ASTM D3239-91(2001)
(Test Method)Standard Test Method for Aromatic Types Analysis of Gas-Oil Aromatic Fractions by High Ionizing Voltage Mass Spectrometry
Standard Test Method for Aromatic Types Analysis of Gas-Oil Aromatic Fractions by High Ionizing Voltage Mass Spectrometry
SCOPE
1.1 This test method covers the determination by high ionizing voltage, low resolution mass spectrometry of 18 aromatic hydrocarbon types and 3 aromatic thiophenotypes in straight run aromatic petroleum fractions boiling within the range from 205 to 540°C (400 to 1000°F) (corrected to atmospheric pressure). Samples must be nonolefinic, must contain not more than 1 mass % of total sulfur, and must contain not more than 5 % nonaromatic hydrocarbons. Composition data are in volume percent.
Note 1—Although names are given to 15 of the compound types determined, the presence of other compound types of the same empirical formulae is not excluded. All other compound types in the sample, unidentified by name or empirical formula, are lumped into six groups in accordance with their respective homologous series.
1.2 The values stated in acceptable SI units are to be regarded as the standard. The values given in parentheses are provided for information purposes only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
An American National Standard
Designation:D3239–91(Reapproved 2001)
Standard Test Method for
Aromatic Types Analysis of Gas-Oil Aromatic Fractions by
High Ionizing Voltage Mass Spectrometry
This standard is issued under the fixed designation D3239; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope Quantitative Analysis from a Batch Inlet
1.1 This test method covers the determination by high
3. Terminology
ionizing voltage, low resolution mass spectrometry of 18
3.1 Definitions of Terms Specific to This Standard:
aromatic hydrocarbon types and 3 aromatic thiophenotypes in
3.1.1 Characteristic Mass Summations— Classes I–VII:
straight run aromatic petroleum fractions boiling within the
3.1.2 Class I:
range from 205 to 540°C (400 to 1000°F) (corrected to
(78 578 192 1106 1120 1.toend,polyisotopic
atmospheric pressure). Samples must be nonolefinic, must
191 1105 1119 1.toend,monoisotopic (1)
contain not more than 1 mass% of total sulfur, and must
contain not more than 5% nonaromatic hydrocarbons. Com-
3.1.3 Class II:
position data are in volume percent.
(104 5104 1118 1132 1146 1.toend,polyisotopic
1117 1131 1145 1.toend,monoisotopic (2)
NOTE 1—Although names are given to 15 of the compound types
determined, the presence of other compound types of the same empirical
3.1.4 Class III:
formulae is not excluded. All other compound types in the sample,
(129 5130 1144 1158 1172 1.toend,polyisotopic
unidentified by name or empirical formula, are lumped into six groups in
1129 1143 1157 1171 1.toend,monoisotopic (3)
accordance with their respective homologous series.
3.1.5 Class IV:
1.2 The values stated in acceptable SI units are to be
regarded as the standard. The values given in parentheses are
(128 5128 1142 1156 1170 1.toend,polyisotopic
1141 1155 1169 1.toend,monoisotopic (4)
provided for information purposes only.
1.3 This standard does not purport to address all of the
3.1.6 Class V:
safety concerns, if any, associated with its use. It is the
(154 5154 1168 1182 1196 1.toend,polyisotopic
responsibility of the user of this standard to establish appro-
1167 1181 1195 1.toend,monoisotopic (5)
priate safety and health practices and determine the applica-
3.1.7 Class VI:
bility of regulatory limitations prior to use.
(166 5166 1180 1194 1208 1.toend,polyisotopic
2. Referenced Documents
1179 1193 1207 1.toend,monoisotopic (6)
2.1 ASTM Standards:
3.1.8 Class VII:
D2549 Test Method for Separation of Representative Aro-
(178 5178 1192 1206 1220 1.toend,polyisotopic
matics and Nonaromatics Fractions of High-Boiling Oils
1191 1205 1219 1.toend,monoisotopic (7)
by Elution Chromatography
3.1.9 Classes, Compound Types, Empirical Formulae—See
D2786 Test Method for Hydrocarbon Types Analysis of
Table 1.
Gas-Oil Saturate Fractions by High IonizingVoltage Mass
Spectrometry
4. Summary of Test Method
E137 Practice for Evaluation of Mass Spectrometers for
4.1 The relative abundance of seven classes (I–VII) of
aromatics in petroleum aromatic fractions is determined by
mass spectrometry using a summation of peaks most charac-
teristic of each class. Calculations are carried out by the use of
This test method is under the jurisdiction of ASTM Committee D02 on
PetroleumProductsandLubricantsandisthedirectresponsibilityofSubcommittee a7by7invertedmatrixderivedfrompublishedspectraofpure
D02.04 on Hydrocarbon Analysis.
aromatic compounds. Each summation of peaks includes the
Current edition approved Oct. 15, 1991. Published December 1991. Originally
polyisotopic homologous series that contains molecular ions
published as D3239–73T. Last previous edition D3239–86.
Robinson, C. J., and Cook, G. L., Analytical Chemistry (ANCHA), Vol 41,
1969, p. 1548.
3 4
Annual Book of ASTM Standards, Vol 05.01. Discontinued—See 1992 Annual Book of ASTM Standards, Vol 05.03.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
D3239–91 (2001)
TABLE 1 Classes, Compound Types, and Empirical Formulae
in the spectrum. Any digitizing system capable of supplying
Class Type Formula accurate mass numbers and peak heights is suitable.
I 0 alkylbenzenes, C H
n 2n-6 6.5 Electronic Digital Computer—The computations for
I 1 benzothiophenes, C H S
n 2n-10
this analysis are not practical without the use of a computer.
I 2 naphthenephenanthrenes,
C H Any computer capable of providing approximately 60K bytes
n 2n-20
II 0 naphthenebenzenes, C H
n 2n-8
in core and capable of compiling programs written in FOR-
II 1 pyrenes, C H
n 2n-22
TRAN IV should be suitable.
II 2 unidentified
III 0 dinaphthenebenzenes, C H
n 2n-10
III 1 chrysenes, C H
n 2n-24
7. Reagent
III 2 unidentified
IV 0 naphthalenes, C H
n 2n-12
7.1 n-Hexadecane.(Warning—Combustible-Very harm-
IV 1 dibenzothiophenes, C H S
n 2n-16
ful.)
IV 2 unidentified
V 0 acenaphthenes + dibenzofurans,
C H and C H O
n 2n-14 n 2n-16
8. Calibration
V 1 perylenes, C H
n 2n-28
V 2 unidentified
8.1 Calibration equations in the computer program given in
VI 0 fluorenes, C H
n 2n-16
VI 1 dibenzanthracenes, C H
n 2n-30 Table 2 may be used directly provided the following proce-
VI 2 unidentified
dures are followed:
VII 0 phenanthrenes, C H
n 2n-18
VII 1 naphthobenzothiophenes, C H
n 2n- 8.1.1 Instrumental Conditions—Repeller settings are ad-
22S
justed to maximize the m/e 226 ion of n-hexadecane. A
VII 2 unidentified
magnetic field is used that will permit a scan over the mass
range from 78 to 700. An ionizing voltage of 70 eV and an
ionizing current in the range from 10 to 70 µA is used.
and the monoisotopic homologous series one mass unit less
NOTE 3—The instrument conditions and calibration equations de-
than the molecular ion series. Using characteristic summations
scribed in this method are based on the use of a 180° magnetic-deflection
found in the monoisotopic molecular ion—1 series of peaks,
type mass spectrometer (CEC Model 21-103). Satisfactory results have
eachclassisfurtherresolvedtoproviderelativeabundancesof
been obtained with some other magnetic deflection instruments. It is not
three compound types: nominal (Type 0), first overlap (Type
known if the equations are suitable for use on all other mass spectrometer
1), and second overlap (Type 2). The aromatic fraction is
types.
obtained by liquid elution chromatography (see Test Method
8.1.2 Computer Program—The FORTRAN program given
D2549).
in Table 2 contains all the equations for calculating the
NOTE 2—Monoisotopic peaks heights are obtained by correcting the
analysis, including those for calculating monoisotopic peak
polyisotopicheightsfornaturallyoccurringheavyisotopes,assumingthat
heights. The program is compiled and linked to create a
only ions of C H to C H are present. This is not strictly accurate
n 2n+2 n 2−11
for aromatics, but the errors introduced by such assumption are trivial.
computer load module that is available whenever needed.
When the spectrum shown inTable 3 is processed, thee results
5. Significance and Use
should agree with those shown in Table 4.
5.1 Aknowledgeofthehydrocarboncompositionofprocess
8.1.2.1 Data Input Format—The input format suggested in
streamsandpetroleumproductsboilingwithintherange205to
the main program may be changed to suit the needs of
540°C (400 to 1000°F) is useful in following the effect of
individual laboratories provided that true masses and p
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.