ASTM E2517-13

Standard Specification for Cargo Bed Cover, Type III (M35A2, 2 1/2 Ton Cargo Truck/M1078, 2 1/2 Ton Lightweight Medium Tactical Vehicle (LMTV)/ M1082, 2 1/2 Ton LMTV Trailer)

SCOPE
1.1 This specification covers the general requirements for the Type III Cargo Bed Cover (CBC). The Type III CBC is a removable general purpose rigid wall enclosure that is mounted on any of the following model 2.5 ton cargo trucks (1) the M35A2 Lightweight Medium Tactical Vehicle (LMTV) and (2) the M1078 LMTV. It can also be mounted on the M1082 LMTV Trailer. The CBC provides environmental protection and security for mission equipment and items of general transport.  
1.2 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 The following safety hazards caveat pertains only to the test required portion, Section 4, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

General Information

• Status: Historical
• Publication Date: 30-Sep-2013
• ICS: 43.080.10 - Trucks and trailers
• Technical Committee: E06 - Performance of Buildings
• Drafting Committee: E06.53 - Materials and Processes for Durable Rigidwall Relocatable Structures

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: E2517 −13
Standard Specification for
1
Cargo Bed Cover, Type III (M35A2, 2 ⁄2 Ton Cargo Truck/
1
M1078, 2 ⁄2 Ton Lightweight Medium Tactical Vehicle (LMTV)/
1
1
M1082, 2 ⁄2 Ton LMTV Trailer)
This standard is issued under the fixed designation E2517; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
4
1. Scope 2.2 Federal Standards:
FED-STD-595Colors Used in Government Procurement
1.1 This specification covers the general requirements for
4
2.3 Military Standards:
the Type III Cargo Bed Cover (CBC). The Type III CBC is a
MIL-C-46168Coating, Aliphatic Polyurethane, Chemical
removablegeneralpurposerigidwallenclosurethatismounted
Agent Resistant
on any of the following model 2.5ton cargo trucks (1) the
MIL-CDTL-53039Coating, Aliphatic Polyurethane, Single
M35A2LightweightMediumTacticalVehicle(LMTV)and(2)
Component, Chemical Agent Resistant
the M1078 LMTV. It can also be mounted on the M1082
MIL-CDTL-53072 Chemical Agent Resistant Coating
LMTV Trailer. The CBC provides environmental protection
(CARC)SystemApplicationProceduresandQualityCon-
and security for mission equipment and items of general
trol Inspection
transport.
MIL-PRF-22750Coating, Epoxy, High Solids
1.2 The values stated in inch-pound units are to be regarded
MIL-STD-209Slinging and Tiedown Provisions for Lifting
asstandard.Nootherunitsofmeasurementareincludedinthis
and Tying Down Military Equipment
standard.
MIL-STD-810 Environmental Test Methods and Engineer-
1.3 The following safety hazards caveat pertains only to the
ing Guidelines
test required portion, Section 4, of this specification: This
MIL-STD-1366Transportability Criteria
standard does not purport to address all of the safety concerns,
MIL-STD-1472Design Criteria: Human Engineering
if any, associated with its use. It is the responsibility of the user
4
2.4 Military Handbooks:
of this standard to establish appropriate safety and health
MIL-HDBK-759Human Engineering Design
practicesanddeterminetheapplicabilityofregulatoryrequire-
MIL-HDBK-1791Designing for Internal Aerial Delivery in
ments prior to use.
Fixed Winged Aircraft
5
2.5 OSHA Documents:
2. Referenced Documents
Title 29 CFR 1910OHSA Permissible Exposure Limits
2
2.1 ASTM Standards:
6
2.6 ACGIH Documents:
E1925Specification for Engineering and Design Criteria for
ACGIHThreshold Limit Values
Rigid Wall Relocatable Structures
F501Test Method for Aerospace Materials Response to
3. General Requirements
Flame, with Vertical Test Specimen (for Aerospace Ve-
3
hicles Standard Conditions) (Withdrawn 1998) 3.1 First Article—When specified (see 6.2), a sample shall
besubjectedtofirstarticleinspectioninaccordancewith4.1.1.
A first article is defined as a pre-production or an initial
production sample consisting of one or more of each type of
1
This specification is under the jurisdiction of ASTM Committee E06 on
completed CBC.
Performance of Buildings and is the direct responsibility of Subcommittee E06.53
on Materials and Processes for Durable Rigidwall Relocatable Structures.
Current edition approved Oct. 1, 2013. Published January 2014. Originally
approved in 2006. Last previous edition approved in 2011 as E2517–11. DOI:
4
10.1520/E2517-13. Available from DLA Document Services, Building 4/D, 700 Robbins Avenue,
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or Philadelphia, PA 19111-5094, http://quicksearch.dla.mil/.
5
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Available from Occupational Safety and Health Administration (OSHA), 200
Standards volume information, refer to the standard’s Document Summary page on Constitution Ave., NW, Washington, DC 20210, http://www.osha.gov.
6
the ASTM website. Available from American Conference of Governmental Industrial Hygienists,
3
The last approved version of this historical standard is referenced on Inc. (ACGIH), 1330 Kemper Meadow Dr., Cincinnati, OH 45240, http://
www.astm.org. www.acgih.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
E2517 − 13
3.2 Conformance—Items furnished under this specification 3.3.5.2 Gases or Vapors—The materials, as installed in the
shall be subjected to conformance inspection in accordance equipment and under service conditions specified in the equip-
with 4.1.2. ment specification, shall not liberate noxious odors, toxic or
corrosive gases, or vapors that would be detrimental to the
3.3 Operating Requirements—Unless otherwise specified,
health of personnel.
the Type III CBC shall
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: E2517 − 11 E2517 − 13
Standard Specification for
1
Cargo Bed Cover, Type III (M35A2, 2 ⁄2 1/2 Ton Cargo Truck/
1
M1078, 2 ⁄2 1/2 Ton Lightweight Medium Tactical Vehicle
1
1
(LMTV)/ M1082, 2 ⁄2 1/2 Ton LMTV Trailer)
This standard is issued under the fixed designation E2517; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers the general requirements for the Type III Cargo Bed Cover (CBC). The Type III CBC is a
removable general purpose rigid wall enclosure that is mounted on any of the following model 2.5 ton cargo trucks (1) the M35A2
Lightweight Medium Tactical Vehicle (LMTV) and (2) the M1078 LMTV . LMTV. It can also be mounted on the M1082 LMTV
Trailer. The CBC provides environmental protection and security for mission equipment and items of general transport.
1.2 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this
standard.
1.3 The following safety hazards caveat pertains only to the test required portion, Section 4, of this specification: This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to
use.
2. Referenced Documents
2
2.1 ASTM Standards:
E1925 Specification for Engineering and Design Criteria for Rigid Wall Relocatable Structures
F501 Test Method for Aerospace Materials Response to Flame, with Vertical Test Specimen (for Aerospace Vehicles Standard
3
Conditions) (Withdrawn 1998)
4
2.2 Federal Standards:
FED-STD-595 Colors Used in Government Procurement
4
2.3 Military Standards:
MIL-C-46168 Coating, Aliphatic Polyurethane, Chemical Agent Resistant
MIL-CDTL-53039 Coating, Aliphatic Polyurethane, Single Component, Chemical Agent Resistant
MIL-CDTL-53072 Chemical Agent Resistant Coating (CARC) System Application Procedures and Quality Control Inspection
MIL-PRF-22750 Coating, Epoxy, High Solids
MIL-STD-209 Slinging and Tiedown Provisions for Lifting and Tying Down Military Equipment
MIL-STD-810 Environmental Test Methods and Engineering Guidelines
MIL-STD-1366 Transportability Criteria
MIL-STD-1472 Design Criteria: Human Engineering
4
2.4 Military Handbooks:
MIL-HDBK-759 Human Engineering Design
MIL-HDBK-1791 Designing for Internal Aerial Delivery in Fixed Winged Aircraft
5
2.5 OSHA Documents:
Title 29 CFR 1910 OHSA Permissible Exposure Limits
1
This specification is under the jurisdiction of ASTM Committee E06 on Performance of Buildings and is the direct responsibility of Subcommittee E06.53 on Materials
and Processes for Durable Rigidwall Relocatable Structures.
Current edition approved Sept. 1, 2011Oct. 1, 2013. Published October 2011January 2014. Originally approved in 2006. Last previous edition approved in 20062011 as
E2517 – 06.E2517 – 11. DOI: 10.1520/E2517-11.10.1520/E2517-13.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
The last approved version of this historical standard is referenced on www.astm.org.
4
Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http://www.dodssp.daps.mil.
DLA Document Services, Building 4/D, 700 Robbins Avenue, Philadelphia, PA 19111-5094, http://quicksearch.dla.mil/.
5
Available from Occupational Safety and Health Administration (OSHA), 200 Constitution Ave., NW, Washington, DC 20210, http://www.osha.gov.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
E2517 − 13
6
2.6 ACGIH Documents:
ACGIH Threshold Limit Values
3. General Requirements
3.1 First Article—When specified (see 6.2), a sample shall be subjected to first article inspection in accordance with 4.1.1. A
first article is defined as a pre-production or an initial production sample consisting of one or more of each type of completed CBC.
3.2 Conformance—Items furnished under this specification shall
...