ASTM F2764/F2764M-23

Standard Specification for 6 in. to 60 in. [150 mm to 1500 mm] Polypropylene (PP) Corrugated Double and Triple Wall Pipe and Fittings for Non-Pressure Sanitary Sewer Applications

ABSTRACT
This specification covers requirements and test methods for triple wall polypropylene pipe and fittings with nominal inside diameters of 30 to 60 in. [750 to 1600 mm]. These requirements are intended to provide pipe and fittings suitable for underground use for non-pressure sanitary sewer systems. Pipe and fittings produced in accordance with this specification shall be installed in compliance with Practice D2321. Pipe and fittings with a interior wall, a exterior wall and an annular corrugated profile middle wall are covered by this specification.
SCOPE
1.1 This specification covers requirements and test methods for corrugated double and triple wall polypropylene pipe and fittings. The nominal inside diameters covered are 6 in. to 60 in. [150 mm to 1500 mm].  
1.2 The requirements of this specification are intended to provide pipe and fittings for underground use for non-pressure sanitary sewer systems. Pipe and fittings produced in accordance with this specification shall be installed in compliance with Practice D2321.  
1.3 This specification covers pipe and fittings with an annular corrugated wall and an essentially smooth interior wall (that is, double wall) (Fig. 1) and pipe and fittings with an annular corrugated wall and an essentially smooth interior and exterior wall (that is, triple wall) (Fig. 2).
FIG. 1 Typical Corrugated Double Wall Pipe
FIG. 2 Typical Corrugated Triple Wall Pipe  
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.5 The following precautionary statement applies only to Section 7 of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

• Status: Published
• Publication Date: 31-Jan-2023
• ICS: 91.140.80 - Drainage systems
• Technical Committee: F17 - Plastic Piping Systems
• Drafting Committee: F17.62 - Sewer

Relations

• Refers: ASTM D4218-20 - Standard Test Method for Determination of Carbon Black Content in Polyethylene Compounds by the Muffle-Furnace Technique
• Effective Date: 01-Feb-2020
• Refers: ASTM D2321-20 - Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
• Effective Date: 15-Mar-2020
• Refers: ASTM F412-20 - Standard Terminology Relating to Plastic Piping Systems
• Effective Date: 01-Apr-2020

Standards Content (Sample)

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: F2764/F2764M − 23
Standard Specification for
6 in. to 60 in. [150 mm to 1500 mm] Polypropylene (PP)
Corrugated Double and Triple Wall Pipe and Fittings for
1
Non-Pressure Sanitary Sewer Applications
This standard is issued under the fixed designation F2764/F2764M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 2. Referenced Documents
2
1.1 This specification covers requirements and test methods 2.1 ASTM Standards:
for corrugated double and triple wall polypropylene pipe and A666 Specification for Annealed or Cold-Worked Austenitic
fittings. The nominal inside diameters covered are 6 in. to 60 Stainless Steel Sheet, Strip, Plate, and Flat Bar
in. [150 mm to 1500 mm]. D256 Test Methods for Determining the Izod Pendulum
Impact Resistance of Plastics
1.2 The requirements of this specification are intended to
D578/D578M Specification for Glass Fiber Strands
provide pipe and fittings for underground use for non-pressure
D618 Practice for Conditioning Plastics for Testing
sanitary sewer systems. Pipe and fittings produced in accor-
D638 Test Method for Tensile Properties of Plastics
dance with this specification shall be installed in compliance
D790 Test Methods for Flexural Properties of Unreinforced
with Practice D2321.
and Reinforced Plastics and Electrical Insulating Materi-
1.3 This specification covers pipe and fittings with an
als
annular corrugated wall and an essentially smooth interior wall
D792 Test Methods for Density and Specific Gravity (Rela-
(that is, double wall) (Fig. 1) and pipe and fittings with an
tive Density) of Plastics by Displacement
annular corrugated wall and an essentially smooth interior and
D1238 Test Method for Melt Flow Rates of Thermoplastics
exterior wall (that is, triple wall) (Fig. 2).
by Extrusion Plastometer
1.4 The values stated in either SI units or inch-pound units D1505 Test Method for Density of Plastics by the Density-
Gradient Technique
are to be regarded separately as standard. The values stated in
each system may not be exact equivalents; therefore, each D1600 Terminology for Abbreviated Terms Relating to Plas-
system shall be used independently of the other. Combining tics
D2122 Test Method for Determining Dimensions of Ther-
values from the two systems may result in non-conformance
with the standard. moplastic Pipe and Fittings
D2321 Practice for Underground Installation of Thermoplas-
1.5 The following precautionary statement applies only to
tic Pipe for Sewers and Other Gravity-Flow Applications
Section 7 of this specification. This standard does not purport
D2412 Test Method for Determination of External Loading
to address all of the safety concerns, if any, associated with its
Characteristics of Plastic Pipe by Parallel-Plate Loading
use. It is the responsibility of the user of this standard to
D2444 Practice for Determination of the Impact Resistance
establish appropriate safety, health, and environmental prac-
of Thermoplastic Pipe and Fittings by Means of a Tup
tices and determine the applicability of regulatory limitations
(Falling Weight)
prior to use.
D2990 Test Methods for Tensile, Compressive, and Flexural
1.6 This international standard was developed in accor-
Creep and Creep-Rupture of Plastics
dance with internationally recognized principles on standard-
D3212 Specification for Joints for Drain and Sewer Plastic
ization established in the Decision on Principles for the
Pipes Using Flexible Elastomeric Seals
Development of International Standards, Guides and Recom-
D3895 Test Method for Oxidative-Induction Time of Poly-
mendations issued by the World Trade Organization Technical
olefins by Differential Scanning Calorimetry
Barriers to Trade (TBT) Committee.
D4101 Classification System and Basis for Specification for
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic
2
Piping Systems and is the direct responsibility of Subcommittee F17.62 on Sewer. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Feb. 1, 2023. Published April 2023. Originally contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
approved in 2010. Last previous edition approved in 2019 as F2764/F2764M–19. Standards volume information, refer to the standard’s Document Summary page on
DOI:10.1520/F2764_F2764M–23. the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM Internationa
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F2764/F2764M − 19 F2764/F2764M − 23
Standard Specification for
66 in. to 60 in. [150[150 mm to 1500 mm] Polypropylene (PP)
Corrugated Double and Triple Wall Pipe and Fittings for
1
Non-Pressure Sanitary Sewer Applications
This standard is issued under the fixed designation F2764/F2764M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification covers requirements and test methods for corrugated double and triple wall polypropylene pipe and fittings.
The nominal inside diameters covered are 66 in. to 60 in. [150[150 mm to 1500 mm].
1.2 The requirements of this specification are intended to provide pipe and fittings for underground use for non-pressure sanitary
sewer systems. Pipe and fittings produced in accordance with this specification shall be installed in compliance with Practice
D2321.
1.3 This specification covers pipe and fittings with an annular corrugated wall and an essentially smooth interior wall (that is,
double wall) (Fig. 1) and pipe and fittings with an annular corrugated wall and an essentially smooth interior and exterior wall (that
is, triple wall) (Fig. 2).
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each
system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the
two systems may result in non-conformance with the standard.
1.5 The following precautionary statement applies only to Section 7 of this specification. This standard does not purport to
address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish
appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
A666 Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar
D256 Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
D578/D578M Specification for Glass Fiber Strands
D618 Practice for Conditioning Plastics for Testing
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.62 on Sewer.
Current edition approved April 1, 2019Feb. 1, 2023. Published May 2019April 2023. Originally approved in 2010. Last previous edition approved in 20182019 as
F2764/F2764M–18a. DOI:10.1520/F2764_F2764M–19. –19. DOI:10.1520/F2764_F2764M–23.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F2764/F2764M − 23
FIG. 1 Typical Corrugated Double Wall Pipe
FIG. 2 Typical Corrugated Triple Wall Pipe
D638 Test Method for Tensile Properties of Plastics
D790 Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
D792 Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
D1238 Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer
D1505 Test Method for Density of Plastics by the Density-Gradient Technique
D1600 Terminology for Abbreviated Terms Relating to Plastics
D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D2321 Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
D2412 Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
D2444 Practice for Determination of t
...