene Plastic Pressure-Sensitive Electrical Insulating Tape
Effective Date
01-May-2010
Referred By
ASTM F1347-23 - Standard Specification for Manually Operated Fueling Hose Reels
Effective Date
10-Mar-1999

Buy Standard

ASTM D3006-99(2004) - Standard Specification for Polyethylene Plastic Pressure-Sensitive Electrical Insulating TapeASTM D3006-99(2004) - Standard Specification for Polyethylene Plastic Pressure-Sensitive Electrical Insulating Tape
PreviousNext
Technical specification
ASTM D3006-99(2004) - Standard Specification for Polyethylene Plastic Pressure-Sensitive Electrical Insulating Tape
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information.
An American National Standard
Designation: D3006 – 99 (Reapproved 2004)
Standard Specification for
Polyethylene Plastic Pressure-Sensitive Electrical Insulating
Tape
This standard is issued under the fixed designation D3006; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 5. Standard Rolls
1.1 This specification covers electrical insulating tape con- 5.1 The standard widths and lengths shall be selected from
sisting of a backing made from polyethylene plastic film, the following:
coated on one side with a pressure-sensitive adhesive. 5.1.1 Widths:
1.2 ThevaluesstatedinSIunitsarethestandard.Thevalues
mm in. mm in.
1 1
6 ⁄4 12 ⁄2
given in parentheses are provided for information purposes
3 5
9 ⁄8 15 ⁄8
only.
3 1
19 ⁄4 30 1 ⁄4
7 1
22 ⁄8 38 1 ⁄2
2. Referenced Documents
25 1 50 2
2.1 ASTM Standards:
Widths greater than 50 mm (2 in.) shall be agreed upon
D1000 Test Methods for Pressure-Sensitive Adhesive-
between the purchaser and the seller.
Coated Tapes Used for Electrical and Electronic Applica-
5.1.2 Lengths:
tions
D1711 Terminology Relating to Electrical Insulation
mft
3. Terminology
20 66
33 108
3.1 Definitions—For definitions of terms in this specifica-
tion refer to Terminology D1711. 5.1.3 Nonstandard widths and lengths are permissible if
agreed to between the purchaser and seller.
4. Material
6. Physical Requirements Physical Requirements
4.1 The backing shall be polyethylene, suitably com-
pounded to meet the requirements of this specification. The 6.1 The tape shall meet the requirements listed in Table 1.
backing shall be smooth and uniform. The tape edges shall be 6.2 Black plastic backing shall be considered standard.
straight and unbroken. Backing of a different color than black shall be specified on the
4.2 The pressure-sensitive coating shall be smooth and purchase order.
uniform, and essentially free from lumps and bare spots. “Fish
7. Test Methods
eyes” shall not be cause for rejection. There shall be no
7.1 The selection of rolls, conditioning, and testing shall be
adhesive transfer when the tape is unwound from the roll.
in accordance with Test Methods D1000.
This specification is under the jurisdiction of ASTM Committee D09 on
8. Rejection
Electrical and Electronic Insulating Materials and is the direct responsibility of
8.1 If the test results of any roll do not conform to the
Subcommittee D09.07 on Flexible and Rigid Insulating Materials.
Current edition approved Nov. 1, 2004. Published May 1999. Originally requirements prescribed in the specification, two additional
´1
approved in 1972. Last previous edition approved in 1993 as D3006–89 (1993) .
rolls shall be selected and tested. If one of the two additional
DOI: 10.1520/D3006-99R04.
sample rolls also does not conform to the requirements, the lot
For referenced ASTM standards, visit the ASTM websit
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D3005-24(Specification)
Standard Specification for Low-Temperature Resistant Vinyl Chloride Plastic Pressure-Sensitive Electrical Insulating Tape

ABSTRACT
This specification covers the properties and requirements for electrical insulating tape consisting of a backing of vinyl chloride plastic, coated on one side with a pressure-sensitive adhesive, for use at low temperatures. Four types are included providing two thicknesses at two operating temperatures. Selected from standard widths and lengths, the tapes shall conform to specified values of the following requirements: break strength; break and static elongation; dielectric breakdown; adhesion to both steel and backing; roll unwind; high-humidity insulation resistance; flammability; and behavior during flagging test.
SCOPE
1.1 This specification covers an electrical insulating tape for use at low temperature down to approximately -18 °C (0 °F). The tape consists of a backing of vinyl chloride plastic, coated on one side with a pressure-sensitive adhesive. Four types are included providing two thicknesses at two operating temperatures.  
1.2 The values stated in SI units are the standard. The values given in parentheses are provided for information purposes only.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM D2301-24(Specification)
Standard Specification for Vinyl Chloride Plastic Pressure-Sensitive Electrical Insulating Tape

ABSTRACT
This specification covers electrical insulating tape consisting of a flexible backing made from vinyl chloride plastic coated on one side with a pressure-sensitive adhesive. The tape shall be classified according to thickness: Type I and Type II. The backing shall be polyvinyl chloride plastic suitably compounded to meet the requirements of this specification. The backing shall be smooth and uniform. The selection of rolls, conditioning, and testing shall be in accordance with the specified requirements.
SCOPE
1.1 This specification covers electrical insulating tape consisting of a flexible backing made from vinyl chloride plastic coated on one side with a pressure-sensitive adhesive.  
1.2 The values stated in SI units are the standard. The values given in parentheses are provided for information purposes only.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D2655-23(Specification)
Standard Specification for Crosslinked Polyethylene Insulation for Wire and Cable Rated 0 to 2000 V, 90 °C Operation

ABSTRACT
This specification covers crosslinked polymer insulation material consisting substantially of polyethylene or a polyethylene copolymer for electrical wires and cables in conductor, suitable for continuous use on power cables in wet and dry locations, having specified sizes and operating at specified voltage ratings and conductor temperatures. Materials covered by this specification are not sunlight and weather resistant unless they are carbon black pigmented or contain an additive system designed for this protection. Since the insulation cannot be tested unless it has been formed around a conductor, tests shall then be done on insulated wire solely to determine the relevant property of the insulation and not to test the conductor or completed cable. Materials shall meet the physical properties as follows: unaged tensile strength and elongation at rupture; tensile strength and elongation at rupture after air oven aging; heat distortion; filled and unfilled percent hot creep; and filled and unfilled percent hot set. Insulations shall also perform satisfactorily during tests for AC and DC voltage, insulation resistance, and accelerated water absorption.
SCOPE
1.1 This specification covers a crosslinked polyethylene insulation for electrical wires and cables in conductor sizes 14 AWG [2.08 mm2] and larger. The base polymer of this insulation consists substantially of polyethylene or a polyethylene copolymer.  
1.2 This type of insulation is suitable for continuous use on power cables in wet and dry locations, for voltage ratings not exceeding 2000 V and at conductor temperatures not exceeding 90 °C for normal operation. For copper conductors, the insulation can be applied over the uncoated metal.  
1.3 Materials covered by this specification are not sunlight and weather resistant unless they are carbon black pigmented or contain an additive system designed for this protection.  
1.4 In many instances the insulation cannot be tested unless it has been formed around a conductor. Therefore, tests are done on insulated wire in this standard solely to determine the relevant property of the insulation and not to test the conductor or completed cable.  
1.5 Whenever two sets of values are presented, in different units, the values in the first set are the standard, while those in parentheses are for information only.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM D3144-23(Specification)
Standard Specification for Crosslinked Poly(Vinylidene Fluoride) and Poly(Vinylidene Fluoride) Copolymer Heat-Shrinkable Tubing for Electrical Insulation

ABSTRACT
This specification covers semirigid, flame-retardant, crosslinked poly(vinylidene fluoride) heat-shrinkable tubing for electrical insulation purposes. It is supplied in an expanded form and will shrink to its extruded diameter when heated. The tubing shall be extruded, crosslinked, and then expanded to the required dimensions. The material shall conform to the chemical property requirements specified. Every lot of material manufactured shall be tested for restricted shrinkage, heat shock, tensile strength, and elongation to conform to the mechanical, thermal, electrical requirements.
SCOPE
1.1 This specification covers semirigid, flame-retardant, crosslinked poly(vinylidene fluoride) heat-shrinkable tubing for electrical insulation purposes. It is supplied in an expanded form and will shrink to its extruded diameter when heated.
Note 1: This standard is similar but not identical to IEC 60684–3–228.  
1.2 The values stated in inch-pound units are to be regarded as the standard, except temperature which shall be stated in degrees Celsius. Values in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM D922-23(Specification)
Standard Specification for Nonrigid Vinyl Chloride Polymer Tubing

ABSTRACT
This specification covers three grades of nonrigid tubing of vinyl chloride polymer or its copolymers with other materials for use in electrical insulation. Clear transparent, black, white, yellow, green, blue, and red shall be considered standard colors. Colors other than these shall be considered special. Dimensional requirements to which tubing shall adhere are inside diameter, wall thickness, and commercial lengths. The tubing shall also conform to physical and electrical requirements, as follows: flammability; tensile strength; effect of elevated temperatures; ultimate elongation after immersion in oil; brittleness temperature; penetration resistance; volume resistivity; dielectric breakdown at high humidity; strain relief; and corrosive effect.
SCOPE
1.1 This specification covers nonrigid tubing of vinyl chloride polymer or its copolymers with other materials for use in electrical insulation in three grades, as follows:  
1.1.1 Grade A—General-purpose.  
1.1.2 Grade B—Low-temperature.  
1.1.3 Grade C—High-temperature.  
1.2 This standard and IEC-60684-3-100 to -105 address the same subject matter but differ in technical content.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM D2148-22(Test Method)
Standard Test Methods for Bondable Silicone Rubber Tapes Used for Electrical Insulation

SIGNIFICANCE AND USE
5.1 Self-adhesion is a primary initial property since it affects layer-to-layer bonding. The integrity of the bond can significantly affect the electrical and physical performance of the insulation system. Therefore, the degree of self-adhesion is directly related to apparatus performance.  
5.2 A high degree of self-adhesion is desirable for most electrical applications. In this test, a short unwinding length indicates a high degree of self-adhesion.  
5.3 This test method has been found useful as a quality control test for lot acceptance.
SCOPE
1.1 These test methods cover tests for bondable silicone rubber tapes which form a sealed structure either with the application of heat (and pressure if needed) or by the process of auto-adhesion (self-fusing).  
1.2 These test methods appear in the following sections:    
Test Method  
Section  
Adhesion  
3 – 10  
Bond Strength  
11 – 18  
Dielectric Breakdown Voltage  
19 – 26  
Hardness  
41  
Length  
33 and 34  
Thickness  
27 – 32  
Width  
36 – 40  
1.3 Units—The values stated in SI units are the standard. The inch-pound units in parentheses are for information only. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  For a specific hazard statement see 23.1.1.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM D4313-22(Specification)
Standard Specification for General-Purpose, Heavy-Duty, and Extra-Heavy-Duty Crosslinked Chlorinated Polyethylene (CPE) Jackets For Wire and Cable

ABSTRACT
This specification covers crosslinked chlorinated polyethylene compounds intended for use as jacket materials (outer coverings) on electrical wires and cables for general-purpose, heavy-duty, and extra-heavy-duty service. The materials under this specification, however, are not recommended for applications with very low temperature service requirement. Physical tests shall be performed and shall conform to the physical property requirements specified such as tensile strength, tensile stress at elongation, elongation at rupture, and tension set. Per service requirement, additional tests for sunlight and weather resistance shall be performed as well, and shall conform to the tensile strength and elongation requirements specified.
SCOPE
1.1 This specification covers crosslinked chlorinated polyethylene (CPE) compounds suitable for use as outer coverings or jackets on electrical cables for general-purpose, heavy-duty, and extra-heavy-duty service.  
1.2 These jacket materials are not recommended for use on cables which are to be installed at a temperature less than –25 °C.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D4363-22(Specification)
Standard Specification for Thermoplastic Chlorinated Polyethylene (CPE) Jacket for Wire and Cable

ABSTRACT
This specification covers thermoplastic chlorinated polyethylene (CM) compounds suitable for use as an outer covering or jacket on electrical cables. Thermoplastic jackets shall conform to the requirements for physical properties specified. The sunlight and weather resistance of the jackets shall be tested to meet the requirements specified.
SCOPE
1.1 This specification covers thermoplastic chlorinated polyethylene (CPE) compounds suitable for use as an outer covering or jacket on electrical cables.  
1.2 These jacket materials are suitable for use on cables which will be installed at temperatures above –35 °C.  
1.3 The values stated in inch-pound units are regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D2902-21(Specification)
Standard Specification for Fluoropolymer Resin Heat-Shrinkable Tubing for Electrical Insulation

ABSTRACT
This specification applies to flexible fluoropolymer resin heat-shrinkable extruded tubing made from tetrafluoroethylene resin, copolymer of tetrafluoroethylene and hexafluoropropylene (FEP), and from perfluoroalkoxy (PFA) resin for use as electrical insulation. This specification covers three types of tubings, namely: Type I tubing, normally made by paste extrusion, and Type II and Type III tubings, normally made by melt extrusion. The finished compound shall be free of all foreign matter other than intended formulation additives. The material shall conform to the specified chemical and physical property requirements such as: (1) restricted shrinkage, (2) specific gravity, (3) longitudinal change, (4) tensile modulus at elongation, (5) volume resistivity, (6) dielectric breakdown voltage, (7) heat resistance, (8) low-temperature flexibility, and (9) melting point. The dimensional requirements after unrestrictive shrinkage such as inside diameter, wall thickness, and stock lengths are specified. The sampling and test methods to determine conformance to the specified requirements are given.
SCOPE
1.1 This specification applies to flexible heat-shrinkable extruded tubing made from tetrafluoroethylene resin, copolymer of tetrafluoroethylene and hexafluoropropylene, and from perfluoroalkoxy resin for use as electrical insulation. This specification excludes crosslinked poly(vinylidene fluoride) and poly(vinylidene fluoride) copolymer which are covered under Specification D3144.
Note 1: This standard is similar but not identical to IEC 60684-3-240.  
1.2 The values stated in inch-pound units are to be regarded as standard, except temperature, which shall be stated in degrees Celsius. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    7 pages
    English language
    sale 15% off
  • Technical specification
    7 pages
    English language
    sale 15% off
ASTM
ASTM D1047-21(Specification)
Standard Specification for Poly(Vinyl Chloride) Jacket for Wire and Cable

ABSTRACT
This specification covers a durable general-purpose thermoplastic jacket made from poly(vinyl chloride) or the copolymer of vinyl chloride and vinyl acetate for use in wires and cables at specified minimum installing temperature. The jackets shall meet specified values of the following physical and electrical properties: unexposed (unaged) tensile strength and elongation at rupture; tensile strength and elongation at rupture after air oven aging and oil immersion tests; heat distortion; heat shock; cold bend; surface resistivity; and U-bend discharge at required cable insulation AC test voltage.
SCOPE
1.1 This specification covers a durable general-purpose thermoplastic jacket made from poly(vinyl chloride) or the copolymer of vinyl chloride and vinyl acetate suitable for a minimum installing temperature of −10 °C.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off