ASTM F2764/F2764M-11ae2

Standard Specification for 30 to 60 in. [750 to 1500 mm] Polypropylene (PP) Triple Wall Pipe and Fittings for Non-Pressure Sanitary Sewer Applications

SCOPE
1.1 This specification covers requirements and test methods for triple wall polypropylene pipe and fittings. The nominal inside diameters covered are 30 to 60 in. [750 to 1600 mm].  
1.2 The requirements of this specification are intended to provide pipe and fittings suitable for underground use for non-pressure sanitary sewer systems. Pipe and fittings produced in accordance with this specification shall be installed in compliance with Practice D2321.  
1.3 This specification covers pipe and fittings with an essentially smooth interior wall, an essentially smooth exterior wall and an annular corrugated profile middle wall (Fig. 1).  
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.5 The following precautionary statement applies only to Section 7 of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 30-Apr-2011
• ICS: 91.140.80 - Drainage systems
• Technical Committee: F17 - Plastic Piping Systems
• Drafting Committee: F17.62 - Sewer

Relations

• Replaces: ASTM F2764/F2764M-11ae1 - Standard Specification for 30 to 60 in. [750 to 1500 mm] Polypropylene (PP) Triple Wall Pipe and Fittings for Non-Pressure Sanitary Sewer Applications
• Effective Date: 01-May-2011
• Replaced By: ASTM F2764/F2764M-16 - Standard Specification for 6 to 60 in. [150 to 1500 mm] Polypropylene (PP) Corrugated Double and Triple Wall Pipe and Fittings for Non-Pressure Sanitary Sewer Applications
• Effective Date: 01-Aug-2016
• Referred By: ASTM D2412-21 - Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
• Effective Date: 01-May-2011
• Referred By: ASTM F2487-21 - Standard Practice for Infiltration and Exfiltration Acceptance Testing of Installed Corrugated High Density Polyethylene and Polypropylene Pipelines
• Effective Date: 01-May-2011
• Referred By: ASTM F2510/F2510M-22 - Standard Specification for Resilient Connectors Between Reinforced Concrete Manhole Structures and Corrugated Dual- and Triple-Wall Polyethylene and Polypropylene Pipes
• Effective Date: 01-May-2011

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
´2
Designation:F2764/F2764M −11a
StandardSpecification for
30 to 60 in. [750 to 1500 mm] Polypropylene (PP) Triple Wall
Pipe and Fittings for Non-Pressure Sanitary Sewer
1
Applications
ThisstandardisissuedunderthefixeddesignationF2764/F2764M;thenumberimmediatelyfollowingthedesignationindicatestheyear
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1
ε NOTE—Revised designation to correspond with units statement in November 2013.
2
ε NOTE—Table 1 headings were editorially added in July 2014.
1. Scope* Stainless Steel Sheet, Strip, Plate, and Flat Bar
D256 Test Methods for Determining the Izod Pendulum
1.1 This specification covers requirements and test methods
Impact Resistance of Plastics
for triple wall polypropylene pipe and fittings. The nominal
D618 Practice for Conditioning Plastics for Testing
inside diameters covered are 30 to 60 in. [750 to 1600 mm].
D638 Test Method for Tensile Properties of Plastics
1.2 The requirements of this specification are intended to
D790 Test Methods for Flexural Properties of Unreinforced
provide pipe and fittings suitable for underground use for
and Reinforced Plastics and Electrical Insulating Materi-
non-pressure sanitary sewer systems. Pipe and fittings pro-
als
duced in accordance with this specification shall be installed in
D792 Test Methods for Density and Specific Gravity (Rela-
compliance with Practice D2321.
tive Density) of Plastics by Displacement
1.3 This specification covers pipe and fittings with an
D1238 Test Method for Melt Flow Rates of Thermoplastics
essentially smooth interior wall, an essentially smooth exterior
by Extrusion Plastometer
wall and an annular corrugated profile middle wall (Fig. 1).
D1505 Test Method for Density of Plastics by the Density-
1.4 The values stated in either SI units or inch-pound units Gradient Technique
are to be regarded separately as standard. The values stated in D1600 Terminology forAbbreviatedTerms Relating to Plas-
each system may not be exact equivalents; therefore, each tics
system shall be used independently of the other. Combining
D2122 Test Method for Determining Dimensions of Ther-
values from the two systems may result in non-conformance
moplastic Pipe and Fittings
with the standard.
D2321 PracticeforUndergroundInstallationofThermoplas-
tic Pipe for Sewers and Other Gravity-Flow Applications
1.5 The following precautionary statement applies only to
D2412 Test Method for Determination of External Loading
Section 7 of this specification. This standard does not purport
to address all of the safety concerns, if any, associated with its Characteristics of Plastic Pipe by Parallel-Plate Loading
use. It is the responsibility of the user of this standard to D2444 Test Method for Determination of the Impact Resis-
establish appropriate safety and health practices and deter- tance of Thermoplastic Pipe and Fittings by Means of a
mine the applicability of regulatory limitations prior to use. Tup (Falling Weight)
D2990 Test Methods for Tensile, Compressive, and Flexural
2. Referenced Documents
Creep and Creep-Rupture of Plastics
2
D3212 Specification for Joints for Drain and Sewer Plastic
2.1 ASTM Standards:
Pipes Using Flexible Elastomeric Seals
A666 Specification forAnnealed or Cold-WorkedAustenitic
D3895 Test Method for Oxidative-Induction Time of Poly-
olefins by Differential Scanning Calorimetry
1
This specification is under the jurisdiction ofASTM Committee F17 on Plastic
D4101 Specification for Polypropylene Injection and Extru-
Piping Systems and is the direct responsibility of Subcommittee F17.62 on Sewer.
sion Materials
Current edition approved May 1, 2011. Published May 2011. Originally
D4218 Test Method for Determination of Carbon Black
approved in 2010. Last previous edition approved in 2011 as F2764–11.
DOI:10.1520/D2764_F2764M–11AE01.
Content in Polyethylene Compounds By the Muffle-
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Furnace Technique
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
D4389 SpecificationforFinishedGlassFabricsWovenFrom
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. Rovings
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
´2
F2764/F2764M−11a
FIG. 1 Typical Triple Wall Pipe Profile
D6992 Test Method for Accelerated Tensile Creep and 4. Ordering Information
Creep-Rupture of Geosynthetic Materials Based on Time-
4.1 Orders for product made to this specification shall
Temp
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
´2 ´2
Designation: F2764/F2764M − 11a F2764/F2764M − 11a An American National Standard
Standard Specification for
30 to 60 in. [750 to 1500 mm] Polypropylene (PP) Triple Wall
Pipe and Fittings for Non-Pressure Sanitary Sewer
1
Applications
This standard is issued under the fixed designation F2764/F2764M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1
ε NOTE—Revised designation to correspond with units statement in November 2013.
2
ε NOTE—Table 1 headings were editorially added in July 2013.
1. Scope*
1.1 This specification covers requirements and test methods for triple wall polypropylene pipe and fittings. The nominal inside
diameters covered are 30 to 60 in. [750 to 1600 mm].
1.2 The requirements of this specification are intended to provide pipe and fittings suitable for underground use for non-pressure
sanitary sewer systems. Pipe and fittings produced in accordance with this specification shall be installed in compliance with
Practice D2321.
1.3 This specification covers pipe and fittings with an essentially smooth interior wall, an essentially smooth exterior wall and
an annular corrugated profile middle wall (Fig. 1).
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each
system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the
two systems may result in non-conformance with the standard.
1.5 The following precautionary statement applies only to Section 7 of this specification. This standard does not purport to
address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish
appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
A666 Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar
D256 Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
D618 Practice for Conditioning Plastics for Testing
D638 Test Method for Tensile Properties of Plastics
D790 Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
D792 Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
D1238 Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer
D1505 Test Method for Density of Plastics by the Density-Gradient Technique
D1600 Terminology for Abbreviated Terms Relating to Plastics
D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D2321 Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
D2412 Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
D2444 Test Method for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling
Weight)
D2990 Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics
D3212 Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.62 on Sewer.
Current edition approved May 1, 2011. Published May 2011. Originally approved in 2010. Last previous edition approved in 2011 as F2764–11. DOI:10.1520/D2764_
F2764M–11AE01.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
´2
F2764/F2764M − 11a
FIG. 1 Typical Triple Wall Pipe Profile
D3895 Test Method for Oxidative-Induction Time of Polyolefins by Differential Scanning Calorimetry
D4101 Specification for Polypropylene Injection and Extrusion Materials
D4218 Test Method for Det
...